Instrukcja obsługi Fusion EL-F651SPG

Fusion głośnik EL-F651SPG

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fusion EL-F651SPG (10 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/10
®
EL Series Installation Instructions ..................................................................................................... 2
Instructions d'installation des EL Series ............................................................................................6
EL Series Istruzioni di installazione ................................................................................................ 10
EL Series – Installationsanweisungen ............................................................................................ 14
Instrucciones de instalación de los EL Series .................................................................................18
EL Series Instruções de instalação .................................................................................................22
Installatie-instructies voor EL Series ............................................................................................... 26
Garmin®, the Garmin logo, FUSION®, the Fusion logo, and True-Marine™ are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used
without the express permission of Garmin.
April 2018
190-02212-90_0A
EL Series Installation Instructions
Important Safety Information
WARNING
Failure to follow these warnings and cautions could result in
personal injury, damage to the vehicle or vessel, or poor product
performance.
This device must be installed according to these instructions.
Disconnect the vehicle's or vessel's power supply before
beginning to install this product.
CAUTION
Continuous exposure to sound pressure levels over 100 dBA
may cause permanent hearing loss. The volume is typically too
loud if you cannot hear people speaking around you. Limit the
amount of time you listen at high volume. If you experience
ringing in your ears or muffled speech, stop listening and have
your hearing checked.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
It is strongly recommended that you have your audio system
installed by a professional installer to ensure optimum
performance.
You must read all installation instructions before beginning the
installation. If you experience difficulty during the installation, go
to for product support.www.fusionentertainment.com
What's In the Box
• 2 speakers
• 2 tinned, pre-terminated speaker wires (6 m)
• 8 Phillips stainless steel, 4.2 mm x 25.4 mm (8 gauge x 1 in.)
mounting screws
• 2 mounting templates
• 2 grilles
Tools Needed
• Electric drill
• Drill bit (size varies based on surface material)
• Phillips screwdriver
• Wire strippers
• Crimping tool
• Electrical tape
• Appropriate saw or utility knife to cut surface material
• Marine sealant (optional)
NOTE: For customized installations, additional tools and
materials may be needed.
Mounting Considerations
Selecting the correct mounting location is critical to optimize the
performance of each speaker. FUSION® speakers are designed
to perform in the widest possible range of mounting locations,
but the more you plan the installation, the better the speakers'
sound will be.
• For the best performance, you should mount the speakers
higher in the boat. Sound travels in the direction in which the
speakers are facing, so if you mount them in a lower location,
the sound quality and volume may not be not ideal.
• If you intend to mount the speakers outside the boat, you
must mount them in a location well above the waterline,
where they are not submerged or damaged by docks, pilings,
or other pieces of equipment. When mounted correctly, these
speakers are rated IP65 for protection from the front of the
speaker. Water exposure and damage to the rear of the
speaker voids the warranty. This includes situations when the
speakers are mounted in a sealed enclosure, especially if
they are exposed to wash down. On supported models, using
an enclosure with a port or vent exposed to the outside
environment may allow water to collect and damage the
speaker.
• You should select mounting locations that enable you to hear
sound from both speakers at the same time to achieve a
sound stage effect. To achieve this effect, you should not
mount the speakers side-by-side.
• When possible, you should select mounting locations where
the area behind each speaker is enclosed.
• You must select mounting locations that provide sufficient
clearance for the mounting depth of the speakers as
specified in the product specifications.
• For better bass performance, you should select a mounting
locations that provide the appropriate space behind the
speaker according to the optimum enclosure design
requirements in the specifications section. Too small an area
restricts bass, and too large an area compromises bass
performance. Also, mounting a speaker close to an open
area (where sound from the back of the speaker has a very
short path to compete with sound from the front of the
speaker) produces the least bass.
• On supported models, when a speaker is not exposed to the
outside environment, you can achieve a better bass
performance using an enclosure with a ported design. For
supported models, the optimum enclosure design
recommendations in the specifications section include
dimensions for the optimum port size and length.
• You should select a flat mounting surface for the best seal.
• You should protect the speaker wires from sharp objects and
always use rubber grommets when wiring through panels.
• You should select mounting locations that avoid potential
obstacles, such as fuel and hydraulic lines and wiring.
• You should protect all terminals and connections from
grounding and from each other. Failure to do so could result
in permanent damage to the audio system and void the
product warranty.
• To avoid interference with a magnetic compass, you should
not mount the speakers closer to a compass than the
compass-safe distance value listed in the product
specifications.
• You must turn off the audio system before making any
connections to the source unit, amplifier, or speakers. Failure
to do so could result in permanent damage to the audio
system.
Mounting the Speakers
Before mounting the speakers, you must choose a location
following the guidelines above.
Before cutting the mounting surface you should verify that there
is enough clearance for the speaker behind the surface. Refer to
the specifications for clearance information.
1Route the wires from the source to the speaker location,
away from sources of electrical interference.
2Trim the template and make sure it fits in the selected
location.
3Orient the template with the FUSION logo at the bottom of
the template.
4Secure the template to the selected location.
5Using a rotary tool or jigsaw, cut the mounting surface along
the inside of the line on the template.
2 Installation Instructions
6Place the speaker in the cutout to test the fit.
7If necessary, use a file and sandpaper to refine the size of
the cutout.
8After the speaker fits correctly in the cutout, ensure the
mounting holes on the speaker line up with the pilot holes on
the template.
9If the mounting holes on the speaker do not line up, mark the
new hole locations.
10 Using an appropriately sized drill bit for the mounting surface
and screw type, drill the holes.
11 Remove the template from the mounting surface.
12 Connect the speaker wires À while observing polarity.
13 If necessary, connect the LED wires ( ).LED Wiring, page 3
14 Place the speaker in the cutout.
15 Secure the speaker to the mounting surface using the
included screws Á.
NOTE: Do not over tighten the screws, especially if the
mounting surface is not flat.
16 Attach the grille to the speaker front (Attaching the Grille,
page 3).
LED Wiring
Connecting the LED Wires
Before you connect the LED wires, you should determine which
speaker LED color you want to use, and identify the
corresponding speaker wire colors.
Speaker LED Color Speaker Wire Color
Red Red
Green Green
Blue Blue
Yellow Red and green
Magenta Red and blue
Cyan Blue and green
White Red, green, and blue
NOTE: This feature is available only on the sports model
speakers.
You can control the color of the speaker LEDs through the
polarity of the LED wires. You can splice the ground wire to
multiple wires on the LED cable to customize the LED color.
The black wire on the LED cable is terminated with a 4 mm
female bullet connector, and the color wires are terminated with
4 mm male bullet connectors. You can connect these to 4 mm
bullet connectors on your wires (not included), or remove the
bullet connectors to connect to the bare wires instead.
1Connect a positive wire to the black wire on the LED cable.
2Connect a ground wire to the wire on the LED cable
according to the preferred speaker LED color.
3Route the positive and negative wires, and connect them to a
power source (Connecting the Sports Model Speakers LED
Wires to Power, page 3).
Connecting the Sports Model Speakers LED Wires to Power
NOTE: This feature is available on only the Sports model
speakers.
You must connect all 12 Vdc wiring to the LEDs to a 3 A fuse at
the power-source end of the cable. You should connect the
positive (+) power wire to a 12 Vdc power source through an
isolator switch or circuit breaker to turn the speaker LEDs on
and off. You can use the same isolator or circuit breaker
controlling the power supply to your stereo, which allows you to
turn the LEDs and the stereo on and off at the same time.
You should use 20 AWG (0.5 mm2) or thicker wire to connect
the LEDs to the battery.
1Route the positive power (+) and negative ground (-) wires
from the speaker to the battery.
2Connect the negative wire to the negative (-) battery terminal.
3Connect the positive wire to the positive (+) terminal through
a 3 A fuse and isolator switch or circuit breaker.
Attaching the Grille
1With the speakers mounted, hold the grille with the FUSION
logo at the bottom, or at the 6 o'clock position.
2Turn the grille counter-clockwise about 10 degrees, so the
FUSION logo is at the 5 o'clock position.
3Place the grille on the speaker, and twist it clockwise to
secure it.
NOTE: You can press on the grille to snap it into place
instead of twisting it.
Speaker Information
Registering Your EL Series
Help us better support you by completing our online registration
today.
• Go to .www.fusionentertainment.com
• Keep the original sales receipt, or a photocopy, in a safe
place.
Dimension Drawings
Side View
À40 mm (1 37/64 in.)
Á127 mm (5 in.)
A Sports model speaker is shown, but the dimensions are the
same for the Classic model.
Installation Instructions 3

Specyfikacje produktu

Marka: Fusion
Kategoria: głośnik
Model: EL-F651SPG

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Fusion EL-F651SPG, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Fusion

Fusion

Fusion SG-CL65SP Instrukcja

21 Września 2024
Fusion

Fusion XS-F40CWB Instrukcja

20 Września 2024
Fusion

Fusion MS-EL602 Instrukcja

19 Września 2024
Fusion

Fusion XS-F65SPGW Instrukcja

18 Września 2024
Fusion

Fusion XS-FL65SPGW Instrukcja

16 Września 2024
Fusion

Fusion SG-F65W Instrukcja

16 Września 2024
Fusion

Fusion FM-F65RW Instrukcja

16 Września 2024
Fusion

Fusion SG-F772W Instrukcja

16 Września 2024
Fusion

Fusion SG-FL882SPC Instrukcja

16 Września 2024
Fusion

Fusion SG-F88W Instrukcja

16 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024