Instrukcja obsługi Furuno NAVpilot-711

Furuno Niesklasyfikowane NAVpilot-711

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Furuno NAVpilot-711 (100 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/100
AUTOPILOT
NAVpilot-700/711/720
Installation Manual
SYSTEM CONFIGURATION .........................ii
EQUIPMENT LISTS ......................................iii
1. HOW TO INSTALL THE UNITS ............ 1-1
1.1 Control Unit FAP-7001/FAP-7011...... 1-1
1.1.1 Surface mount.......................... 1-2
1.1.2 Desktop mount......................... 1-4
1.2 Processor Unit FAP-7002 .................. 1-5
1.3 Rudder Reference Unit FAP-6112 ..... 1-7
1.4 Remote Controllers (option)............... 1-9
1.5 Distributor FAP-6800 (option) .......... 1-12
1.6 Control Unit FAP-7021 ..................... 1-13
1.7 Cable Extension Kit
FAP-7822 (option)............................ 1-13
2. WIRING.................................................. 2-1
2.1 General Wiring ................................... 2-1
2.2 Processor Unit.................................... 2-2
2.2.1 Connections inside the processor
unit ........................................... 2-2
2.2.2 How to fasten cables to the cable .
clamps...................................... 2-3
2.2.3 How to put wires into the connector
blocks....................................... 2-4
2.2.4 How to terminate of NMEA2000
connection................................ 2-5
2.2.5 Power and motor cables .......... 2-5
2.2.6 Teleflex linear sensor............... 2-7
2.2.7 CAN bus power........................ 2-8
2.2.8 Connection to TB4 ................... 2-8
2.3 Control Unit ........................................ 2-8
2.4 Remote Controllers (option)............... 2-9
2.4.1 Example remote controller
connections............................ 2-10
2.4.2 Prohibited remote controller
connections............................ 2-11
2.5 Input/Output Sentences ................... 2-12
3. INITIAL SETTINGS ............................... 3-1
3.1 About Initial Settings, Menu Operation3-1
3.2 How to Select Language and Units,
Open the Installation Menu ................ 3-2
3.3 Display Setup ..................................... 3-4
3.4 Ship’s Characteristics Menu............... 3-5
3.5 Dockside Setup Menu ........................ 3-6
Dockside setup for RRU..................... 3-6
Dockside setup for Fantum
FeedbackTM ..................................... 3-15
3.6 CAN bus Port Setup......................... 3-17
3.7 NMEA0183 Port Setup..................... 3-18
3.8 Sensor Setup.................................... 3-20
3.9 Universal Port Setup ........................ 3-21
3.10 Sea Trial........................................... 3-23
3.11 Data Calibration................................ 3-25
3.12 PARAMETER SETUP Menu ........... 3-26
3.13 AUTO OPTION Menu....................... 3-30
3.14 NAV OPTION Menu ......................... 3-31
3.15 FISH HUNTER OPTION Menu or
WIND OPTION Menu....................... 3-34
3.15.1FISH HUNTER OPTION
menu ...................................... 3-34
3.15.2WIND OPTION menu............. 3-35
3.16 SYSTEM SETUP Menu.................... 3-36
3.17 RC (Remote Controller) SETUP
Menu ................................................ 3-37
3.18 All Clear............................................ 3-37
JIS CABLE GUIDE ................................. AP-1
PACKING LISTS ........................................A-1
OUTLINE DRAWINGS ...............................D-1
INTERCONNECTION DIAGRAM............... S-1
MOUNTING TEMPLATES
www.furuno.com
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
The paper used in this manual
is elemental chlorine free.
・FURUNO Authorized Distributor/Dealer
9-52 Ashihara-cho,
Nishinomiya, 662-8580, JAPAN
A : JAN 2010
.
Printed in Japan
All rights reserved.
F1 : JUN . 12, 2012
Pub. No. IME-72720-F1
*
00017181315
*
*
00017181315
*
(REFU ) NAVpilot-700/711/720
*
00017181315
*
*
00017181315
*
* 0 0 0 1 7 1 8 1 3 1 5 *
i
WARNING
WARNING
WARNING
WARNING
WARNING
Turn off the power at the switchboard
before beginning the installation.
Fire or electrical shock can result if the
power is left on.
Use the proper power cable.
Use JIS type DPY-2.5 or the equivalent.
Other types can cause fire.
Confirm that no one is near the rudder
when bleeding air from oil cylinder.
The rudder may move unexpectedly,
possibly causing bodily injury.
When connecting a geomagnetism
detection type heading sensor,
correct magnetic field deviation.
If an autopilot is used without the compen-
sation, unexpected course change may
occur.
Set REMOTE CONTROLLER 1/2 on
SYSTEM SETUP menu properly accord-
ing to remote controller connected.
If not done properly, malfunction may
occur. Especially, take care when
setting the NFU-type remote controller.
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
Control
Unit
Standard Steering
compass compass
0.35 m 0.30 m
Confirm that the power supply voltage
is compatible with the voltage rating
of the equipment.
Connection to the wrong power supply
can cause fire or damage the equipment.
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
Separate the reversible pump at least one
meter from communications equipment,
communications antenna and communi-
cations cabling to prevent interference.
Processor Unit
FAP-7002 0.45 m 0.30 m
Remote
controllers 0.30 m 0.30 m
FAP-7001
FAP-7011 0.35 m 0.30 m
FAP-7021 0.35 m 0.30 m
SAFETY INSTRUCTIONS
WARNING
Indicates a condition that can cause death or serious injury if
not avoided.
CAUTION
Indicates a condition that can cause minor or moderate injury if
not avoided.
Warning, Caution Mandatory Action
Prohibitive Action
Please read these safety instructions before you install the equipment.

Specyfikacje produktu

Marka: Furuno
Kategoria: Niesklasyfikowane
Model: NAVpilot-711

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Furuno NAVpilot-711, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Furuno

Furuno

Furuno FI-502 CH Wind Angle Instrukcja

12 Stycznia 2025
Furuno

Furuno 1751 Mark-2 Instrukcja

22 Września 2024
Furuno

Furuno GP-1650WDF Instrukcja

21 Września 2024
Furuno

Furuno GP-33 Instrukcja

16 Września 2024
Furuno

Furuno 1761 Mark-2 Instrukcja

15 Września 2024
Furuno

Furuno DRS2D Instrukcja

15 Września 2024
Furuno

Furuno TZTL15F Instrukcja

15 Września 2024
Furuno

Furuno Verado Instrukcja

15 Września 2024
Furuno

Furuno GP-330B Instrukcja

14 Września 2024
Furuno

Furuno 1761 Mark-3 Instrukcja

14 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

GBC

GBC ThermaBind T500Pro Instrukcja

15 Stycznia 2025
Da-Lite

Da-Lite Parallax 29850 Instrukcja

15 Stycznia 2025
Crivit

Crivit IAN 290909 Instrukcja

15 Stycznia 2025
Tripp Lite

Tripp Lite SmartRack SRW12US Instrukcja

15 Stycznia 2025
Powerfix

Powerfix IAN 280221 Instrukcja

15 Stycznia 2025
AGM

AGM Rattler TC35-640 Instrukcja

15 Stycznia 2025
AGM

AGM Wolf-7 Pro Instrukcja

15 Stycznia 2025
AGM

AGM Anaconda TC50-640 Instrukcja

15 Stycznia 2025
AGM

AGM Secutor Pro TS50-640 Instrukcja

15 Stycznia 2025
Microchip

Microchip AT91SAM9M11 Instrukcja

15 Stycznia 2025