Instrukcja obsługi Garmin GXM 51

Garmin Niesklasyfikowane GXM 51

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Garmin GXM 51 (15 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/15
GXM™ 51 Installation Instructions
The Garmin GXM 51 XM
®
antenna provides XM WX Satellite Weather
®
information and XM
Satellite Radio
®
for your existing NMEA 2000
®
network. If you do not have an existing NMEA
2000 network on your boat, you will need to install one. For more information about NMEA
2000, visit www.garmin.com.
The GXM 51 antenna must be properly installed according to the following instructions.
You need the appropriate fasteners, tools, and mounts listed in each section. These items
are available at most marine dealers. Always wear safety goggles, ear protection, and a dust
mask when drilling, cutting, or sanding. When drilling or cutting, always check what is on the
opposite side of the surface.
Contact Garmin Product Support if you have any questions while installing or using your
GXM 51. In the USA, go to www.garmin.com/support, or contact Garmin USA by phone at
(913) 397-8200 or (800) 800-1020.
See the Important Safety and Product Information guide in the product box for product warnings and other
important information.
Product Registration
Help us better support you by completing our online registration at www.garmin.com
/registration/.
For future reference, write the serial number assigned to your GXM 51 in the space provided. It
is located on a sticker on the back of the device.
Serial number
In addition to the device serial number, unique ID numbers are associated with your GXM 51.
XM Satellite Radio uses these ID numbers to activate and deactivate your XM weather and
XM audio. To locate the ID numbers on a Garmin NMEA 2000-compliant chartplotter, select
Congure System System Information > > .
For future reference, write the XM WX Weather ID and XM Radio ID assigned to your
GXM 51 in the spaces provided.
XM WX Weather ID
XM Radio ID
November 2009 190-01030-02 Rev. D Printed in Taiwan
2GXM 51 Installation Instructions
Packing List, Accessories, and Tools Needed
Before installing your unit, conrm that your package includes the following items. If any parts
are missing, contact your Garmin dealer immediately.
Standard Package
GXM 51 Antenna
Surface-mount bracket
Pole-mount bracket
Under-deck mount bracket
Mounting hardware (screws and adhesive
pads)
NMEA 2000 T-connector
NMEA 2000/audio cable 19 ft., 8 in. (6 m)
Audio adapter cable 1 ft. (30.5 cm)
Installation instructions
Optional Accessories
Additional NMEA 2000 network
components
Audio adapter cable extensions
•
•
•
•
•
•
•
•
•
•
•
Tools Needed
Drill
Drill bits—
1
/
8
in. (3 mm) and
3
/
4
in.
(19 mm)
Hole saw, 1 in. (25 mm)—surface-mount
cable hole
Screwdriver—surface-mount screws
Pencil (to mark surface-mount pilot holes)
Countersink bit (when mounting on
berglass)
Marine sealant (for some mounting
options)
•
•
•
•
•
•
•
Step 1: Mount the GXM 51 Antenna
You can surface mount the GXM 51 antenna, attach it to a standard 1 in. OD pipe-threaded-pole
marine mount (14 threads-per-inch—not included), or even install the antenna under berglass.
Select a suitable location for the GXM 51
antenna on your boat. To ensure the best
reception, mount the GXM 51 antenna in a
location that has a clear, unobstructed view of
the sky in all directions.
Avoid mounting the GXM 51 antenna
where it is shaded by the superstructure of
the boat, a radome antenna, or a mast.
On a sailboat, avoid mounting the GXM 51
antenna high on the mast.
The GXM 51 antenna provides more-stable
reception when located nearer to water
level.
Mount the GXM 51 antenna at least 3.3 ft. (1 m) away from (preferably above) the
path of any radar beam or a VHF radio antenna.
Temporarily secure the antenna in the preferred mounting location and test it for correct
operation. If you experience interference with other electronics, try a different location. After
verifying correct operation, permanently mount the antenna.
•
•
•
•
SS BARNETT
Radar VHF Radio Antenna
3 ft.
(1 m)
Above - best
Below - OK
EMI (Electromagnetic Interference)
from engine components
Best
Better
Good
EMI
GXM 51 Placement Considerations
SS BARNETT
Radar VHF Radio Antenna
3 ft.
(1 m)
Above - best
Below - OK
EMI (Electromagnetic Interference)
from engine components
Best
Better
Good
EMI
GXM 51 Placement Considerations
GXM 51 Installation Instructions 3
Surface-mounting the GXM 51 Antenna
1. Use the surface-mount bracket as your mounting template.
Use a pencil to mark the three screw locations on the surface and to trace the cable hole
in the center of the bracket.
Set the surface-mount bracket aside. Do not drill through the surface-mount bracket.
2. Drill three 1/8 in. (3 mm) pilot holes.
Note: If you are mounting the GXM 51 on berglass, it is recommended to use a countersink
bit to drill a clearance counterbore through the top gelcoat layer (but no deeper). This will help to
avoid cracking in the gelcoat layer when the screws are tightened.
3. Use a 1 in. (25 mm) hole saw to cut the cable hole in the center.
4. Use the included M4 screws to attach
the surface-mount bracket to the
mounting surface.
5. Route the NMEA 2000/audio cable
through the 1 in. (25 mm) cable hole
and connect it to the GXM 51.
6. Make sure the large gasket is in
place on the bottom of the GXM 51
antenna, place the antenna on the
surface-mount bracket , and twist it ➊
clockwise to lock it in place .➋
7. Secure the antenna to the mounting
bracket with the included M3 set
screw .➌
8. Route the NMEA 2000/audio cable
away from sources of electronic interference, and connect it to your NMEA 2000 network
and to the audio input of your stereo receiver (see ).page 5
Pole Mounting the GXM 51 Antenna
With the pole-mount adapter attached to the GXM 51, you can install the GXM 51 on a
standard 1 in. OD pipe-threaded-pole marine mount (14 threads per inch—not included). You
can route the NMEA 2000/audio cable either through the pole or outside the pole.
To mount the GXM 51 with the cable routed outside the pole:
1. Route the NMEA 2000/audio cable through the pole-mount adapter, and place the cable in
the vertical slot along the base of the pole-mount adapter.
2. Thread the pole-mount adapter onto a standard 1 in. OD pipe-threaded-pole marine mount
(14 threads per inch—not included). Do not overtighten the adapter.
3. Connect the NMEA 2000/audio cable to the
GXM 51 antenna.
4. Place the GXM 51 antenna on the pole-mount
adapter and twist it clockwise to lock it in ➊
place .➋
5. Secure the antenna to the adapter with the
included M3 set screw .➌
6. (Optional) With the GXM 51 installed on the
pole mount, ll the remaining gap in the vertical
cable slot with a marine sealant (not included).
7. Attach the marine mount to the boat if it is not
already attached.
8. Route the NMEA 2000/audio cable away from
sources of electronic interference, and connect
it to your NMEA 2000 network and to the audio
input of your stereo receiver (see ).page 5
•
•
GXM 51
antenna
Surface-mount
bracket
Mounting
surface
➊
➋
➌
Rubber
gasket
GXM 51
antenna
Surface-mount
bracket
Mounting
surface
➊
➋
➌
Rubber
gasket
GXM 51
antenna
Pole-mount
adapter
Vertical cable
slot
➊
➋
➌
GXM 51
antenna
Pole-mount
adapter
Vertical cable
slot
➊
➋
➌

Specyfikacje produktu

Marka: Garmin
Kategoria: Niesklasyfikowane
Model: GXM 51

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Garmin GXM 51, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Garmin

Garmin

Garmin GDT 43 Instrukcja

14 Października 2024
Garmin

Garmin Edge Power Mount Instrukcja

9 Października 2024
Garmin

Garmin Approach Z30 Instrukcja

7 Października 2024
Garmin

Garmin GMM 170 Instrukcja

4 Października 2024
Garmin

Garmin GMR 18 xHD Instrukcja

4 Października 2024
Garmin

Garmin GT30-TH Instrukcja

3 Października 2024
Garmin

Garmin GT51M-TH Instrukcja

2 Października 2024
Garmin

Garmin Panoptix PS60 Instrukcja

1 Października 2024
Garmin

Garmin GPS 17HVS Instrukcja

30 Września 2024
Garmin

Garmin GPSMAP 8015 MFD Instrukcja

30 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024