Instrukcja obsługi Fisher & Paykel OB60SC6CEX3

Fisher & Paykel piekarnik OB60SC6CEX3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fisher & Paykel OB60SC6CEX3 (12 stron) w kategorii piekarnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/12

OB60NC, OB60SC & OB60SD

models

BUILT-IN OVEN

INSTAL L ATION GUI D E

NZ A U GB IE

590777E 03.1 9

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our

website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

IMPORTANT SAFETY INSTRUCTIONS

To avoid hazard, follow these instructions carefully

before installing or using this appliance.

Please make this information available to the person

installing the appliance - doing so could reduce your

installation costs.

This appliance must be installed and connected to

the mains power supply only by a suitably qualified

person according to these installation instructions and

in compliance with any applicable local building and

electricity regulations. Failure to install the appliance

correctly could invalidate any warranty or liability

claims.

If the power supply cable is damaged, it must be

replaced by the manufacturer, its service agent or

similarly qualified person in order to avoid a hazard.

Isolating switch: make sure this oven is connected

to a circuit which incorporates an isolating switch

providing full disconnection from the power supply in

accordance with the wiring rules.

The oven must be earthed.

Do not use adaptors, reducers or branching devices

to connect the oven to the mains electricity supply, as

they can cause overheating and burning.

The appliance must not be installed behind a

decorative door in order to avoid overheating.

1 SAFETY AND WARNINGS

WARNING!

Electrical shock hazard

Before carrying out any work on the

electrical section of the appliance, it must be

disconnected from the mains electricity supply.

Connection to a good earth wiring system is

absolutely essential and

mandatory.

Alterations to the domestic wiring system must

only be made by a qualified electrician.

Failure to follow this advice may result in

electrical shock or death.

WARNING!

Hot Surface Hazard

Take care - panel edges are sharp.

Failure to use caution could result in injury or

cuts.

WARNING!

Fire hazard

Do not use adapters, reducers, or branching

devices to connect this appliance to the mains

power supply.

Failure to follow this advice may result in

overheating, burning, or fire.

2 PARTS SUPPLIED

3 PRIOR TO INSTALLATION

4 AFTER INSTALLATION

Screws (2) Metal side shelves

fixing nut (2)

the benchtop and oven cavity are square and level, and are the required dimensions.

the installation will comply with all clearance requirements and applicable standards and regulations.

a suitable isolating switch providing full disconnection from the mains power supply is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and

regulations. The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow for this

variation of the requirements).

the isolating switch will be easily accessible to the customer with the oven installed.

there is at least 1.5 m (and not more than 2 m) free length of power supply cable within the cavity for ease of installation and servicing.

the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall.

the oven will rest on a surface that can support its weight.

the height from the floor suits the customer.

you consult local building authorities and by-laws if in doubt regarding installation.

Lower trim kit (for compact models only)

compact models can be installed with a lower trim kit accessory to align the oven with companion products and cabinetry. If installing the lower trim kit accessory, ensure that this is installed

before the appliance.

IMPORTANT!

Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or

excessive condensation, we recommend moisture-proofing the oven cavity.

IMPORTANT!

Please take extra care not to damage the lower trim of the oven during installation. The trim is important for correct air circulation and allows the door to open and close without

obstruction. The manufacturer does not accept any responsibility for damage resulting from incorrect installation.

the oven door can open fully without obstruction.

the power supply cable does not touch any hot metal parts.

the isolating switch is easily accessible to the customer with the oven installed.

you complete the ‘Final checklist’ at the end of the installation.

If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorised Service Centre, Customer Care, or contact us through

our local website listed at the end of this document.