Instrukcja obsługi Festo PAML-CP-90-HP3-G114

Festo Niesklasyfikowane PAML-CP-90-HP3-G114

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Festo PAML-CP-90-HP3-G114 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
PAML-CP/-MB/-MK-90
Sub-base/Mounting bracket/Module connector
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Deutschland
+49 711 347-0
www.festo.com
Assembly instructions
8161942
2021-10b
[8161944]
Translation of the original instructions
© 2021 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product
è www.festo.com/sp.
2 Safety
2.1 Safety instructions
–Only use the product in its original condition without unauthorised modifica-
tions.
–Only use the product if it is in perfect technical condition.
–Take the weight of an individual device or a service unit into account.
Dependent on the design, a mounted service unit can weigh more than 50 kg.
–Under intended use the surface temperature may reach 60 °C. Allow the device
to cool down before working on it.
–Make sure the mounting surface is sufficiently strong for the maximum forces.
–Only use suitable mounting components.
–Mount the individual device or the service unit only on flat surfaces.
2.2 Intended use
–The sub-base PAML-CP serves as an adapter for the pneumatic connection and
for pipe mounting for in-line installation of service units.
–The mounting bracket PAML-MB is used for connection and wall mounting of
individual devices or service units.
–The module connector PAML-MK is used to connect two service units of the
same size.
2.3 Training of qualified personnel
Work on the product may only be carried out by qualified personnel who can eval-
uate the work and detect dangers. Personnel must have the relevant mechanical
training.
3 Additional Information
–Accessories è www.festo.com/catalogue.
4 Product Range Overview
4.1 Scope of delivery
2
1
3
4
5
Fig. 1: Sub-base PAML-CP-90-HP3-G12
1
Front plate (1x)
2
Rear plate (1x)
3
Screw (8x)
4
Washer (8x)
5
O-ring (2x)
6
7
8
Fig. 2: Sub-base PAML-CP-90-HP3-G114
6
Front plate (1x)
7
Rear plate (1x)
8
O-ring (2x)
9
10
11
12
13
141516
Fig. 3: Mounting bracket PAML-MB-90-HP3
9
Wall bracket (1x)
10
O-ring (1x)
11
Front plate (1x)
12
Screw (2x)
13
Rear plate (1x)
14
Sleeve (2x)
15
Screw (2x)
16
Retaining screw (1x)
17
18
19
20
Fig. 4: Module connector PAML-MK-90-HP3
17
Screw (2x)
18
Front plate (1x)
19
O-ring (1x)
20
Rear plate (1x)
4.2 Not in scope of delivery
21
22
Fig.5
21
Electrical pressure regulator (1x)
PREL-90
22
Branching module (1x)
PMBL-90
5 Assembly
Some O-rings will be left over with some mounting variants.
5.1 Mounting the connecting plates PAML-CP
Size G1/4 … G1
2
1
4
5
3
Fig.6
1. Orient the front plate and the rear plate so that the stamp number of1 2
the sub-base corresponds to the stamp number on the housing (1 to 1 and
2 to 2).
2. Insert the O-rings in the slots provided.5
3. Position the front plate and the rear plate .1 2
4. Fasten the front plate and the rear plate to the service unit using four1 2
screws and four washers . Tightening torque: 12 Nm ± 10% 3 4
5. Comply with the maximum screw-in depth for the pipe connection.
ISO 228 Max. screw-in depth [mm]
G1/2 12
G1/3 14
G1/2 16
G1 18
Size G1 1/4
7
6
17
18
19
20
Fig.7
1. Orient the front plate and the rear plate so that the stamp number of6 7
the sub-base corresponds to the stamp number on the housing (1 to 1 and
2 to 2).
2. Insert the O-rings or in the slots provided.8 aI
3. Position the front plate and the rear plate .6 7
4. Fasten the front plate and the rear plate to the service unit using theaH bJ
screws . Tightening torque: 12 Nm ± 10% aG
5. Observe the maximum screw-in depth for the pipe connection in accordance
with ISO 228: 20 mm
5.2 Mounting the mounting brackets PAML-MB
Always mount an individual device with two mounting brackets. Mount a service
unit with a mounting bracket at both the beginning and the end of the service unit
string and between the individual service units.
The grid width for he filter PFML-90 is 135 mm.
Fasten all required wall brackets with two M8 screws each at the specified9 bD
locations. The standard grid width between the wall brackets is 90 mm, and9
the distance in height between holes is 145 mm. All retaining screws mustaF
point upwards.
9
10
11
12
13
14
15
16
24
7
6 8
Fig.8
1. Orient the front plate 6 7 and the rear plate so that the stamp number of
the sub-base corresponds to the stamp number on the housing (1 to 1 and
2 to 2).
2. Insert the O-rings in the slots provided.8
3. Position the front plate and the rear plate .6 7
4. Push the screws into the front plate .aB aA
5. Place the seals between the service units.aJ
6. Place the front plate and rear plate in the slots of the service units.aA aC
7. Screw the screws into the rear plates . Tightening torque: 10 Nm ± 10% aB aC
8. Unscrew the retaining screws .aF
9. Position the service unit combination with the lugs in the slots of the wallaE
brackets .9
10. Tighten the retaining screws . Tightening torque: 2 Nm ± 10% aF
5.3 Assembly of the module connector PAML-MK
23 17
18
19
20
Fig.9
1. Note the flow direction from 1 to 2. The numbers on the product housing bC
serve as orientation.
2. Insert the retaining screws through the holes in the front plate .aG aH
3. Place the seal between the service units.aI
4. Place the front plate and rear plate in the slots of the service units.aH bJ
5. Tighten the screws . Tightening torque: 10 Nm ± 10% aG
6 Disassembly
1. Depressurise the system.
2. Check the surface temperature of the device. If necessary, let the device cool
down.
3. Remove the existing service unit string.
7 Technical data
PAML -CP -MB -MK
Operating pressure [MPa] 0 … 5
[bar] 0 … 50
[psi] 0 … 725
Temperature of medium [°C] +5 … +60
Ambient temperature [°C] +5 … +60
Tab. 1: Technical data

Specyfikacje produktu

Marka: Festo
Kategoria: Niesklasyfikowane
Model: PAML-CP-90-HP3-G114

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Festo PAML-CP-90-HP3-G114, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Festo

Festo

Festo MUC-25 Instrukcja

9 Października 2024
Festo

Festo DAMH-L8-20-PL-1 Instrukcja

9 Października 2024
Festo

Festo EHAM-H1-20-L2-80 Instrukcja

9 Października 2024
Festo

Festo EAHF-E24-60-P-S Instrukcja

9 Października 2024
Festo

Festo DADG-D-F8-16/20 Instrukcja

9 Października 2024
Festo

Festo EAHM-E15-60-E22 Instrukcja

9 Października 2024
Festo

Festo ELGT-BS-160-1000-20P Instrukcja

9 Października 2024
Festo

Festo SMBS-1 Instrukcja

9 Października 2024
Festo

Festo SMBS-2 Instrukcja

9 Października 2024
Festo

Festo EAHH-P2-60 Instrukcja

9 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024