Instrukcja obsługi Fluke i3000s Flex

Fluke Niesklasyfikowane i3000s Flex

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fluke i3000s Flex (10 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/10
i3000s/i2000 Flex
AC Current Probe
Instruction Sheet
Introduction
The i3000s 24 Flex, i3000s 36 Flex, and i2000 Flex AC Current
Probes (the Probe) are used with oscilloscopes, digital
multimeters, recorders or data loggers. The i3000s probes can
be used to measure AC current up to 3000 A. The i2000 can be
used to measure AC current up to 2000 A. The flexible
measuring head allows current measurements on conductors
that are hard to reach or inaccessible using typical clamp-on
current probes.
The Probes provide a low-voltage (3 V AC for i3000s models,
and 2 V AC for i2000) output that is proportional to the current
being measured. The Probes provide full-scale direct readings
for 30 A, 300 A, and 3000 A when using the i3000s models, and
20 A, 200 A, and 2000 A when using the i2000.
Safety Instructions
A Warning identifies conditions and procedures that are
dangerous to the user. A Caution identifies conditions and
procedures that can cause damage to the Product or the
equipment under test.
 Warning
To prevent electric shock or personal injury:
• Use the Current Probe only as specified in the
operating instructions; otherwise the current
probe’s safety features may not protect you.
• Use the Probes only if qualified.
• Use caution during installation and use of the
Probe; high voltages and currents may be
present in circuit under test.
• Have maintenance performed by only qualified
service personnel.
PN 2560447
March 2006, Rev. 1, 4/17
©2006-2017 Fluke Corporation. All rights reserved.
Specifications are subject to change without notice.
All product names are trademarks of their respective companies.
• Protect the probe against water and humidity.
• Wear protective clothing and gloves as
required.
• Do not install this product on live conductors.
Always de-energize the circuit under test before
installing the flexible measuring head.
• Always inspect the electronics unit, connecting
cable, and flexible measuring head for damage
before using the Probe.
• Do not use the Probe if damaged.
• Always connect Probe to display device before
installing the flexible measuring head.
• Never change batteries while measurement
head is installed on conductor.
• Use only the provided original or specified
accessories.
• Use the Current Probe only as specified in the
operating instructions; otherwise the current
probe’s safety features may not protect you.
• Adhere to local and national safety codes.
Individual protective equipment must be used
to prevent shock and arc blast injury where
hazardous live conductors are exposed.
• CAT III equipment is designed to protect against
the transients in the equipment in fixed
equipment installations, such as distribution
panels, feeders and short branch circuits, and
the lighting systems in large buildings.
Symbols
The following table shows the symbols used on the product
and/or in this manual.
Symbol Description
This product complies with the WEEE Directive marking
requirements. The affixed label indicates that you must
not discard this electrical/electronic product in domestic
household waste. Product Category: With reference to
the equipment types in the WEEE Directive Annex I, this
product is classed as category 9 "Monitoring and Control
Instrumentation" product. Do not dispose of this product
as unsorted municipal waste.
WARNING - RISK OF DANGER.
WARNING. HAZARDOUS VOLTAGE. Risk of electric
shock.
Consult user documentation.
Measurement Category III is applicable to test and
measuring circuits connected to the distribution part of
the building’s low-voltage MAINS installation.
Double Insulated
Do not apply around or remove from uninsulated
hazardous live conductors without taking additional
protective measures.
Conforms to European Union directives.
Conforms to relevant South Korean EMC Standards.
Certified by CSA Group to North American safety
standards.
Specifications
Electrical Characteristics
Measuring ranges
i3000s (24 and 36 Flex)
i2000 Flex
30 A/300 A/3000 A AC, switch
selectable
20 A/200 A/2000 A AC, switch
selectable
Output sensitivity 100 mV/10 mV/1 mV per A
(AC coupled)
Accuracy (at 25 ºC) ±1 % of range (45 Hz to 65 Hz)
Frequency range
i3000s (24 and 36 Flex)
i2000 Flex
10 Hz to 50 kHz (-3 dB typical)
10 Hz to 20 kHz (-1 dB typical)

Specyfikacje produktu

Marka: Fluke
Kategoria: Niesklasyfikowane
Model: i3000s Flex

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Fluke i3000s Flex, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Fluke

Fluke

Fluke ii500 Instrukcja

9 Października 2024
Fluke

Fluke iSee TC01A Instrukcja

9 Października 2024
Fluke

Fluke 438-II Instrukcja

9 Października 2024
Fluke

Fluke T5-1000 Instrukcja

4 Października 2024
Fluke

Fluke CableAnalyzer DSX-8000 Instrukcja

1 Października 2024
Fluke

Fluke TiX885 Instrukcja

29 Września 2024
Fluke

Fluke TiX875 Instrukcja

29 Września 2024
Fluke

Fluke TiX880 Instrukcja

29 Września 2024
Fluke

Fluke TiX870 Instrukcja

29 Września 2024
Fluke

Fluke 700HTH Instrukcja

29 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024