Instrukcja obsługi Ford Figo (2010)

Ford Automatyczny Figo (2010)

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ford Figo (2010) (114 stron) w kategorii Automatyczny. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/114

The information contained in this publication was correct at the time of going to print. In the interest of

development the right is reserved to change specifications, design or equipment at any time without

notice and without incurring any obligations. This publication, or part thereof, may not be reproduced nor

translated without our approval. Errors and omissions excepted.

Part Number: 08/2012 20120601095727

Introduction

About This Manual 5...........................................

Symbols Glossary 5.............................................

Replacement Parts

Recommendation 5........................................

At a Glance

At a Glance 7..........................................................

Child Safety

Booster Seats 11....................................................

Child Seats 12.........................................................

Child Seat Positioning 13...................................

Child Safety Locks 14..........................................

Occupant protection

Principle of Operation 15...................................

Fastening the seat belts 18...............................

Using seat belts during pregnancy 19...........

Keys and Remote Controls

General Information on Radio

Frequencies 20..................................................

Programming the remote control 20............

Changing the remote control

battery 21.............................................................

Locks

Locking and Unlocking 22.................................

Engine immobiliser

Principle of Operation 25...................................

Coded keys 25........................................................

Arming the engine immobiliser 25.................

Disarming the engine immobiliser 25...........

Steering Wheel

Adjusting the Steering Wheel 26....................

Audio Control 26...................................................

Wipers and Washers

Windscreen Wipers 28.......................................

Windscreen Washers 28....................................

Rear Window Wiper and Washers 29...........

Adjusting the windscreen washer

jets 29...................................................................

Checking the Wiper Blades 30........................

Changing the Wiper Blades 30.......................

Lighting

Lighting Control 32...............................................

Headlamp Levelling 32.......................................

Front Fog Lamps 33............................................

Hazard Warning Flashers 33............................

Direction Indicators 34.......................................

Interior Lamps 34.................................................

Changing a Bulb 35.............................................

Bulb Specification Chart 38.............................

Windows and Mirrors

Power Windows 40.............................................

Exterior Mirrors 40................................................

Electric exterior mirrors 41.................................

Interior Mirror 41....................................................

Instrument Cluster

Gauges 42...............................................................

Warning Lamps and Indicators 43.................

Information Displays

General Information 46.....................................

Climate Control

Principle of Operation 47...................................

Air Vents 47.............................................................

Manual Climate Control 48..............................

Heated Windows 50...........................................

Table of Contents

Seats

Sitting in the Correct Position 51.....................

Manual Seats 51....................................................

Head Restraints 53..............................................

Rear Seats 53.........................................................

Convenience features

Sun Visors 55.........................................................

Auxiliary Power Points 55..................................

Glove Box 55..........................................................

USB Port 56............................................................

Starting and Stopping the

Engine

General Information 57......................................

Ignition Switch 57.................................................

Starting a Petrol Engine 57...............................

Starting a Diesel Engine 58..............................

Switching Off the Engine 58............................

Fuel and Refuelling

Safety Precautions 59........................................

Catalytic Converter 59........................................

Fuel filler flap 59...................................................

Refuelling 60..........................................................

Fuel Quality - Petrol 60.....................................

Fuel Quality - Diesel 60.....................................

Fuel Consumption 60.........................................

Transmission

Manual Transmission 61....................................

Brakes

Principle of Operation 62..................................

Hints on Driving With Anti-Lock

Brakes 62.............................................................

Parking Brake 63...................................................

Automatic speed limiter

(ASL)

Principle of Operation 64..................................

Load Carrying

General Information 65......................................

Luggage Covers 65..............................................

Driving Hints

General Driving Points 66.................................

Running-In 66........................................................

Driving Through Water 66.................................

Roadside Emergencies

First Aid Kit 67........................................................

Warning Triangle 67.............................................

Status after a collision

Inspecting safety system

components 68................................................

Fuel Cut-Off Switch 68......................................

Fuses

Changing a Fuse 69.............................................

Fuse Labels 69......................................................

Fuse Specification Chart 70.............................

Fuse Box Locations 74........................................

Vehicle recovery

Towing Points 76..................................................

Towing the Vehicle on Four Wheels 76........

Maintenance

General Information 77.......................................

Opening and Closing the Bonnet 77..............

Under Bonnet Overview - 1.2L

Duratec-16V (71PS) - Sigma 79..................

Under Bonnet Overview - 1.4L

Duratorq-TDCi (DV) Diesel 80...................

Table of Contents

Engine Oil Dipstick - 1.2L Duratec-16V

(71PS) - Sigma 81.............................................

Engine Oil Dipstick - 1.4L Duratorq-TDCi

(DV) Diesel 81....................................................

Engine Oil Check 81.............................................

Engine Coolant Check 83..................................

Brake and Clutch Fluid Check 83...................

Power Steering Fluid Check 84.......................

Washer Fluid Check 84......................................

Technical Specifications 85.............................

Vehicle Care

Cleaning the Exterior 88....................................

Cleaning the Interior 89.....................................

Repairing Minor Paint Damage 89.................

Vehicle battery

Battery care 90.....................................................

Jump-Starting the Vehicle 90.........................

Wheels and Tyres

General Information 92......................................

Changing a Road Wheel 92..............................

Tyre Care 97............................................................

Technical Specifications 97..............................

Vehicle identification

Vehicle Identification Number 99..................

Capacities and Specific-

ations

Weights 100............................................................

Dimensions 101......................................................

Table of Contents

ABOUT THIS MANUAL

Thank you for choosing Ford. We

recommend that you take some time to

get to know your vehicle by reading this

manual. The more that you know about it,

the greater the safety and pleasure you

will get from driving it.

WARNING

Always drive with due care and

attention when using and operating

the controls and features on your

vehicle.

Note: This manual describes product

features and options available throughout

the range, sometimes even before they are

generally available. It may describe options

not fitted to your vehicle.

Note: Some of the illustrations in this

manual may be used for different models,

so may appear different to your vehicle.

However, the essential information in the

illustrations is always correct.

Note: Always use and operate your vehicle

in line with all applicable laws and

regulations.

Note: Pass on this manual when selling

your vehicle. It is an integral part of the

vehicle.

SYMBOLS GLOSSARY

Symbols in this handbook

WARNING

You risk death or serious injury to

yourself and others if you do not

follow the instructions highlighted

by the warning symbol.

CAUTION

You risk damaging your vehicle if you

do not follow the instructions

highlighted by the caution symbol.

Symbols on your vehicle

When you see these symbols, read and

follow the relevant instructions in this

handbook before touching or attempting

adjustment of any kind.

REPLACEMENT PARTS

RECOMMENDATION

Now you can be sure that your Ford

parts are Ford parts

Your Ford has been built to the highest

standards using high quality Ford Original

Parts. As a result, you can enjoy driving it

for many years.

Should the unexpected occur and a major

part needs replacing, we recommend that

you accept nothing less than Ford Original

Parts.

The use of Ford Original Parts ensures that

your vehicle is repaired to its pre-accident

condition and maintains its maximum

residual value.

Ford Original Parts match Ford's stringent

safety requirements and high standards

of fit, finish and reliability. Quite simply,

they represent the best overall repair value,

including parts and labour costs.

Introduction

Now it is easier to tell if you have really

been given Ford Original Parts. The Ford

logo is clearly visible on the following parts

if they are Ford Original Parts. If your

vehicle has to be repaired, look for the

clearly visible Ford branding and make sure

that only Ford Original Parts have been

used.

Look for the Ford logo on the

following parts

Sheet metal

•Fenders

•Doors

E120273

Glass

•Rear window

•Side glass

•Windscreen

E89939

Lighting

•Headlamps

•Rear lamps

E120272

Introduction

Instrument panel overview - RHD

Q J

CB H ID F G

MP O N

E154371

Heated rear window switch. See Heated Windows (page 50).A

Hazard warning flasher switch. See Hazard Warning Flashers (page 33).B

Storage tray.C

Direction indicators. See Direction Indicators (page 34). Main beam. See

Lighting Control (page 32).

Instrument cluster. See (page 42). See Gauges Warning Lamps and

Indicators (page 43).

Wiper lever. See Wipers and Washers (page 28).F

Luggage compartment release switch.G

Air vent. See Air Vents (page 47).H

Window demister.I

At a Glance

Driver side storage compartment.J

Lighting control. See Lighting Control (page 32). Front fog lamps. See Front

Fog Lamps (page 33).

Headlamp levelling control. See Headlamp Levelling (page 32).L

Ignition switch. See Ignition Switch (page 57).M

Steering wheel adjustment. See Adjusting the Steering Wheel (page 26).N

Horn.O

Audio control. See (page 26).P Audio Control

Climate controls. See Climate Control (page 47).Q

Audio unit. See separate handbook.R

Engine idle speed after starting

The engine may idle at a higher speed than

normal immediately after starting from

cold. See Starting a Petrol Engine (page

57). See Starting a Diesel Engine (page

58).

Warning lamps and indicators

ABS warning lamp

Airbag warning lamp

Brake system warning lamp

Direction indicator

Door open warning lamp

MIL (Malfunction indicator lamp)

Glow plug indicator

Illumination ON indicator

Ignition warning lamp

Low fuel level warning lamp

Main beam indicator

Oil pressure warning lamp

Front fog lamp indicator

Engine check warning lamp

Water in fuel warning lamp

Engine coolant temperature

warning lamp

At a Glance

Information display

E120230

OdometerA

TripmeterB

Distance to emptyC

Reset buttonD

Press the Reset button to scroll through

the displays. See General Information

(page 46).

Defrosting and demisting the

windscreen

E123452

If necessary use the heated rear window

to defrost or demist the rear window. See

Heated Windows (page 50).

E72507

See Manual Climate Control (page 48).

Cooling the interior quickly

E90451

See Manual Climate Control (page 48).

Locking and unlocking the doors

with the remote control

E122028

UnlockA

LockB

Luggage compartment lid unlockC

Locking the doors

Press button B once.

Unlocking the luggage compartment

lid

Press button C twice within three seconds.

See Locking and Unlocking (page 22).

Adjusting the steering wheel

WARNING

Never adjust the steering wheel

when the vehicle is moving.

At a Glance

E101516

WARNING

Make sure that you fully engage the

locking lever when returning it to its

original position.

E95179

See Adjusting the Steering Wheel

(page 26).

At a Glance

BOOSTER SEATS

WARNINGS

Do not install a booster seat or a

booster cushion with only the lap

strap of the seat belt.

Do not install a booster seat or a

booster cushion with a seat belt that

is slack or twisted.

Do not put the seat belt under your

child’s arm or behind its back.

Do not use pillows, books or towels

to boost your child’s height.

Make sure that your children sit in an

upright position.

Secure children that weigh more

than 15 kilograms but are less than

150 centimetres tall in a booster seat

or a booster cushion.

Booster seat (Group 2)

E70710

We recommend that you use a booster

seat that combines a cushion with a

backrest instead of a booster cushion only.

The raised seating position will allow you

to position the shoulder strap of the adult

seat belt over the centre of your child’s

shoulder and the lap strap tightly across

its hips.

Booster cushion (Group 3)

E68924

Child Safety

CHILD SEATS

E102143

WARNINGS

Secure children that are less than

150 centimetres tall or less than 12

years of age in a suitable, approved

child restraint, in the rear seat.

Original warning according to ECE

R94.01: Extreme Hazard! Do not use

a rearward facing child restraint on

a seat protected by an air bag in front of

it!

Read and follow the manufacturer s’

instructions when you are fitting a

child restraint.

Do not modify child restraints in any

way.

Do not hold a child on your lap when

the vehicle is moving.

Do not leave children unattended

inside your vehicle in a doors closed

condition.

WARNINGS

If your vehicle has been involved in

an accident, have the child restraints

checked by properly trained Ford

approved technicians.

Note: Mandatory use of child restraints

varies from country to country.

A choice of approved child restraints, which

have been specifically tested and

approved for your vehicle are available

from your Dealer.

Child restraints for different mass

groups

Use the correct child restraint as follows:

Baby safety seat

E68918

Secure children that weigh less than 13

kilograms in a rearward facing baby safety

seat (Group 0+) in the rear seat.

Child Safety

Child safety seat

E68920

Secure children that weigh between 13 and

18 kilograms in a child safety seat (Group

1) in the rear seat.

CHILD SEAT POSITIONING

Mass group categoriesSeating positions

IIIIII0+0

22 - 36 kg15 - 25 kg9 - 18 kgUp to 13 kgUp to 10 kg

UF1

Front co-driver seat

(without PAB)

UF1

XXFront co-driver seat

(with PAB)

UUUUURear seat (3 point belt)

XXXXXRear seat (lap belt only)

PAB - Passenger airbag.

X Not suitable for children in this mass group.

U Suitable for universal category child seats approved for use in this mass.

UF¹ Suitable for universal category forward facing child seats approved for use in this

mass group. However, we recommend that you secure children in a government approved

child restraint, in the rear seat.

Child Safety

CHILD SAFETY LOCKS

WARNING

You cannot open the doors from

inside if you have put the child safety

locks on.

E102138

UnlockA

LockB

Turn the key in the rear door rearward to

activate the lock. To deactivate the lock,

turn the key forward.

Child Safety

PRINCIPLE OF OPERATION

E123935

Airbags

WARNINGS

Do not modify the front of your

vehicle in any way. This could

adversely affect deployment of the

airbags.

Original warning according to ECE

R94.01: Extreme Hazard! Do not use

a rearward facing child restraint on

a seat protected by an airbag in front of it!

Wear a seat belt and keep sufficient

distance between yourself and the

steering wheel. Only when you use

the seat belt properly, can it hold you in a

position that allows the airbag to achieve

its optimum effect.

WARNINGS

Have repairs to the steering wheel,

steering column, seats, airbags and

seat belts carried out by properly

trained technicians from Ford authorised

dealerships.

Keep the areas in front of the airbags

free from obstruction. Do not affix

anything to or over the airbag covers.

Do not poke sharp objects into areas

where airbags are fitted. This could

damage and adversely affect

deployment of the airbags.

The airbag may only deploy with the

ignition switch in the on (II) position.

Occupant protection

WARNINGS

Always keep the areas in front of the

airbags free. Never affix anything to

or over these areas.

If you are too close to an inflating

airbag, it could seriously injure you.

Move your seat as far back as

practical to allow room for airbag inflation.

Several airbag system components

get hot after inflation. Do not touch

after inflation.

Fitment of certain accessories e.g.

bull bars or nudge bars may cause

inadvertent or premature

deployment of air bags.

Note: You will hear a loud bang and see a

cloud of harmless powdery residue if an

airbag deploys. This is normal.

Note: Only wipe airbag covers with a damp

cloth.

Your vehicle is equipped with an event data

recorder which is capable of collecting and

storing data during a crash or near crash

event. The recorded information may assist

in the investigation of such an event. To

access this information special equipment

must be directly connected to the

recording modules. Ford does not access

event data recorder information without

obtaining consent unless pursuant to a

court order or where required by law

enforcement, other government authorities

or other third parties may seek access to

the information independent of Ford.

E123936

The airbag is a supplementary restraint

system. It is designed to be used in addition

to seat belts to help protect against head

and chest injuries in certain moderate to

severe frontal collisions.

The airbag system is not visible until it is

activated. The air bag system is designed

to deploy the driver and passenger front

air bags in certain frontal and front angled

collisions.

Occupant protection

Because the system senses crash severity,

some frontal and side collisions will not

inflate the airbags. Front airbags are not

designed to inflate in rollover, rear and low

speed impacts.

The restraint system comprises:

•a driver airbag

•a front passenger airbag

•crash sensors

•an airbag warning lamp

•an electronic control and diagnostic

unit.

Driver and front passenger airbags

Your vehicle is equipped with an air bag for

the driver, located in the steering wheel

and a passenger air bag is located in the

instrument panel above the glove

compartment. The passenger air bag can

be identified by the ‘Airbag mark’

embedded on the airbag cover.

The seat back must be set correctly for the

airbags to be optimally effective. See

Sitting in the Correct Position (page

51). This helps to reduce the risk of injury

from sitting too close to an inflating airbag.

E102125

The driver and front passenger airbags will

deploy during significant frontal collisions

or collisions that are up to 30 degrees from

the left or the right. The airbags will inflate

within a few thousandths of a second and

deflate on contact with the occupants,

thus cushioning forward face/body

movement. During minor frontal collisions,

overturns, rear collisions and side

collisions, the driver and front passenger

airbags will not deploy.

WARNINGS

If the passenger airbag cover shows

signs of having been removed, the

car should be towed to the nearest

Authorised Ford Dealer for repair. Do not

attempt to reinstall the cover. If the vehicle

must be driven then on no account should

there be an occupant in the front

passenger seat.

The airbag(s) and energy

management retractors will activate

only once. Once activated, the

airbags and energy management retractors

will not function again and must be

replaced immediately. The crash sensor

must also be replaced. If the airbag(s) are

not replaced, the un-repaired area will

increase the risk of injury in a collision.

Airbag warning light

E123944

When the ignition switch is turned to

position II, the airbag warning light on the

instrument panel illuminates for

approximately 3 seconds to indicate that

the system is functional.

Occupant protection

If the airbag warning light does not

illuminate, if it stays on or illuminates

intermittently or continuously while driving,

it means there is a malfunction. Have the

system checked by an Authorised Ford

Dealer.

Seat belts

WARNINGS

Wear a seat belt and keep sufficient

distance between yourself and the

steering wheel. Only when you use

the seat belt properly, it can hold you in a

position to achieve its optimum effect.

The wearing of seat belts is required

by law, even when airbags are fitted.

Never use a seat belt for more than

one person.

Use the correct buckle for each seat

belt.

Do not use a seat belt that is slack

or twisted.

Do not wear thick clothing. The seat

belt must fit tightly around your body

to achieve its optimum effect.

Position the shoulder strap of the

seat belt over the centre of your

shoulder and position the lap strap

tightly across your hips.

E123937

The importance of wearing seat belts

Seat belts must be worn by all vehicle

occupants to be properly restrained and

help reduce the risk of injury in a collision.

Wearing a seat belt will:

E123940

•help keep you in the proper position

when the airbags inflate,

•reduce the risk of harm in rollover, side

or rear impact collisions,

•reduce the risk of harm in frontal

collisions that are not severe enough

to activate the airbags,

•reduce the risk of being thrown from

your vehicle.

E123941

FASTENING THE SEAT BELTS

WARNINGS

Insert the tongue into the buckle until

you hear a distinct click. You have

not fastened the seat belt properly

if you do not hear a click.

Do not use a seat belt that is slack

or twisted.

Occupant protection

E74124

E102129

Pull the belt out steadily. It may lock if you

pull it sharply or if the vehicle is on a slope.

Press the red button on the buckle to

release the belt. Let it retract completely

and smoothly.

USING SEAT BELTS DURING

PREGNANCY

E68587

WARNING

Position the seat belt correctly for

your safety and that of your unborn

child. Do not use only the lap strap

or the shoulder strap.

Position the lap strap comfortably across

your hips and low beneath your pregnant

abdomen. Position the shoulder strap

between your breasts, above and to the

side of your pregnant abdomen.

Occupant protection

GENERAL INFORMATION ON

RADIO FREQUENCIES

CAUTIONS

The radio frequency used by your

remote control can also be used by

other short distance radio

transmissions (e.g. amateur radios,

medical equipment, wireless headphones,

remote controls and alarm systems). If the

frequencies are jammed, you will not be

able to use your remote control. You can

lock and unlock the doors with the key.

Check your vehicle is locked before

leaving it unattended. This will

safeguard against any potential

malicious frequency blocking.

Note: You could unlock the doors if you

press the buttons on the remote control

unintentionally.

The operating range between your remote

control and your vehicle varies depending

on the environment.

PROGRAMMING THE REMOTE

CONTROL

A maximum of four remote controls

(Coded Keys) (including the ones supplied

with the vehicle) can be programmed.

E102144

To programme a new remote control:

•Turn the ignition key to position II four

times within six seconds.

•Switch off the ignition. Cluster indicator

flashes to indicate that it is now

possible to programme a new remote

control.

•Press any button on a new remote

control. Cluster indicator flashes as

confirmation. Repeat this last step for

all of your remote controls, including

the original.

•Switch the ignition back on or wait for

ten seconds without programming

another remote control to end remote

control programming. Only the remote

controls which you have just

programmed are now able to lock and

unlock your vehicle.

Re-programming the unlocking

function

You can change the unlocking function so

that pressing the unlock button once

deactivates the central locking and unlocks

the driver s door. Pressing the unlock’

button twice within three seconds also

unlocks the passengers doors.’

E72190

Keys and Remote Controls

In order to re-programme the function,

press and hold the unlock and lock buttons

simultaneously for at least four seconds

with the ignition switched off. The direction

indicators will flash twice to indicate that

the unlocking function has been

successfully re-programmed.

Pressing and holding both buttons

simultaneously for at least four seconds

again will change the function back.

CHANGING THE REMOTE

CONTROL BATTERY

E107998

Make sure that you dispose of

old batteries in an

environmentally friendly way.

Seek advice from your local authority

regarding recycling.

If the range of the transmitter in the key

decreases gradually, the battery (type 3V

CR 2032) should be replaced.

E68726

•Carefully separate the transmitter unit

from the key using a flat object (e.g. a

screwdriver) at the recess on the back.

•Carefully prise out the battery with the

flat object. Fit the new battery between

the contacts with the + sign facing

downwards. Reassemble the

transmitter unit in reverse order.

E68727

•Open the transmitter unit by separating

the retaining clips on the sides with the

flat object.

E68729

•Carefully prise out the battery with the

flat object. Fit the new battery between

the contacts with the + sign facing

downwards. Reassemble the

transmitter unit in reverse order.

Keys and Remote Controls

LOCKING AND UNLOCKING

Manual locking

E122423

Push to lockA

Pull to unlockB

You need to lock all the doors individually

and lock the driver side door with the key.

Central locking

You can only centrally lock the doors if they

are all closed. Central locking can only be

operated from driver door either by the

handle in the bezel or by the remote

control.

Locking and unlocking

confirmation

The direction indicators will flash once

while unlocking the doors using the remote

control.

The direction indicators will flash twice

while locking the doors using the remote

control.

Locking and unlocking the doors

with the key and inner handle

E120298

UnlockA

LockB

E122423

LockA

UnlockB

Locks

Locking and unlocking the doors

with the remote control

E122028

UnlockA

LockB

Luggage compartment lid unlockC

Locking the doors with the remote

control

CAUTION

Do not put metal accessories/other

immobilizer keys with the key bunch.

This may affect the engine

immobilizer function.

Note: Keep each key separate in order to

avoid a starting malfunction.

Remote will not operate at ignition on

position.

Press the appropriate button .once

Unlocking the luggage compartment

lid

Press button twice within three seconds.C

Automatic relocking

NOTE: To prevent the vehicle being left

unlocked inadvertently, central locking will

be reactivated automatically 45 seconds

after the unlock button is pressed, if the

following occurs during the period.

•No door is opened.

•The luggage compartment is not

opened.

•The ignition is not switched on.

WARNING

If a failure in the vehicle's electrical

system, the drivers door can be

unlocked with a key, the boot can be

still access through the folding rear seat

or boot lock (where respective feature

fitted).

Drive away locking

When the vehicle reaches a speed greater

than 7 Km/h, the central locking is

automatically applied.

Note: All the doors to be closed fully for

proper functioning of drive away locking.

Ignition off auto unlock

If the ignition is switched off the vehicle

will unlock automatically.

Vehicle Search

If the remote Lock button is pressed twice

within 0.5 seconds then the vehicle will

give few short flashes to easily identify your

vehicle amongst a group of vehicle.

Crash sensing door unlock

All doors will be automatically unlocked

when an impact causes the airbags to

deploy and following this the hazard

warning flashers will flash.

Luggage compartment

Opening the luggage compartment

The luggage compartment can be opened

either by remote or pressing the luggage

compartment release switch near the

instrument panel.

Locks

E121245

Using the key.

E121246

To unlock/open, turn the key clockwise.

Closing the luggage compartment

WARNING

Close the luggage compartment

properly to prevent it opening while

you are driving.

E89132

A recessed grip is incorporated inside the

luggage compartment lid to facilitate

closing.

Locks

PRINCIPLE OF OPERATION

The engine immobiliser is a theft protection

system that prevents someone from

starting the engine with an incorrectly

coded key.

CODED KEYS

Note: Do not shield your keys with metal

objects. This may prevent the receiver from

recognising your key as a valid one.

Note: Have all of your remaining keys

erased and recoded if you lose a key. Ask

your dealer for further information. Have

replacement keys recoded together with

your existing keys.

If you lose a key, you can obtain a

replacement from your Ford Dealer. If

possible, provide them with the key

number from the tag provided with the

original keys. You can also obtain

additional keys from your Ford Dealer.

ARMING THE ENGINE

IMMOBILISER

The engine immobiliser is armed

automatically a short time after you have

switched the ignition off.

The indicator in the instrument cluster will

flash to confirm that the system is

operating.

DISARMING THE ENGINE

IMMOBILISER

Switching on the ignition disarms the

system if the correct code is recognised.

The indicator forilluminates

approximately three seconds and then

extinguishes.

If the indicator illuminates constantly for

one minute or flashes for approximately

one minute and then repeatedly at irregular

intervals, the system did not recognise the

key code or a system fault is present.

Remove the key and try again.

If the engine does not start, a system

malfunction has occurred. Have the system

checked by an expert immediately.

Engine immobiliser

ADJUSTING THE STEERING

WHEEL

E102147

WARNING

Never adjust the steering wheel

when the vehicle is moving.

Release the locking lever to adjust the

height of the steering wheel.

Return the lever to its original position to

secure the wheel.

See Sitting in the Correct Position (page

51).

AUDIO CONTROL

Select radio, CD or cassette mode on the

audio unit.

The following functions can be operated

with the remote control:

Volume

E153170

Volume up: Press the button on theVOL +

back of the remote control.

Volume down: Press the VOL - button on

the back of the remote control.

Seek

E153171

Move the lever up or down:

Steering Wheel

•In , this will locate the nextradio mode

radio station up or down the frequency

band.

•In CD, MP3, USB and Bluetooth

audio mode, it will select the next or

previous track.

Mode

E153172

Briefly press the button on the side:

•In , this will locate the nextradio mode

pre-set radio station.

•In , this will playMP3 and USB mode

first song of next folder.

Press and hold the button on the side:

•In , this will change the modeall modes

function to AM /FM/CD or

MP3/USB/Bluetooth audio/Aux.

Steering Wheel

WINDSCREEN WIPERS

E124013

Single wipeA

Intermittent wipingB

Normal wipingC

High speed wipingD

Intermittent wiping

Fixed intermittent

E124015

Select the wiper switch to position forB

intermittent wiping.

However wiping delay can be programmed

as follows.

1. Switch on the ignition.

2. Set the wiper switch to intermittent

position.

3. Move the wiper switch to off position

when the wiper comes to park position.

Note: Wiping delay timing will start from

here to until the wiper switch is moved to

position .B

4. Move the wiper back to position forB

the required time delay.

Note: The user programmed timer resets,

when the wiper switch is moved to low/high

speed or when the ignition is switched off.

Variable intermittent

E124014

Select wipe interval with rotary switch: =1

Short time interval. = Extended time6

interval.

WINDSCREEN WASHERS

E72174

WARNING

Do not operate the windscreen

washer for more than 10 seconds or

when the reservoir is empty.

Wipers and Washers

When the button at the end of the lever is

pressed the washer will work in

conjunction with the wiper operating four

times.

Once the wash/wipe cycle is completed,

the wipers will pause and then perform

one more wipe to clear the screen.

REAR WINDOW WIPER AND

WASHERS

E72175

Pull the lever towards the steering wheel.

Washer

E120173

WARNING

Do not operate the washer for more

than 10 seconds at a time, and never

when the reservoir is empty.

Pull the lever fully towards the steering

wheel and hold it to operate the washer.

The washer will operate in conjunction with

the wipers.

The washer jet for the rear window is

located on the central high mount stop

lamp above the rear window.

Note: Avoid dry wiping operation, this will

reduce the wiper rubber life.

ADJUSTING THE WINDSCREEN

WASHER JETS

E73425

The eye ball jets can be adjusted precisely

using a pin.

Wipers and Washers

CHECKING THE WIPER

BLADES

E66644

Run the tip of your fingers over the edge of

the blade to check for roughness.

Clean the wiper blade lips with water

applied with a soft sponge.

CHANGING THE WIPER

BLADES

WARNING

Avoid the contact between wiper

arm and windscreen when the wiper

arm is placed over windscreen

without wiper blade.

Note: Ensure to keep a thick paper or foam

between the wiper arm and windscreen to

avoid scratches.

E102139

E93784

E93785

Wipers and Washers

E93786

Install in the reverse order.

Wipers and Washers

LIGHTING CONTROL

Lighting control positions

E126635

OffA

Side and tail lampsB

HeadlampsC

Front fog lampsD

Rear fog lampsE

Note: To remind you to switch off the

headlamps, a chime will come on when the

driver door is opened with headlamps on.

Welcome lighting

The side repeaters and tail lamps will flash

once when you unlock the doors with the

remote control. Courtesy lamp comes on

if the lamp control is in door mode.

Main/dipped beam

E102128

Pull the lever fully towards the steering

wheel to switch between main and dipped

beam.

Headlamp flasher

E102128

Pull the lever slightly towards the steering

wheel.

HEADLAMP LEVELLING

E102133

Lighting

You can adjust the level of the headlamp

beams according to the vehicle load.

Recommended headlamp levelling switch positions

Control position

Load in luggage

compartment

Load

Rear seatsFront seats

0--1

0--1-2

1.0-31-2

1.5Max31-2

3.0Max-1

FRONT FOG LAMPS

E126656

Switch on the headlamps and pull out the

control switch one position.

The front fog lamps should be used only

when visibility is considerably restricted by

fog, snow or rain.

The indicator light in the instrument cluster

will illuminate, when the front fog lamps

are in use.

HAZARD WARNING FLASHERS

For item location: See At a Glance (page

7).

E124503

Use only in an emergency to warn other

traffic of vehicle breakdown or

approaching danger. Press the switch to

turn on or off.

You can also operate the hazard warning

flashers when the ignition is off.

Note: The hazard warning flashers flash

during emergency braking.

Lighting

DIRECTION INDICATORS

E102191

Move the lever up/down to activate

right/left direction indicators respectively.

During lane changing flick the lever up or

down and the direction indicators will flash

three times.

Sudden increase in the rate of flashing

warns a failed indicator bulb.

INTERIOR LAMPS

Courtesy lamp

E120292

OffA

Door contactB

OnC

If you set the switch to position , theA

courtesy lamp will be off irrespective of

the doors being opened or closed.

If you set the switch to position theB

courtesy lamp turns on during the

following conditions.

High variantMid variantBase variant

Illuminates1

Does not illuminate

Any of the 4 door

open

IlluminatesDoes not illuminate

Luggage compart-

ment open

1 - The illumination will have theatre dimming effect.

If you set the switch to position , theC

courtesy lamp will come on irrespective of

the door condition and ignition switch

position. It will go off automatically after

a short time to prevent the vehicle battery

from discharging. To switch it back on,

switch on the ignition for a short time.

Lighting

Luggage compartment lamp

E120328

The luggage compartment lamp turns on

during the following conditions.

High variantMid variantBase variant

Illuminates

No Luggage

compartment lamp

fitted

No Luggage

compartment lamp

fitted

Any of the 4 door

open

Illuminates

Luggage compart-

ment open

CHANGING A BULB

WARNINGS

Switch the lights and the ignition off.

Let the bulb cool down before

removing it.

CAUTIONS

Do not touch the glass of the bulb.

Only fit bulbs of the correct

specification. See Bulb

Specification Chart (page 38).

Note: The following instructions describe

how to remove the bulbs. Fitting is the

reverse order unless otherwise stated.

Headlamp main and dipped beam

Note: To remove the right hand side

headlamp bulb, detach the coolant

reservoir.

Detach the coolant reservoir

E125296

1. Remove the bolt.

2. Pull the container from the bracket.

Headlamp bulb

Lighting

1. Remove the headlamp cover.

E154463

2. Disconnect the electrical connector.

3. Release the clip.

4. Remove the bulb.

Side lamps

1. Remove the headlamp cover. See

headlamp bulb removal.

E154464

2. Carefully prise out the bulb holder.

3. Remove the bulb.

Front direction indicators

E154465

1. Turn the bulb holder anticlockwise and

remove it.

2. Gently press the bulb into the bulb

holder, turn it anticlockwise and

remove it.

Side repeaters

E120218

1. Carefully prise out the side repeater

assembly.

2. Turn the bulb holder anticlockwise and

pull it out.

3. Remove the bulb.

Rear lamps

1. Open the tailgate.

Lighting

Number plate lamp

E90601

1. Loosen the screws and remove the

lamp.

2. Remove the bulb.

Courtesy lamp

E120231

1. Carefully prise out the lamp.

2. Turn the bulb holder anticlockwise and

remove it.

3. Remove the bulb.

Luggage compartment lamp

E72784

1. Carefully prise out the lamp.

2. Remove the bulb.

BULB SPECIFICATION CHART

Rating (watt)SpecificationBulb

21PY21WFront direction indicator

5P21/5WSide lamp

55/60H4Headlamp

Lighting

Rating (watt)SpecificationBulb

5WYW5Side repeater

55H11Front fog lamp

5P21/5WBrake and parking lamp (rear)

21P21WRear direction indicator

21P21WReversing lamp and rear fog lamp

16W16WCentral high mounted stop lamp

5CW5Number plate lamp

6W6WCourtesy lamp

5W6WLuggage compartment lamp

Lighting

POWER WINDOWS

WARNING

Do not operate the electric windows

unless they are free from obstruction.

Note: If you operate the switches often

during a short period of time, the system

might become inoperable for a certain time

to prevent damage due to overheating.

The power windows can be operated only

when the ignition is switched on.

The front power window can be operated

by the switches located on either of the

door trims (driver door and front passenger

door). To lower or raise the window, press

or pull the power window switch

respectively.

E120219

Manual windows

E120310

To raise/lower the window rotate the

handle.

Note: The rear window cannot be fully

lowered.

EXTERIOR MIRRORS

Folding mirrors

E102162

You can fold back your exterior mirror in

narrow spaces or when the vehicle is

parked to avoid accidental damage to the

mirrors.

Make sure that you fully engage the mirror

in its support when returning it to its

original position.

Windows and Mirrors

WARNING

Do not overestimate the distance of

the objects that you see in the

exterior mirror. Objects seen in the

mirror will appear smaller and further away

than they actually are.

Manual Exterior Mirrors

E123951

Both door mirrors are adjustable from

inside the vehicle.

ELECTRIC EXTERIOR

MIRRORS

E71280

Left-hand mirrorA

OffB

Right-hand mirrorC

E71281

INTERIOR MIRROR

E71272

Dip the mirror to reduce glare when driving

at night.

Windows and Mirrors

Theater dimming

The instrument cluster illuminates

gradually with a theater dimming effect

when the side lamps are switched on.

Fuel gauge

E121144

CAUTION

Check the fuel level prior starting the

journey.

The arrow adjacent to the fuel pump

symbol tells you on which side of your

vehicle the fuel filler cap is located.

The low fuel level warning light illuminates

at approximately 80 kms before the tank

is empty and audible chimes will be heard

to alert you at 80 kms, 40 kms, 20 kms and

at empty respectively. Refuel as soon as

possible.

Tachometer

Indicates the current engine speed.

Speedometer

Indicates the current vehicle speed.

WARNING LAMPS AND

INDICATORS

The following warning lamps and

indicators will come on briefly when you

switch the ignition on to confirm that the

system is operational:

•Brake warning lamp

•Door open warning lamp

•Engine coolant temperature warning

lamp

•ABS warning lamp

•Low fuel warning lamp

•Airbag warning lamp

•PATS

•Engine check warning lamp

•Water in fuel warning lamp

•MIL (malfunction indicator warning

lamp)

If a warning or indicator lamp does not

illuminate when the ignition is switched

on, it indicates a malfunction. Have the

system checked as soon as possible.

ABS warning lamp

If ABS warning lamp illuminates

(with audible chimes) when you

are driving, this indicates a

malfunction. You will continue to have

normal braking (without ABS) but have

this checked as soon as possible.

Airbag warning lamp

If the airbag warning lamp

illuminates when you are driving,

this indicates a malfunction.

Have this checked as soon as possible.

Instrument Cluster

Brake system warning lamp

WARNING

Reduce your speed gradually. Use

your brakes with great care. Do not

step on the brake pedal abruptly.

The brake system warning lamp

illuminates (with audible

chimes) when:

•the parking brake is engaged.

•low brake fluid.

•EBD (Electronic brake force

distribution) failure in ABS equipped

vehicles.

The brake system warning lamp will stay

on until you release the parking brake. If it

illuminates when you are driving, this

indicates a malfunction in one of the brake

circuits. Check the brake fluid level. See

Brake and Clutch Fluid Check (page 83).

WARNING

If the brake system warning lamp

comes on with the ABS warning

lamp, this indicates a malfunction.

Stop your vehicle as soon as it is safe to

do so and have this checked before

continuing you journey.

Door open warning lamp

The door open warning lamp

illuminates (with audible

chimes) if a door or the tailgate

is open, only when engine is running.

MIL

If the malfunction indicator

warning lamp illuminates when

the engine is running, this

indicates a malfunction. If it flashes when

you are driving, reduce the speed of your

vehicle immediately. If it continues to flash,

avoid heavy acceleration or deceleration.

The engine will continue to run but it will

have limited power. Have this checked

immediately.

Ignition warning lamp

If the ignition warning lamp

illuminates (with audible

chimes) when you are driving,

this indicates a malfunction. Switch off all

unnecessary electrical equipment and

have this checked immediately.

Low fuel level warning lamp

If the low fuel level warning lamp

illuminates (with audible

chimes), refuel as soon as

possible. See Gauges (page 42).

Oil pressure warning lamp

CAUTION

Do not resume your journey if the oil

pressure warning lamp comes on

despite the oil level being correct.

Have this checked immediately.

If the oil pressure warning lamp

illuminates (with audible

chimes) when you are driving,

this indicates a malfunction. Stop your

vehicle as soon as it is safe to do so and

switch the engine off. Check the engine oil

level. See (page 81).Engine Oil Check

Instrument Cluster

Engine check warning lamp

If the engine check warning lamp

illuminates when the engine is

running, this indicates a

malfunction. The engine will continue to

run but it will have limited power. Have this

checked as soon as possible.

Front fog lamp indicator

It will illuminate when you switch

the front fog lamps on.

Water in fuel warning lamp

(vehicles with diesel engine)

If the water in fuel warning lamp

illuminates whilst driving

immediately see an Authorised

Ford Dealer to have the water drained from

the fuel filter.

CAUTION

Failure to do so could damage the

vehicle's fuel injection system causing

engine failure.

Note: Such failures are not covered under

warranty repair.

Engine coolant temperature

warning lamp

If it stays on after starting or

illuminates (with audible

chimes) when driving, this

indicates a malfunction. Stop your vehicle

as soon as it is safe to do so and switch the

engine off. Check the coolant level. See

Engine Coolant Check (page 83).

CAUTIONS

Do not resume your journey if it

illuminates despite the level being

correct. Have the system checked by

a properly trained technician immediately.

CAUTIONS

Do not restart the engine until the

cause of overheating has been

resolved.

Glow plug indicator

See Starting a Diesel Engine

(page 58).

Main beam indicator

The main beam indicator

illuminates when you switch the

headlamp main beam on. It will

flash when you use the headlamp flasher.

Illumination ON indicator

The illumination on indicator

illuminates when the side lamps

are switched on.

Direction indicator

The direction indicator will flash

when you use the direction

indicators. A sudden increase in

the rate of flashing warns of a failed bulb.

Instrument Cluster

GENERAL INFORMATION

WARNING

Do not operate the information

display controls when the vehicle is

moving. The driver should at all times

be alert and focus his attention on the road

ahead only.

Note: The information display will remain

on for several minutes after you switch off

the ignition.

Information display

E120230

OdometerA

TripmeterB

Distance to emptyC

Reset buttonD

Press the reset button to scroll through the

displays.

Note: The information display illuminates

when the driver door is opened.

Display definitions

Tripmeter

Note: The maximum value for tripmeter is

9999.9kms and after that it automatically

resets and starts from zero.

The tripmeter can register the mileage of

individual journeys.

Distance to empty

Indicates the approximate distance that

your vehicle will travel on the fuel in the

fuel tank.

Distance to empty display will stay on for

approximately 5 seconds when the igntion

is switched on and then cluster will go back

to the pre-set mode.

Odometer

Note: The maximum value for odometer

measurement is 999,999 kms after that it

automatically resets and starts from zero.

Registers the total mileage of the vehicle.

Reset button

A short press toggles the display between

odometer/trip/distance to empty.

A long press of more than two seconds

resets the trip to zero.

Information Displays

PRINCIPLE OF OPERATION

Outside air

In this mode the climate control system

utilizes outside air.

Cowl filter and wire mesh filter

These filters remove the dust that is

brought in from the outside air through the

cooling and heating system, when the

blower is operated.

Have your dealer replace/clean the filters

as mentioned in the Periodical

maintenance schedule.

Recirculated air

CAUTION

Prolonged use of recirculated air may

cause the windows to mist up. If the

windows mist up, follow the settings

for defrosting and demisting the

windscreen.

The air currently in the passenger

compartment will be recirculated. Outside

air will not enter the vehicle.

Ensure maximum utilization of the

recirculation mode to avoid dust entering

into the passenger compartment and bad

smell entering from outside.

Heating

The purpose of heating is to heat the

interior compartment in cold weather

conditions.

Heating performance depends on the

temperature of the engine coolant.

Air conditioning

The purpose of air conditioning is to cool

the interior compartment.

Air is directed through the evaporator

where it is cooled. Humidity is extracted

from the air to help keep the windows free

of mist. The resulting condensation is

directed to the outside of the vehicle and

it is therefore normal if you see a small

pool of water under your vehicle.

If you use the air conditioning, the fuel

consumption of your vehicle will be higher.

Note: The air conditioning operates only

when the temperature is above 4ºC (39ºF).

General information on controlling

the interior climate

Warming the interior

Direct the air towards your feet. In cold or

humid weather conditions, direct some of

the air towards the windscreen and the

door windows.

Cooling the interior

Direct the air towards your face.

AIR VENTS

E71942

Climate Control

MANUAL CLIMATE CONTROL

Blower

E124410

Off positionA

Temperature control

E124411

Cold side - Blue in colourA

Warm side - Red in colourB

Air distribution control

E124416

WindscreenA

Footwell and windscreenB

Face levelC

Face level and footwellD

FootwellE

Face level, windscreen and

footwell

You can set the air distribution control to

any position between the symbols.

A small amount of air is always directed

towards the windscreen.

Defrosting and demisting the

windscreen

E123452

Steps to be followed:

1. Set air distribution control to

windscreen.

2. Switch off the recirculation mode.

3. Set the temperature control knob to

maximum hot position.

Climate Control

4. Set the blower to maximum speed.

5. Switch on the A/C.

If necessary, switch the heated windows

on in the instrument panel. See Heated

Windows (page 50).

E72507

Ventilation

There are two types of ventilation.

Normal ventilation

Use outside/fresh air mode. Air will flow

from outside through the air vents during

driving with the blower in off position. The

air distribution control mode can be at any

desired position.

Forced ventilation

In this type of ventilation the blower can

be positioned at any speed and the rest

are same as normal ventilation.

Switching the air conditioning on

and off

E124402

Press the button, to switch on/off the A/C.

If you turn the blower off, the air

conditioning will turn off. When you turn

the blower on again, the air conditioning

will come on automatically (if the A/C

switch is in on position).

Switching the recirculated air on

and off

E124407

Press the recirculated air button to switch

on/off.

To use the outside/fresh air switch off the

recirculation mode.

The last setting will be kept in memory,

press the recirculated air button to change

over to the other mode.

Cooling with outside air

E90450

Cooling the interior quickly

E90451

Steps to be followed:

1. Switch on the blower to maximum

speed.

2. Open the windows for 2-3 minutes to

allow the inside hot air to go out.

3. Switch on the A/C and recirculation

mode.

Climate Control

4. Set the temperature control knob to

maximum cold position.

5. Close the windows and set the blower

to 2nd speed or to your convenience.

Heating the interior quickly

E90449

Reducing interior air humidity

E90452

HEATED WINDOWS

Use the heated rear window to defrost or

demist the rear window.

E124041

The heating of rear window will function

only when the ignition Key is in run position

or ON position. Also this has a timer to auto

cut-off the heating of rear window

operation.

The heated rear window switch is located

in the instrument panel.

E124040

Climate Control

SITTING IN THE CORRECT

POSITION

E68595

WARNINGS

Do not adjust the seats when the

vehicle is moving.

Only when you use the seat belt

properly, can it hold you in a position

that allows the airbag to achieve its

optimum effect.

When you use them properly, the seat,

head restraint, seat belt and airbags will

provide optimum protection in the event

of a collision. We recommend that you:

•sit in an upright position with the base

of your spine as far back as possible.

•do not recline the seatback more than

30 degrees.

•adjust the head restraint so that the

top of it is level with the top of your

head and as far forwards as possible,

remaining comfortable.

•keep sufficient distance between

yourself and the steering wheel. We

recommend a minimum of 250

millimetres (10 inches) between your

breastbone and the airbag cover.

•hold the steering wheel with your arms

slightly bent.

•bend your legs slightly so that you can

press the pedals fully.

•position the shoulder strap of the seat

belt over the centre of your shoulder

and position the lap strap tightly across

your hips.

Make sure that your driving position is

comfortable and that you can maintain full

control of your vehicle.

MANUAL SEATS

Moving the seats backwards and

forwards

E102370

Raise the lever to unlock the seat

from track

Seat forward and rearward

movement

Seats

WARNING

Rock the seat backwards and

forwards after releasing the lever to

make sure that it is fully engaged in

its catch.

Adjusting the height of the driver s’

seat

CAUTION

Do not perform seat cushion height

adjustment while driving.

E102371

Pull the lever upward to raise the driver

seat cushion.

Push the lever downward to lower the

driver seat cushion

Adjusting the angle of the

seatback

E102372

To adjust the front seatback, lift the handle

and hold in the fully up position.

Adjust the seatback to the required back

angle then release the adjustment handle.

Slight rocking of the seatback may be

required to ensure engagement.

The handle will return to the downward

position when locked.

Seats

HEAD RESTRAINTS

E75767

Adjusting the head restraint

Adjust the head restraint so that the top

of it is level with the top of your head.

Removing the head restraint

Press the locking buttons and remove the

head restraint.

REAR SEATS

WARNING

Make sure that the seats and the

seatbacks are secured and fully

engaged in their catches.

Folding the seatbacks down

WARNING

When folding the seatbacks down,

take care not to get your fingers

caught between the seatback and

seat frame.

E123947

1. Push the unlock levers.

2. Push the seatback forwards.

Creating a level load floor

WARNING

Make sure the red indicator is not

showing when you engage the seat

in the catches.

Seats

E123948

1. Insert your fingers between the seat

cushion and seatback and fold the seat

cushion forwards.

2. Push the unlock levers.

3. Push the seatback forwards.

WARNING

When folding the seatbacks up,

make sure that the belts are visible

to an occupant and not caught

behind the seat.

E123949

Seats

SUN VISORS

E66493

The sun visors can be released from the

retention clips and swivelled towards the

side window. The sun visor on the front

passenger side also has a mirror in it.

AUXILIARY POWER POINTS

CAUTION

If you use the socket when the engine

is not running, the battery may

discharge.

The power socket can be used to power 12

volt electrical appliances having a

maximum current rating of 10 amperes.

E120275

When connecting to appliances, use only

specified connectors from the Ford

Accessory range or connectors suitable for

use with SAE standard sockets.

Audio jack

Audio jack is provided in the audio panel.

It is used for connecting MP3 players,

iPod's, etc, to the audio system.

E122031

GLOVE BOX

E102199

Card holderA

Coin holdersB

Convenience features

Note: Do not store heavy and bulky items

in the glove box as it may lead to failure of

the glove box securing lock.

USB PORT

The USB port is located inside the glove

box.

Convenience features

GENERAL INFORMATION

General points on starting

If the battery has been disconnected the

vehicle may exhibit some unusual driving

characteristics for approx. 8 kilometres (5

miles) after reconnecting the battery.

This is because the engine management

system must realign itself with the engine.

Any unusual driving characteristics during

this period may be disregarded.

The starter should not be operated for

longer than 10 seconds during each start

cycle. Release the ignition key as soon as

the engine has started. If the engine has

not started, return the ignition key to

position and repeat the startingO

procedure.

If the engine does not start, See Fuel

Cut-Off Switch (page 68).

Starting the engine by towing or

pushing

WARNING

To prevent damage you must not

push or tow start your vehicle. Use

booster cables and a booster battery.

See Jump-Starting the Vehicle (page

90).

IGNITION SWITCH

Ignition switch positions

Position 0

WARNING

Never return the key to the 0 position

when the vehicle is in motion.

Ignition off. When the key is removed from

the ignition switch, the steering column

lock will be activated as soon as the

steering wheel is turned.

Position I

Steering unlocked. Ignition and all main

electrical circuits are disabled. The ignition

key should not be left in this position for

too long to avoid discharging the battery.

Positon II

Ignition switched on, all electrical circuits

operational. Warning and indicator lamps

illuminate. This is the key position when

driving, and must also be selected when

being towed.

Postion III

Starter motor activated. Release the key

as soon as the engine starts.

STARTING A PETROL ENGINE

Note: You can only operate the starter for

a maximum of 10 seconds at a time.

Cold or hot engine

All vehicles

CAUTION

When the temperature is below -10ºC,

switch the ignition on for at least one

second before starting the engine.

This will make sure that the maximum fuel

pressure is established for starting the

engine.

Note: Do not touch the accelerator pedal.

1. Fully depress the clutch pedal.

2. Start the engine.

Starting and Stopping the Engine

If the engine does not start within 10

seconds, wait for a short period and try

again.

If the engine does not start after three

attempts, wait 10 seconds and follow the

Flooded engine procedure.

If you have difficulty starting the engine

when the temperature is below -10ºC,

press the accelerator pedal between ¼ to

½ of its travel and try again.

Flooded engine

1. Fully depress the clutch pedal.

2. Fully depress the accelerator pedal and

hold it there.

3. Start the engine.

If the engine does not start, repeat the

Cold or hot engine procedure.

Engine idle speed after starting

The speed at which the engine idles

immediately after starting will vary

depending on the engine temperature.

If the engine is cold then the idle speed will

automatically be increased.

The idle speed will slowly decrease to the

normal level as the engine warms up.

STARTING A DIESEL ENGINE

Cold or hot engine

Note: When the temperature is below

-10ºC, you may need to crank the engine for

up to 10 seconds. To aid ease of cranking,

turn the ignition key to position II for at least

couple of seconds before starting the

engine. This ensures that maximum fuel

pressure is established.

Note: Continue cranking the engine until it

starts.

Note: You can only operate the starter for

a maximum of 10 seconds at a time.

Switch the ignition on and wait

until the glow plug indicator goes

off.

Note: Do not touch the accelerator pedal.

1. Fully depress the clutch pedal.

2. Start the engine.

3. Repeat this exercise for 3 to 4 times

until the engine cranks properly.

Note: If starting difficulty is experienced at

temperatures below -10ºC, depress the

accelerator pedal 1/4 to ½ of its travel to

assist starting. This should be done only, if

the engine fails to start after several

attempts of cranking as given in the above

steps.

Flooded Engine

Note: Do not depress the accelerator pedal

fully.

1. Depress the clutch pedal fully.

2. Slowly, depress the accelerator fully,

hold it in this position and start the

engine.

3. If the engine does not start repeat this

exercise for 3 to 4 times.

SWITCHING OFF THE ENGINE

Vehicles with a turbocharger

CAUTION

Do not switch the engine off when it

is running at high speed. If you do, the

turbocharger will continue running

after the engine oil pressure has dropped

to zero. This will lead to premature

turbocharger bearing wear.

Release the accelerator pedal. Wait until

the engine has reached idle speed and then

switch it off.

Starting and Stopping the Engine

SAFETY PRECAUTIONS

WARNINGS

Stop refuelling after the fuel nozzle

stops the second time. Additional

fuel will fill the expansion space in

the fuel tank which could lead to fuel

overflowing. Fuel spillage could be

hazardous to other road users.

Do not use any kind of flames or heat

near the fuel system. The fuel system

is under pressure. There is a risk of

injury if the fuel system is leaking.

CATALYTIC CONVERTER

WARNING

Do not park or idle your vehicle over

dry leaves, dry grass or other

combustible materials. The exhaust

will radiate a considerable amount of heat

during use, and after you have switched

the engine off. This is a potential fire

hazard.

Driving with a catalytic converter

CAUTIONS

Avoid running out of fuel.

Do not crank the engine for long

periods.

Do not run the engine when a spark

plug lead is disconnected.

Do not push-start or tow-start your

vehicle. Use booster cables. See

Jump-Starting the Vehicle (page

90).

Do not switch the ignition off when

driving.

FUEL FILLER FLAP

Pull the release lever located in the floor

to the side of front driver seat for opening

the fuel filler flap.

E120174

Turn the cap anti-clockwise to remove.

When the filler cap is removed, a hissing

noise may be heard. This is normal and

should be disregarded.

To close, turn the cap clockwise until it

engages fully.

E120197

Fuel and Refuelling

REFUELLING

CAUTION

Do not attempt to start the engine if

you have filled the fuel tank with the

incorrect fuel. This could damage the

engine. Have the system checked by a

properly trained technician immediately.

FUEL QUALITY - PETROL

Note: Add 1 ml of IFTEX System G with

every litre of Gasoline (Petrol). It is available

at all Ford authorised dealerships.

CAUTION

Do not use leaded petrol or petrol with

additives containing other metallic

compounds (e.g. manganese-based).

They could damage the emission system.

Use minimum 91 octane unleaded petrol

that meets the specification defined by EN

228, or equivalent.

FUEL QUALITY - DIESEL

Note: We recommend that you use only

high quality fuel without additives or other

engine treatments.

WARNING

Do not mix diesel with oil, petrol or

other liquids. This could cause a

chemical reaction.

CAUTION

Do not add kerosene, paraffin or

petrol to diesel. This could cause

damage to the fuel system.

Use diesel that meets the specification

defined by , or equivalent.EN 590

You can use diesel that contains up to 5%

RME (bio diesel).

Prolonged use of supplemental additives

to prevent fuel waxing is not

recommended.

FUEL CONSUMPTION

Length of journey/engine

temperature

Frequent cold starts and short distance

driving leads to considerably increased fuel

usage.

Traffic and road conditions

Slow moving traffic, uphill driving, frequent

sharp bends and rough roads all have an

adverse effect on fuel consumption.

Erratic driving habits

Anticipate hazards ahead and keep a safe

distance from the vehicle in front.

This not only reduces fuel consumption

but also the noise level.

If you have a prolonged wait at a railway

crossing or at traffic lights in built-up areas,

it is advisable to switch off the engine

during this period.

Vehicle load conditions

Driving in a fully laden condition will result

in high fuel consumption.

Vehicle condition

Low tyre pressure or inadequate engine or

vehicle maintenance will also result in

higher fuel consumption.

Fuel and Refuelling

MANUAL TRANSMISSION

WARNINGS

Engage reverse gear only when the

vehicle is stationary.

Do not apply any undue lateral force

to the gear lever when changing from

5th to 4th gear as this could lead to

the inadvertent selection of 2nd gear.

Reverse gear

E99077

Note: The reverse gear should be engaged

only when the vehicle is stationary.

To avoid shiing noises when engaging the

reverse gear, wait approximately three

seconds with the clutch depressed when

the vehicle is stationary.

To select the reverse gear, shi the lever

into the neutral position and then press the

lever fully to the right against a spring

pressure, before pulling rearwards.

Transmission

Driving speed and gear selection

1.2L Petrol

Engine RPM

range

Speed rangeGear

800-20000-151

1100-225015-302

1500-225030-453

1700-225045-604

>1750>605

1.4L Diesel

Engine RPM

range

Speed rangeGear

750-17500-151

1000-200015-302

1400-200030-453

1500-200045-604

>1750>605

PRINCIPLE OF OPERATION

Dual circuit braking system

E71353

WARNING

If a brake circuit fails, you will at first

experience a softer feel to the brake

pedal. You will then need to exert a

greater force on the brake pedal, and make

allowances for increased stopping

distances. Have the braking system

checked by an expert before continuing

your journey. Authorised Ford Dealers are

recommended.

Your vehicle is fitted with a diagonally split,

dual circuit brake system. If a brake circuit

fails, the other remains operational.

Disc brakes

E71354

Wet brake discs result in reduced braking

efficiency. Dab the brake pedal when

driving from a car wash to remove the film

of water.

After leaving a car wash or driving the

vehicle through water, dab the brake pedal

while driving to remove the film of water.

ABS

WARNING

The ABS does not relieve you of your

responsibility to drive with due care

and attention.

The ABS helps you to maintain full steering

and directional stability when you brake

heavily in an emergency, by preventing the

road wheels from locking.

HINTS ON DRIVING WITH

ANTI-LOCK BRAKES

E71355

When the ABS is operating, the brake pedal

will pulse. This is normal. Maintain pressure

on the brake pedal.

The ABS will not eliminate the dangers

inherent when:

•you drive too close to the vehicle in

front of you.

•the vehicle is aquaplaning.

•you take corners too fast.

•the road surface is poor.

Brakes

PARKING BRAKE

Applying the parking brake

E66567

WARNING

Make sure that the parking brake is

applied before you release the lever.

Note: Do not press the release button when

you apply the parking brake.

1. Press the brake pedal firmly.

2. Pull the parking brake lever upwards

to its fullest extent.

Parking on a hill

If you have to park facing uphill, select first

gear and turn the front wheels away from

the kerb. If you have to park facing

downhill, select reverse gear and turn the

front wheels towards the kerb.

Releasing the parking brake

1. Press the brake pedal firmly.

2. Pull the parking brake lever upwards

slightly, press the release button and

push the lever downwards.

Brakes

Specyfikacje produktu

Marka:	Ford
Kategoria:	Automatyczny
Model:	Figo (2010)

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ford Figo (2010), zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Automatyczny Ford

Ford Focus Electric (2012) Instrukcja

3 Kwietnia 2025

Ford Fiesta (2003) Instrukcja

26 Stycznia 2025

Ford F-59 Commercial Stripped Chassis (2025) Instrukcja

15 Stycznia 2025

Ford Ka (2010) Instrukcja

14 Stycznia 2025

Ford Taurus (2008) Instrukcja

14 Października 2024

Ford Bronco Sport (2022) Instrukcja

14 Października 2024

Ford Focus (2007) Instrukcja

12 Października 2024

Ford Fusion Hybrid (2017) Instrukcja

12 Października 2024

Ford Endeavour (2016) Instrukcja

11 Października 2024

Ford Ranger (2001) Instrukcja

10 Października 2024

Instrukcje Automatyczny

Najnowsze instrukcje dla Automatyczny

Honda Jazz Hybrid (2023) Instrukcja

7 Kwietnia 2025

Dodge Challenger SRT (2017) Instrukcja

2 Kwietnia 2025

Audi SQ5 (2024) Instrukcja

26 Marca 2025

Opel Rocks-e (2021) Instrukcja

13 Marca 2025

Aguilar DCB-4PJ Instrukcja

10 Marca 2025

Aguilar DCB-5J Instrukcja

10 Marca 2025

Aguilar DCB-4J Instrukcja

10 Marca 2025

Mercury Mountaineer (1998) Instrukcja

9 Marca 2025

Aguilar AG 4J-HC Instrukcja

9 Marca 2025

Aguilar AG 5J-HC Instrukcja

9 Marca 2025