Instrukcja obsługi Frigidaire FRP12PTT3R

Frigidaire klimatyzacja FRP12PTT3R

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Frigidaire FRP12PTT3R (20 stron) w kategorii klimatyzacja. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/20

66129907342 (Dec.2010)

SAFETY CONSIDERATIONS

Recognize safety information. This is the safety-alert symbol . When you see this symbol on the unit

and in instructions or manuals, be alert to the potential for personal injury.

Understand these signal words: DANGER, WARNING, and CAUTION. These words are used with the

safety-alert symbol. DANGER identifies the most serious hazards which will result in severe personal injury

or death. WARNING signifies hazards which could result in personal injury or death.

CAUTION is used to identify unsafe practices which may result in minor personal injury or product and

property damage. NOTE is used to highlight suggestions which will result in enhanced installation,

reliability, or operation.

! WARNING

PERSONAL INJURY AND/OR PROPERTY DAMAGE HAZARD

Failure to follow this warning could result in personal injury, death and/.or property damage.

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,

electric shock, or to prevent property damage, personal injury, or loss of life.

l This unit must be properly installed in accordance with the Installation Instructions before it is used.

l Immediately repair or replace all electric service cords that have become frayed or otherwise

damaged.

l Unplug or disconnect the unit at the fuse box or circuit breaker before making any repairs.

!WARNING

NOTE: We strongly recommend that any servicing be performed by a qualified professional.

GENERAL INFORMATION

Frigidaire package terminal air conditioners and heat pumps pro vide a high standard of quality in performance,

workmanship, durability and appearance as they heat and cool the occupied air space year round.

This manual provides information for ease of installation, operation and maintenance.

All models are designed for through--the--wall installation. Separate installation instructions are included

with all accessory components.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT: Save these instructions for local inspector's use.

IMPORTANT: Observe all governing codes and ordinances.

NOTE TO INSTALLER

Be sure to leave these instructions with the owner.

NOTE TO OWNER

Keep these instructions for future reference. Be sure to write down the model and serial number on the

space provided on the product registration card. The model and serial number can be located on the serial

number plate attached to the unit. These numbers are required for service. (See Fig. 1.)

Fig. 1 – Sample Data Information Plate

Warning Outlet:Use on Single Circuit Only

Energy

Performance

Rendement

Energetique

Made in China

FOR SERVICE

CALL

FRIGIDAIRE

1-866-942-1567

SERIAL No.:

DATE: 03/11

IK00700001

PACKAGED TERMINAL

AIR CONDITIONER

MODEL:

ELECTRICAL

VOLTS

COOLING DATA

UL FILE NUMBER:SA33529

PACKAGED CONDITIONER TERMINAL AIR

ELECTROLUX HOME PRODUCTS

Charlotte, NC USA

ENG:

Hz, PH.

BTU-

EER-

AMPS-

WATTS-

ELECTRIC HEATING

BTU-

AMPS-

WATTS-

DESIGN PRESSURE

LOW- PSIG

HIGH- PSIG

R410A- OZ

UNIT FEATURES

This unit has many exciting features which

are different from those found on standard PTAC

models. The owner must be familiar with these

features in order to fully understand the operation and

capability of the unit.

Intelligence Your unit has an on board -- computer

that utilizes real time diagnostics to prolong

the life of your unit. There is an LED indicator on the

control board, behind the front panel, that will flash

an error code if the unit has detected some kind of

fault condition. In many cases, the unit will y

automatically clear the fault condition and continue

operating with no interruption. In some cases, the

Fig. 2

condition cannot be cleared and the unit will require service. In those cases, an “Fx” failure mode will be

displayed on the digital display. For a detailed list of all error codes and “Fx” conditions, see Table 5 (page12) -

Status LED Indicator Definitions for further details.

Memory -- Your unit also has memory. If power is lost, all of the control settings (setpoint,

mode, fan speed, on/off and configuration) are remembered. So when power is restored, the unit will

start back up in the mode (and configuration) it was in, when power was lost.

Quiet Design -- Not only does the unit have 2 fan motors and a tangential blower wheel for

optimum sound, the indoor fan will always run a minimum of 10 seconds before the compressor, to

help reduce the sound of the compressor starting.

Random Compressor estart R-- To help prevent power surges after a power outage ( many PTACs

starting at the same time), the compressor is equipped with a 2 to 3 minute 45 second minute 15

second random restart delay feature. Whenever the unit is plugged in, or power has been restarted, a random

compressor restart will occur to help avoid power surges.

Compressor Protection

-- To prevent short cycling of the compressor and maximize it's life, there is a

random start--up delay of 3 minutes on the compressor and a minimum compressor run time of 3 minutes.

Automatic Room reeze rotectionF P -- This protection feature will automatically ensure the indoor

temperature does not fall below freezing. When your PTAC is configured for freeze protection (which is

the default condition), then whenever power is supplied to the unit, if the unit senses

temperature below 40°F, the fan motor and electric heater are turned on and will warm the room to 50°F.

Freeze protection can be switched off (please see page 9), change the configuration switch to turn the

feature off (see section on unit configuration).

Automatic Quick Warm-- p (for heat pump models only)U -- If the room temperature falls to 5°F

below the set point temperature, the reverse cycle heat is shut off and the electric strip heat is turned on

for one cycle, until room temperature rises.

Fan C

onfigure for Optimization of Selected Application -- The unit can be optimized to selected

application by configuring the fan to run in continuous mode or cycle on and off with the compressor and

electric heater (can be different for both heating and cooling modes). In cycle mode, fan will continue to the

run after the compressor or electric heater stops in order to blow off any residual heat or cool left on coil.

Dual-8 Display and LED Display

-- Two 8-segment nixie tubes, 13 LED indicators (They are HIGH,

MED, LOW, AUTO, COOL, FAN, HEAT, ON/OFF, SETOPINT, INDOOR, STATUS and TIMER)

1. Mode indicator display: When the air conditioner operates in a certain mode, the

corresponding mode indicator will be lit;

2. The ON/OFF indicator is in green when the controller is ON and in red when controller is OFF.

3. Fan speed display: When air conditioner operates at high, medium, low or auto fan speed, the

corresponding indicator will be lit.

4. Dua -8 display: Ambient temperature can also be displayed in coolinlg and heating modes through

setting the . Under cooling or heating mode, the dual-8 will display the sekeypad t temperature

(the dual-8 will display indoor ambient temperature under fan mode).

5. If the display data has three bits, the dual-8 will display “ten's digit”+ “unit's digit” at first and

then display “BLANK”+ “hundred's digit”.

Specyfikacje produktu

Marka:	Frigidaire
Kategoria:	klimatyzacja
Model:	FRP12PTT3R

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Frigidaire FRP12PTT3R, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje klimatyzacja Frigidaire

Frigidaire FFRA052WA1 Instrukcja

10 Października 2024

Frigidaire FHPC082AB1 Instrukcja

7 Października 2024

Frigidaire FAC102P1A Instrukcja

7 Października 2024

Frigidaire CPA093DU1 Instrukcja

6 Października 2024

Frigidaire FFPH1422T1 Instrukcja

6 Października 2024

Frigidaire FFRE1233Q1 Instrukcja

4 Października 2024

Frigidaire FHWH184WB2 Instrukcja

3 Października 2024

Frigidaire FHWW125WE1 Instrukcja

3 Października 2024

Frigidaire FHWW105WE1 Instrukcja

3 Października 2024

Frigidaire FHWH234WB2 Instrukcja

3 Października 2024

Instrukcje klimatyzacja

Najnowsze instrukcje dla klimatyzacja

LG HS-H076QPA0 Instrukcja

15 Października 2024

Klarstein Vita Pure 2G Instrukcja

15 Października 2024

Gree ETAC-15HP265V20B Instrukcja

15 Października 2024

Qlima P 126 Instrukcja

14 Października 2024

Mitsubishi MSZ-CB22VA Instrukcja

14 Października 2024

Suntec Motion 90+ Instrukcja

14 Października 2024

Fujitsu Airstage ABHA014GTEH Instrukcja

14 Października 2024

Danby DTAC120B1WDB Instrukcja

14 Października 2024

Amana PTC093K35AXXX Instrukcja

14 Października 2024

Amana AMAP121AB-2 Instrukcja

14 Października 2024