Instrukcja obsługi Fisher & Paykel RF540ADUX4

Fisher & Paykel lodówka RF540ADUX4

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fisher & Paykel RF540ADUX4 (2 stron) w kategorii lodówka. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
INSTALLATION INSTRUCTIONS
NZ AU GB AE HK SG IE EU CN IN
Refrigerator Surround Kit
E402B, RF402B, E442B, RF442B, E522B, RF522B, RF522W, RF522A, RF540A and RF610A models
continued >
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model
and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
1 Check that the internal cabinetry dimensions are correct (see Diagram 1a/b).
2 Unpack the refrigerator as per instructions on carton.
IMPORTANT!
Due to the size of the refrigerator(s), it is essential that assembly of the surround kit be undertaken with a minimum of two able-
bodied persons.
It is important to include adequate venting to the top of the refrigerator, to ensure efficient operation.
The installation of the refrigerator(s) can be at floor level as shown in Diagram 1a or installed above the toe kick board as in
Diagram1b.
Rollers and feet must be fitted.
Refrigerators installed above the toe kit should have a floor base constructed to support the total weight of the loaded
refrigerator(s) placed on it.
The placement of the 16mm MDF or plywood under the refrigerator(s) on either installation type is to allow the fitment of the bottom
trim that covers it. It is optional.
4
GETTING STARTED
This kit is designed to be used with models with a refrigerator height of between: 1695 – 1806mm with curved or flat door styling.
You can find the part number for each installation in Section 2.
To give the most integrated look, the kitchen cabinetry should be flush with the front of the refrigerator door.
Tools required (not included)
No. 2 drill bit – long.
Electric drill.
Phillips screwdriver.
1 x 16mm piece of MDF the same size as the base of the cavity (optional). Not needed if refrigerator is sitting
directly on the floor and not on raised toe kickarea.
Joiner kit (part number 819264) required if joining two refrigerators side by side.
1
REFRIGERATOR SURROUND KIT
E402B
RF402B
E402B
RF402B
E402B
RF402B
E442B
RF442B
E442B
RF442B
E442B
RF442B
E522B
RF522B
RF522W
E522B
RF522B
RF522W
E522B
RF522B
RF522W
RF522A RF540A
RF610A
REFRIGERATOR MODEL 1 X E402B
1 X RF402B
2 X E402B
2 X RF402B
1 X E442B
1 X RF442B
2 X E442B
2 X RF442B
1 X E522B
1 X RF522B
1 X RF522W
2 X E522B
2 X RF522B
2 X RF522W
1 X RF522A
(French door model)
1 X RF540A
1 X RF610A
(French door model)
CAVITY DIMENSIONS (Flush to edge of door) mm mm mm mm mm mm mm mm
AWidth 807 10721467 1557 962 1777 962852
BDepth* 700 700 700 700 700 700 700 700
C 1Height** 1790 1790 1790 1790 1790 1790 1790 1875
C 2Height*** 1806 1806 1806 1806 1806 1806 1806 1891
DAir vent depth 200 200 200 200 200 200 200 200
EAir vent width 502 1162 1252547 657 6571472 767
KIT PART NUMBERS LH RH LH RH LH RH
Brushed Stainless 24371 24372 24373 24375 2437624374 24377 24381 2438024378 24379
Plus Joiner Kit 819264 819264 819264
* Depth is a minimum requirement.
** Height is without 16mm MDF packer.
*** Height is with 16mm MDF packer.
Cavity dimensions above are to be used as dimensions.minimum
A
B
D
E
C
1
Diagram 1a
Refrigerator at floorlevel
B
E
D
A
C
2
Diagram 1b
Refrigerator above toekick
Diagram 1
2
KIT PART NUMBERS AND CAVITY DIMENSIONS TABLE
All dimensions are internal or cavity dimensions.
The refrigerator can be installed:
1 In a cavity with 16mm panel (bottom trim attached), or in a cavity where the product
is at floor level (no bottom trim). (Diagram 1a).
2 In a cavity with a toe kick under the product with the bottom trim fitted to the base
(Diagram 1b).
3 Check whether your fridge has hinges concealed by the front of the fridge door.
For refrigerators / freezers where the hinge is not concealed by the door refer to
spare parts for the correct kit number. 820413 D should list non concealed number kit.
3
BEFORE INSTALLATION
Concealed hinge Non concealed hinge
844144 B 05.16
Before you call for service or assistance ...
Check the things you can do yourself. Refer to the Installation Instructions and your User Guide. Checkthat:
1 Your product is correctly installed.
2 You are familiar with its normal operation.
3 You have read the ‘Troubleshooting’ section at the back of the User Guide.
If after checking these points you still need assistance or parts, please contact your Fisher & Paykel trained and supported service
technician, Customer Care Centre, or contact us through our website www.fisherpaykel.com
!1
FURTHER INFORMATION
9
TRIM INSTALLATION
The bottom trim is designed to cover the front edge of the floor base panel of the
refrigerator. This trim can be installed on a raised toe kick (Diagram 1a) or toe kick
below the refrigerator (Diagram 1b)
Remembering that if this trim is to be used with the refrigerator at floor level the
cavity dimensions will need to have 16mm added to its height to allow for the bottom
trim to be fitted. Note this trim is optional on this type ofinstallation. If used with a
raised toe kick the 16mm packer should be part of the base (Diagram5). Therefore
16mm is not required to be added to the height dimension.
1 If used place the 16mm piece of plywood or with bottom trim fitted into the cavity
(Diagram 5 or 6). Note: the piece should be the same size as the base of the cavity.
2 Remove protective coating film from surround trim.
3 To install the surrounds, first clip in the top surround. Ensure the locator strips at the
rear of the top brackets clip into the rear of the top trim.
4 Clip both side trims into place starting from the front refrigerator edge.
16mm plywood or
MDF board insert
Part of base
Diagram 5
8
SECURE FLOOR STOPS
Two floor stops are supplied to prevent the
refrigerator from being pushed too far back into
the cavity. These are mounted on the base or
floor at a distance of 688mm from the face front
edge of the trim kit.
!0
MOVE INTO CAVITY
If installing two refrigerators/freezers side by side a joiner kit
is required. Refer to these instructions and fit joiner kit before
pushing refrigerator into place, see Diagram 6.
1 Plug refrigerator into electrical socket, run water connection to
refrigerator if required (Ice & Water models only).
2 Gently install refrigerator into cabinetry making sure it is
centred within the surround trim.
3 The front of the refrigerator door should be flush with the front
of the cabinetry to obtain anintegratedlook.
4 Ensure the front levelling feet are adjusted to take the load of
the fridge and keep it in place.
Optional
Diagram 6
5
PARTS SUPPLIED
Top trim (1)
Side trim (2)
Bottom trim (1)
Top trim brackets:
– Single refrigerator kits
(2 brackets)
– Side by Side kits
(3 brackets)
Side trim
centre brackets
(6)
Screw type A:
#8 x 12 Pozi Drive CSK
(26)
Long screws
10 x 75 CSK PH
Part number: SP0207
(2)
Floor stops
Part number: 460912
(2)
Washers
4 x 11 x 1mm
(2)
Side trim brackets
(10)
Side trim brackets
(4)
7
SECURE SIDE TRIMBRACKETS
Locate the ten side trim brackets.
Position five brackets to the left hand side of the
cabinetry and the remaining five brackets to the right
hand side of the cabinetry.
Brackets should be evenly spaced down each side
(see Diagram 3a/b). Secure each of these brackets
with the two screws provided.
Care must be taken to line up the front edge of the
brackets with the leading edges of thecabinetry.
OR
6
SECURE TOP TRIMBRACKETS
Locate the two/three top trimbrackets.
For the side by side refrigerator kits, one bracket is to be
screwed in the top centre of the cabinetry, secure the top
bracket with two of the screws (Type A, #8 x 12 PoziDrive
CSK) (see Diagram 2a).
For all other kits, the two brackets are to be secured on
either side, by two screws which are mounted from the side
(seeDiagram 2b).
Looking at the front of the refrigerator, place the top brackets
on top of the woodencabinetry.
Care must be taken to line up the top front edge of the
brackets with the leading edge of the cabinetry.
Hint: holes should be drilled in the centre of the slot in the
brackets to allow for adjustment. Diagram 2
Diagram 2b
End bracket
Diagram 2a
Centre bracket
OR
Diagram 3bDiagram 3a
150mm
688mm
Diagram 4

Specyfikacje produktu

Marka: Fisher & Paykel
Kategoria: lodówka
Model: RF540ADUX4

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Fisher & Paykel RF540ADUX4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje lodówka Fisher & Paykel

Fisher & Paykel

Fisher & Paykel RF442BRPUX6 Instrukcja

15 Stycznia 2025
Fisher & Paykel

Fisher & Paykel RF610ADUSB7 Instrukcja

8 Października 2024
Fisher & Paykel

Fisher & Paykel RF610ADUSX6 Instrukcja

8 Października 2024
Fisher & Paykel

Fisher & Paykel E440TRT3 Instrukcja

6 Października 2024
Fisher & Paykel

Fisher & Paykel E440TRX3 Instrukcja

6 Października 2024
Fisher & Paykel

Fisher & Paykel E522BLX5 Instrukcja

2 Października 2024
Fisher & Paykel

Fisher & Paykel E442BLX5 Instrukcja

2 Października 2024
Fisher & Paykel

Fisher & Paykel RF610ADJX7 Instrukcja

2 Października 2024
Fisher & Paykel

Fisher & Paykel RD9120WL Instrukcja

1 Października 2024
Fisher & Paykel

Fisher & Paykel E522BLE4 Instrukcja

1 Października 2024

Instrukcje lodówka

Najnowsze instrukcje dla lodówka

Siemens

Siemens KA 58 NP 95 Instrukcja

15 Stycznia 2025
Zanussi

Zanussi ZRB 29 NC8 Instrukcja

15 Stycznia 2025
Amica

Amica FDR2213B Instrukcja

15 Stycznia 2025
Siemens

Siemens KG 33 VX 41 Instrukcja

15 Stycznia 2025
Bauknecht

Bauknecht KRIS 1509A Instrukcja

15 Stycznia 2025
Dometic

Dometic RM 7400 L Instrukcja

15 Stycznia 2025
LG

LG GR-B652YVSK Instrukcja

15 Stycznia 2025
Zanussi

Zanussi ZRB34211XV Instrukcja

15 Stycznia 2025
Hotpoint

Hotpoint HTR15ABRLCC Instrukcja

15 Stycznia 2025
Hotpoint

Hotpoint HTH17BCCRWW Instrukcja

15 Stycznia 2025