Instrukcja obsługi Garmin GRID

Garmin Niesklasyfikowane GRID

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Garmin GRID (38 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/38
GRID™
Installation Instructions......................................................... 2
Instructions d'installation....................................................... 4
Istruzioni di installazione....................................................... 6
Installationsanweisungen......................................................8
Instrucciones de instalación................................................11
Instruções de Instalação..................................................... 13
Instruções de instalação..................................................... 15
Installatie-instructies........................................................... 17
Installationsvejledning.........................................................19
Asennusohjeet.................................................................... 21
Installeringsinstruksjoner.................................................... 23
Installationsinstruktioner..................................................... 25
Instrukcja instalacji..............................................................27
Pokyny pro instalaci............................................................ 30
Инструкции по установке..................................................32
Upute za instalaciju.............................................................35
安装说明............................................................................. 37
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GRID
™ is a trademark of Garmin Ltd. or its subsidiaries. These trademarks may not
be used without the express permission of Garmin.
December 2015 190-01557-91_0CPrinted in Taiwan
GRID™ Installation Instructions
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
CAUTION
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
To obtain the best performance and to avoid damage to your
boat, install the device according to these instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin® Product Support.
Registering Your Device
Help us better support you by completing our online registration
today.
• Go to .http://my.garmin.com
• Keep the original sales receipt, or a photocopy, in a safe
place.
Contacting Garmin Product Support
• Go to for in-country support www.garmin.com/support
information.
• In the USA, call 913-397-8200 or 1-800-800-1020.
• In the UK, call 0808 238 0000.
• In Europe, call +44 (0) 870 850 1241.
Software Update
You may need to update the device software when you install
the device or add an accessory to the device.
Loading the New Software on a Memory Card
1Insert a memory card into the card slot on the computer.
2Go to .www.garmin.com/support/software/marine.html
3Select next to .Download GPSMAP Series with SD Card
4Read and agree to the terms.
5Select .Download
6Select .Run
7Select the drive associated with the memory card, and select
Next Finish > .
Updating the Device Software
Before you can update the software, you must obtain a
software-update memory card or load the latest software onto a
memory card.
1Turn on the chartplotter.
2After the home screen appears, insert the memory card into
the card slot.
NOTE: In order for the software update instructions to
appear, the device must be fully booted before the card is
inserted.
3Follow the on-screen instructions.
4Wait several minutes while the software update process
completes.
5When prompted, leave the memory card in place and restart
the chartplotter manually.
6Remove the memory card.
NOTE: If the memory card is removed before the device
restarts fully, the software update is not complete.
Tools Needed
• Drill and drill bits
• #2 Phillips screwdriver
• Jigsaw or rotary tool
• File and sandpaper
• Marine sealant (optional)
Mounting Considerations
NOTICE
This device should be mounted in a location that is not exposed
to extreme temperatures or conditions. The temperature range
for this device is listed in the product specifications. Extended
exposure to temperatures exceeding the specified temperature
range, in storage or operating conditions, may cause device
failure. Extreme-temperature-induced damage and related
consequences are not covered by the warranty.
This device can be mounted in dashboard or other surface using
the included hardware. When selecting a mounting location,
observe these considerations.
• The device should be mounted in an accessible location. You
must be able to readily access the joystick and buttons to
interact with the assigned navigation device.
• To avoid interference with a magnetic compass, the device
should not be installed closer to a compass than the
compass-safe distance value listed in the product
specifications.
• The location must allow room for the routing and connection
of the cables.
Mounting the Device
NOTICE
Be careful when cutting the hole to flush mount the device.
There is only a small amount of clearance between the case and
the mounting holes, and cutting the hole too large could
compromise the stability of the device after it is mounted.
If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid any cracking in the gel-coat layer when the screws are
tightened.
The included template and hardware can be used to mount the
device at the selected location.
1Trim the flush-mount template and make sure it fits in the
location where you want to mount the device.
2Remove the protective liner from the back of the template
and adhere it to the location where you want to mount the
device.
3Using a 7/16 in. (11 mm) drill bit, drill one or more of the holes
inside the corners of the solid line on the template to prepare
the mounting surface for cutting.
4Using a jigsaw, cut the mounting surface along the inside of
the solid line indicated on the template.
5Place the device in the cutout to test the fit.
2 Installation Instructions
6If necessary, use a file and sandpaper to refine the size of
the cutout.
7After the device À fits correctly in the cutout, make sure the
mounting holes on the device line up with the pilot holes
Á on
the template.
8If the mounting holes on the device do not line up, mark the
new pilot-hole locations.
9Using either a 3/32
in. (2.5 mm) drill bit, or drill bit appropriate
for the mounting surface, drill the pilot holes.
10 Remove the template from the mounting surface.
11 If you will not have access to the back of the device after you
mount it, connect all necessary cables to the device before
placing it into the cutout.
12 Place the device into the cutout.
13 Secure the device to the mounting surface using the included
screws Â.
14 Install the decorative bezel by snapping it in place around the
edges of the device.
Connection and Cable Considerations
• For easier cable routing, the power and Garmin Marine
Network cables are packaged without the locking rings
installed. You should route the cables before you install the
locking rings.
• After connecting a locking ring to a cable, you should make
sure the locking ring is securely connected and the o-ring is
in place so the power or data connection remains secure.
• The device should be connected to the same power source
as the other devices on the same Garmin Marine Network. If
this is not possible, all the devices must be connected to the
same ground.
Connecting the GRID™ to the Garmin Marine Network
The GRID is not compatible with Garmin chartplotters prior to
the GPSMAP® 8000 Series and the GPSMAP 8500.
The GRID does not need to be connected directly to the device
that you plan to control with the GRID. It can be assigned to any
compatible device connected to the same Garmin Marine
Network.
1Connect the GRID to a Garmin device on the Garmin Marine
Network using a Garmin Marine Network cable.
2After the rest of the devices in your Garmin Marine Network
are installed, use the software to assign the GRID to a
compatible Garmin device.
Pairing the GRID Remote Input Device with
the Chartplotter
Before you can use a GRID remote input device with a
chartplotter, you must pair the devices.
You can initiate the paring of the devices from the chartplotter or
from the GRID remote input device.
Pairing the GRID Device with the Chartplotter from
the GRID Device
1On the GRID remote input device, press and at the + HOME
same time.
A selection page opens on all of the chartplotters on the
Garmin Marine Network.
2Rotate the wheel on the GRID remote input device to
highlight on the chartplotter you want to control with Select
the GRID remote input device.
3Press .SELECT
Pairing the GRID Device with the Chartplotter from
the Chartplotter
1Select > > > Settings System Station Information GRID™
Pairing Add > .
2On the GRID remote input device, press .SELECT
Rotating the GRID Joystick
For certain installation situations, you can rotate the orientation
of the GRID joystick.
1Select > > .Settings Communications Marine Network
2Select the GRID device.
GRID Specifications
Specification Measurement
Dimensions (W×H×D) 31/16 × 67/8 × 23/8 in. (77 × 174.8 × 60
mm)
Weight 9.1 oz. (258 g)
Temperature range From 5° to 158°F (from -15° to 70°C)
Material Fully gasketed, high-impact plastic,
waterproof to IEC 60529 IPX7 standards
Input power 10–35 Vdc
Fuse 7.5 A, 42 V fast-acting
Max. power usage at 10
Vdc
2.8 W
Typical current draw at 12
Vdc
100 mA
Max. current draw at 12
Vdc
280 mA
Compass-safe distance 14 in. (356 mm)
Installation Instructions 3

Specyfikacje produktu

Marka: Garmin
Kategoria: Niesklasyfikowane
Model: GRID

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Garmin GRID, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Garmin

Garmin

Garmin GDT 43 Instrukcja

14 Października 2024
Garmin

Garmin Edge Power Mount Instrukcja

9 Października 2024
Garmin

Garmin Approach Z30 Instrukcja

7 Października 2024
Garmin

Garmin GMM 170 Instrukcja

4 Października 2024
Garmin

Garmin GMR 18 xHD Instrukcja

4 Października 2024
Garmin

Garmin GT30-TH Instrukcja

3 Października 2024
Garmin

Garmin GT51M-TH Instrukcja

2 Października 2024
Garmin

Garmin Panoptix PS60 Instrukcja

1 Października 2024
Garmin

Garmin GPS 17HVS Instrukcja

30 Września 2024
Garmin

Garmin GPSMAP 8015 MFD Instrukcja

30 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024