Instrukcja obsługi Fisher & Paykel CleanSmart WL1068P1

Fisher & Paykel pralka CleanSmart WL1068P1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fisher & Paykel CleanSmart WL1068P1 (52 stron) w kategorii pralka. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/52
CLEANSMART CLOTHES WASHER
WL1068P model
INSTALLATION GUIDE/USER GUIDE
NZ AU
3
Safety and warnings 4
Installation instructions 6
Before your first wash 12
Safety features 13
Control panel 14
Wash cycles 17
The CleanSmart™ wash 19
Wash preparation 20
Getting started quickly 23
Wash options 25
Customising a wash cycle 29
Changing pre-set options 31
Caring for your washer 37
Before you call for service 40
Fault codes 42
Troubleshooting 43
Manufacturer’s warranty 48
Customer care 50
CONTENTS
Registration
To register your product visit our website: fisherpaykel.com/register
4
SAFETY AND WARNINGS
! WARNING!
Electrical Shock Hazard
Failure to follow this advice may result in
electrical shock or death.
If you are using an extension cord or a portable
electrical outlet device (eg multi-socket outlet
box), ensure that it is positioned so that it does
not come into contact with water or moisture.
READ AND SAVE THIS GUIDE
When using your clothes washer, follow basic precautions, including thefollowing:
General
zThis product has been designed for personal, family or household use. This product is
not designed for any commercial use. Any commercial use will terminate this products
manufacturers warranty.
zA damaged power cord must be replaced by a Fisher&Paykel trained and supported
service technician or similarly qualified person in order to avoid a hazard. Do not use
the appliance until it has been repaired to avoid a risk of electric shock.
zDo not operate this machine if it has been damaged during transport. Contact your
Fisher&Paykel dealer or Fisher&Paykel trained and supported service technician.
zThis clothes washer is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge,unless they are supervised or given instructions on how to use the
washerby someone responsible for their safety.
zKeep children away from the washer while it is in operation.
zSupervise children to ensure they do not play with the washer or climb inside thedrum.
zThe washer should only be used for washing and rinsing of textiles where this
isindicated on the care label.
zDo not add petrol, dry-cleaning solvents, or other flammable or explosive substances to
the wash water. These substances give off vapours that could ignite or explode.
zDo not wash articles that have been previously cleaned in, washed in, soaked in,
or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive
substances as they give off vapours that could ignite or explode.
zThe lid will be locked for some parts of the wash cycle for safety reasons. It is possible
to open the lid during the cycle under certain conditions. Never force the lid open.
zDo not touch or operate the machine with wet hands or with bare-feet.
zEnsure the installation provides accessibility to the plug or incorporate a switch in the
fixed wiring in accordance with the wiring rules to allow disconnection of the appliance
from the supply after installation.
zRead and follow the detergent manufacturers’ instructions carefully. Instructions on
how to use the detergent will be clearly indicated on the pack. Remember to store your
detergents out of the reach of children.
5
SAFETY AND WARNINGS
MODEL CODE MAX CAPACITY* (KG)
WL1068P 10
*Capacity refers to the maximum dry weight of items the washer can wash at any one time.
zDo not overload your washing machine beyond its rated capacity.
zDo not wash an electric blanket in your washer unless the care label specifically states
it is safe to do so.
zDo not wash curtains in this washer, as sunlight makes them brittle and they may
disintegrate during washing.
zThe only user-removable parts of the washer are the inlet hose(s) and the dispenser
funnels (tops). No other parts are designed to be removed by anyone other than a
Fisher&Paykel trained and supported service technician.
Installation
zFor guidance on how to install your product, please refer to installation instructions
contained in this document.
Water supply requirements:
zInlet water static pressure: Max. 1MPa (145psi), Min. 34kPa (5psi)
zInlet water flow rate at tap: Min. 8 litres /min
zA pressure-reducing valve must be installed if pressure is higher than 1MPa.
zFor optimum wash performance check the supply pressure is within the
recommendedrange.
zNew hose sets provided with the washer should be used to connect the washer to the
water mains. Old hose sets should not be re-used.
zWe recommend the inlet hose(s) are changed every 5 years. WARNING: Failure to do so
may result in a flood and damage to property.
zThe hot water temperature should not exceed 65°C and the cold water temperature
not exceed35°C. Temperatures above these may cause the machine to fault or cause
damage to the machine.
zInstall the machine on a solid and level floor surface ensuring it has at least 20mm
clearance on each side. The washer must not be installed on any textured floor
coverings (eg carpet, rugs).
Disposal
zWhen disposing of the washer, it is recommended that the lid is removed to
avoidchildren getting trapped inside, and that the electrical cable is cut off
close to thewasher.
6
Accessories
Check if you received the following accessories with your Fisher&Paykel washer. Youwill
find them inside the drum or attached to the packaging.
z2 x inlet hose(s)
z1 x drain hose guide
Unpacking
To ensure the best performance from your new washer please follow the instructionsbelow.
Removing the packaging
1 Remove the outer packaging.
2 Tilt the machine backwards and walk it off the base
packer one foot at a time (ensure the lid is still taped
down).
3 Remove the base packer from under the machine
bypulling it out the front.
4 Remove the tape, lift the lid and remove the bowl
packer from the bowl.
5 Remove the hoses and accessories.
6 Keep the base packer and bowl packer in case they
are required for future transit.
Ensure that the base packer has been removed before operating your machine.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
7
Product dimensions
PRODUCT DIMENSIONS MM
A Overall height of product (to highest point on console) 1060 – 1090
B Overall height of product lid open 1440 – 1470
C Overall width of product 685
D Overall depth of product 700
E Height of product to top of lid closed* (measured at
front of product)
950-980
Standpipe or spigot height 850 – 1200
MINIMUM CLEARANCES MM
F Minimum cavity width 725
G Minimum depth clearance (incl. inlet hoses and drain hose) 750
H Minimum clearance to wall or adjacent product# 20
I Minimum clearance at the rear of the product 50
*The exact height of your washer is dependent on how far the feet are extended from the base of
the washer.
#Applies either side.
PROFILE VIEWFRONT VIEW
A A B
C
F
D
g
e
h I
INSTALLATION INSTRUCTIONS
10
Pull hose
through
guide
Flex hose
guide apart
Standpipe 850 – 1200 mm
(20 mm)
maximum
Fitting the drain hose guide
SPARE PARTS* PART NO.
Hose inlet long (2m) 422680P
Hose inlet large bore 426123P
Drain hose extension (not suitable for attaching to a spigot) 425627P
*Available from your Fisher&Paykel dealer or a Fisher&Paykel trained and supported
service technician.
Draining
To prevent siphoning the drain hose should not extend more than 20mm from the end of
the guide. The height of the standpipe or tub should be between 850 – 1200mm. The drain
hose can be trimmed to length.
zRegularly check that your standpipe or tub is free from lint or other obstructions, which
may affect how your washer works or may cause flooding.
zIn multi-storey apartments or any upper floor, the washer should be installed on a floor
equipped with a drain.
zDraining must comply with local by-laws.
zWe recommend replacing the inlet hoses every 5 years. Hoses should be checked from
time to time and replaced if any wear, cuts, bulges, kinks or leaks are found.
Electrical connection
zThis appliance must be supplied with a 220 – 240V, 50Hz, sinusoidal,
10Aelectrical supply.
Placing the drain hose in a standpipe or tub:
1 Carefully pull the drain hose out from the
back of the washer by pulling the exposed
part of the hose downward and outward.
2 To guide the drain hose over the tub or
standpipe the hose guide MUST be fitted to
the drain hose.
3 Place the drain hose in the tub or standpipe.
Do not fit the hose to a drain spigot. Drainage
must not be airtight in order to prevent
siphoning.
INSTALLATION INSTRUCTIONS
11
Completing the installation
zTurn on the water and check all hose connections for leaks. Ensure there are no kinks in
the hoses. Check the hose connections for leaks again after 24hours.
zUncoil power cord, remove and discard the plastic pin cover, and plug into wall socket.
zConnect the appliance to an earthed outlet protected by a fuse of suitable capacity.
Installation test cycle
Your washer must be correctly installed before use. Check the installation and operation of
the washer using the following procedure:
If there are any problems, you must address these before proceeding with normal use.
The washer will automatically turn off at the end of the cycle if there are no problems.
1 Touch to activate your washer.
3 Touch to start the installation test cycle.
The display will show .
The washer will beep to signal the end of
the installation test cycle. Any faults will be
displayed on the screen, refer to ‘Fault Codes’.
If you need further assistance, please contact a Fisher&Paykel trained and supported
service technician or our Customer Care Centre.
2 Touch both and for 3 seconds.OPTIONS
+
12
BEFORE YOUR FIRST WASH
CleanSmartcapacity
CleanSmart™ offers a very generous 10 kg capacity. The list below outlines what is included
in a 10kg wash load (in accordance with AS / NZS 2040.1:2005).
The above load composition is indicative only. We recommend for everyday use that you
separate out your sheets and towels and wash them separately on the SHEETS and TOWELS
cycle.
WASH LOAD - 10 KG QUANTITY
Sheets (double) 4
Bath towels 8
Tablecloths 3
Shirts 4
T-Shirts 6
Pillowcases 6
Shorts 6
Washcloths 4
Handkerchiefs 2
Check you have done everything you need to before you start your first wash:
Has the basepacker been removed?
Is the drain hose threaded through the hose guide ‘Ubend’ (with no more than 20
mm extended) and hooked into your standpipe or tub, or attached toa spigot?
Is the hot hose connected to the hot valve marked ‘H’?
Is the cold hose connected to the cold valve markedC’?
Have the taps been turnedon?
Is the washer correctly levelled, feet are extended and cabinet corners are clear of
the floor?
Has the power cord been connected to an appropriate power supply andthepower
turned on?
Have you performed the installation test cycle (see previous page)?
13
SAFETY FEATURES
Lid lock
The lid of your CleanSmart™ washer is locked for some parts of the wash cycle, ensuring
safety for you and your family while it is operating.
The LID LOCKED light (above the button) will illuminate when the lid lock is activated,
letting you know if you can open the lid or not.
To unlock the lid at any time during the cycle touch .
If the lid is left open, your CleanSmart™ washer will be unable
to lock the lid, and the cycle will be halted. The washer will
beep to alert you and display a warning message on the
screen. If this occurs, ensure that the lid is closed and touch .
Do not put anything down the lid lock slot in the top deck of
your washer.
Do not try to disable the lid lock.
Auto drain
zUnsupervised clothes washers filled with water can present a drowning hazard to small
children. In order to minimise any risk of this type of accident, your CleanSmart™ has
been pre-programmed to know when this potential hazard is created and drains the
wash water to a safe level.
zIf you pause your CleanSmart™ at any time during the wash cycle when there is water
in the bowl, the machine will activate the AUTO DRAIN function after 3 minutes. This will
drain the water in the wash bowl to an acceptable level, minimising any potential hazard.
z A warning message will be displayed on the digital display while AUTO DRAIN is in
operation. The cycle can be restarted at anytime by touching .


Specyfikacje produktu

Marka: Fisher & Paykel
Kategoria: pralka
Model: CleanSmart WL1068P1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Fisher & Paykel CleanSmart WL1068P1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje pralka Fisher & Paykel

Instrukcje pralka

Najnowsze instrukcje dla pralka