Instrukcja obsługi Frigidaire PLMV169DC

Frigidaire Magnetostrykcja PLMV169DC

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Frigidaire PLMV169DC (8 stron) w kategorii Magnetostrykcja. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

1 MOUNTING SPACE

This Microwave Oven/Hood requires a mounting space on a

wall as shown in Figure 1. It is designed to be used with stan-

dard 12-inch wall cabinets.

p/n 2 316137 34

TINSEB385MRR0

2 WALL CONSTRUCTION

This Microwave Oven/Hood should be mounted against and

supported by a flat vertical wall. The wall must be flat for prop-

er installation. If the wall is not flat, use spacers to fill in the

gaps. Wall construction should be a minimum of 2” x 4” wood

studding and 3/8” or more thick dry wall or plaster/lath. The

mounting surfaces must be capable of supporting weight of 110

pounds—the oven and contents—AND the weight of all items

which would normally be stored in the top cabinet above the

unit.

The unit should be attached to a minimum of one 2” x 4”

wall stud or two 2" x 3" wall studs.

To find the location of the studs, one of the following methods

may be used:

A. Use a stud finder, a magnetic device which locates the nails

in the stud.

B. Use a hammer to tap lightly across the mounting surface to

find a solid sound. This will indicate stud location.

The center of the stud can be located by probing the wall with a

small nail to find the edges of the stud and then placing a mark

halfway between the edges. The center of any adjacent studs

will normally be 16” or 24” to either side of this mark.

Installation

Instructions

Over the Range

Microwave Oven

BEFORE YOU BEGIN

•IMPORTANT – Save these instructions for local

inspector's use.

•IMPORTANT – Observe all governing codes

and coordinates.

•Note to Installer – Be sure to leave these

instructions with the Consumer.

•Note to Consumer – Keep these instruc-

tions for future reference.

•Skill Level – Installation of this appliance

requires basic mechanical and electrical skills.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not cov-

ered under the Warranty.

• Please read all instructions thoroughly before installing

the Over the Range Microwave Oven. Two people are

recommended to install this product.

• If a new electrical outlet is required, its installation

should be completed by a qualified electrician before the

Microwave Oven is installed. See 3 ELECTRICAL

GROUNDING INSTRUCTIONS on page 2.

Read

these instructions completely and carefully.

NEED HELP?

For customers in the United States, call: 1-800-944-9044

For customers in Canada, call: 1-800-213-9397 (English)

1-800-668-4606 ext.8199 (French)

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

Figure 1

66" or more

from floor

Backsplash At least 2"

15.5"

30"

12"

30" or more from

cooking surface

3 ELECTRICAL GROUNDING

INSTRUCTIONS

This appliance must be grounded. This oven is equipped with a

cord having a grounding wire with a grounding plug. It must be

plugged into a wall receptacle that is properly installed and

grounded in accordance with the National Electrical Code and

local codes and ordinances. In the event of an electrical short

circuit, grounding reduces risk of electric shock by providing an

escape wire for the electric current.

WARNING - Improper use of the grounding plug can result in a

risk of electric shock.

ELECTRICAL REQUIREMENTS

The oven is equipped with a 3-prong grounding plug. DO NOT

UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE

GROUNDING PIN FROM THE PLUG.

The Power Supply Cord and plug must be connected to a sep-

arate 120 Volt AC, 60 Hz, 15 Amp, or more branch circuit, sin-

gle grounded receptacle. The receptacle should be located

inside the cabinet directly above the Microwave Oven mounting

location as shown in Figure 2.

NOTE:

1. If you have any questions about the grounding or electrical

instructions, consult a qualified electrician or serviceperson.

2. Neither Electrolux nor the dealer can accept any liability for

damage to the oven or personal injury resulting from failure

to observe the correct electrical connection procedures.

4 HOOD EXHAUST DUCT

When the hood is vented to the outside, a hood exhaust duct is

required. All ductwork must be metal; absolutely do not use

plastic duct. Check that all connections are made securely.

Please read the following carefully:

Exhaust connection: The hood exhaust has been designed to

connect to a standard 3-1/4” X 10” rectangular duct. If round

duct is required, a rectangular-to-round adapter must be used.

Rear exhaust: If a rear or horizontal exhaust is to be used, care

should be taken to align the exhaust with the space between the

studs, or wall should be prepared at the time it is constructed by

leaving enough space between wall studs to accommodate

exhaust.

Maximum duct length: For satisfactory air movement, the total

duct length of 3-1/4” X 10” rectangular or 6” diameter round duct

should not exceed 140 feet.

Elbows, adapters, wall caps, roof caps, etc. present additional

resistance to air flow and are equivalent to a section of straight

duct which is longer than their actual physical size. When calcu-

lating the total length, add the equivalent lengths of all transi-

tions and adapters plus the length of all straight duct sections.

Figure 3 shows the approximate feet of equivalent length of

some typical ductwork parts. Use the values in parentheses for

calculating air flow resistance equivalent, which should total

less than 140 feet.

Installation Instructions

Figure 2

Ground

Receptacle

Opening for

Power Cord

Figure 3

5 TOOLS RECOMMENDED FOR

INSTALLATION

• Phillips Screwdriver

• Electric Drill

• 1/2”, 5/8” and 3/32” Drill Bits

• 1-1/2” Wood Bit or Metal Hole Cutter

(if metal cabinet is used)

• Saw to cut exhaust opening (if needed)

• Protective Drop Cloth for product and range -

you may also use carton for protection

• Scissors

• Pencil

• Measure

• Tape

6 INSTALLATION HARDWARE

The INSTALLATION HARDWARE (items 1 - 8) packed with

the oven should contain the following:

Item Name Quantity

1Wood Screw 5 X 30 mm 6

2Toggle Bolt 3/16 inch 4

3Top Cabinet Screw 5 X 60 mm 2

4Flat Washer 30 mm diameter 2

5Power Cord Hanger 1

6Grommet 1

7Tapping Screw 4 x 12 mm 4

8Exhaust Damper Assembly 1

9Charcoal Filter 1

Installation Instructions

Figure 4

Parts shown not to common scale.

7 PREPARATION OF THE OVEN

1. Open the bottom of the carton, bend the carton flaps back

and tilt the oven over to rest on plastic foam pad. Lift carton

off oven and remove all packing materials, Installation

Instructions, Wall Template, Top Template, Charcoal Filter,

Turntable and Turntable Support; however, DO NOT

REMOVE THE WAVEGUIDE COVER, which is located on

the ceiling in the oven cavity. SAVE THE CARTON AS IT

MAY MAKE INSTALLATION EASIER.

2. CHECK THE OVEN.

Check the oven for any damage, such as misaligned or bent

door, damaged door seals and sealing surfaces, broken or

loose door hinges and latches and dents inside the cavity or

on the door. If there is any damage, do not operate the oven

and contact your dealer or ELECTROLUX AUTHORIZED

SERVICER.

3. Remove and save Screws (A) as shown in Figure 5.

4. Pull the louver away from the unit and set aside.

5. Loosen the two Mounting Screws (D) which secure the

Mounting Plate to the rear side of the oven. Remove the

Mounting Plate. See Figure 6.

Figure 5

Control

Panel

Side

(D)

Mounting

Plate

(D)

Mounting Plate

(A)

Figure 6

(A)

Specyfikacje produktu

Marka:	Frigidaire
Kategoria:	Magnetostrykcja
Model:	PLMV169DC

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Frigidaire PLMV169DC, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Magnetostrykcja Frigidaire

Frigidaire FMOS1746BS Instrukcja

8 Października 2024

Frigidaire FMOS1745BS Instrukcja

3 Października 2024

Frigidaire FMOS1846BW Instrukcja

3 Października 2024

Frigidaire MWTK27FGUF Instrukcja

24 Września 2024

Frigidaire FFCM1155US Instrukcja

22 Września 2024

Frigidaire FGMV173KQ Instrukcja

20 Września 2024

Frigidaire FFCT1278LS Instrukcja

17 Września 2024

Frigidaire FMV156DS Instrukcja

17 Września 2024

Frigidaire GMOS1266AF Instrukcja

16 Września 2024

Frigidaire FFMO1611LW Instrukcja

16 Września 2024

Instrukcje Magnetostrykcja

Najnowsze instrukcje dla Magnetostrykcja

ACP JET19 Instrukcja

15 Stycznia 2025

Whirlpool AMW 594 IX Instrukcja

15 Stycznia 2025

Medion MD 10482 Instrukcja

15 Stycznia 2025

Candy CMG 9523 DB Instrukcja

15 Stycznia 2025

Atag mc 111 f Instrukcja

15 Stycznia 2025

Samsung MG11H2020CT Instrukcja

15 Stycznia 2025

Daewoo KOR 63 MDC Instrukcja

15 Stycznia 2025

Siemens HF 85961 Instrukcja

15 Stycznia 2025

Whirlpool AVM 687 IX RVS Instrukcja

15 Stycznia 2025

Daewoo KOR9GQR Instrukcja

15 Stycznia 2025