Instrukcja obsługi Extron USB Plus Matrix Controller

Extron Niesklasyfikowane USB Plus Matrix Controller

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Extron USB Plus Matrix Controller (12 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
1
USB Plus Matrix Controller • Setup Guide
The Extron® USB Plus Matrix Controller is a pre-congured controller that can easily be setup and deployed to control Extron
USBExtenderPlus products in a USB Matrix switching application within a gigabit Ethernet network. Quick and easy setup of
the USBPlusMatrixController, USB Extender Plus transmitters and receivers is done using Extron Product Conguration Soft-
ware (PCS). An Extron Control System or any third party control can interface with the USB Plus Matrix Controller via Ethernet or
RS-232 to perform USB switching.
The main components in a USB Extender Plus Matrix system:
• USB Plus Matrix Controller — The controller is pre-congured to control the USB Extender Plus transmitters and receivers
in a USB Matrix switching application. The default Telnet port is 22123 (see the for full USB Plus Matrix Controller Help File
details).
• USB Plus Extenders (transmitters and receivers) — At least 1 transmitter and 1 receiver are required, and up to 64
extenders total may be included. Each extender must be assigned a unique IP address (DHCP cannot be used to assign
these addresses), and these addresses are uploaded to the USB Plus Matrix Controller. All twisted pair models are supported:
rack mountable models (standard and HID-only), AAP™ models, and decorator-style models (see the USB Extender Plus
Series User Guide, available on www.extron.com, for more information about these models).
• Product Configuration Software (PCS) — This free software is loaded on the computer and is used to congure the
USB Extender Plus transmitters and receivers. It is also used to create a conguration that is uploaded to the USB Matrix
Controller (see the for details on how to use PCS with the USB Matrix Controller).USB Plus Matrix Controller Help File
• Extron Toolbelt — This free software is used to congure the IP settings of the USB Matrix Controller (see the Toolbelt Help
File at www.extron.com for details on how to use Toolbelt).
Installation
ATTENTION:
• Installation and service must be performed by authorized personnel only.
• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.
• Do not perform a Mode 5 reset (see to the USB Matrix Controller. Doing so will USB Plus Matrix Controller Help File)
erase the factory loaded conguration used to control the USB Extender Plus transmitters and receivers.
• N’effectuez aucune réinitialisation complète de système (mode 5) (voir sur l’USB USB Plus Matrix Controller Help File)
Matrix Controller. Cette action entraînera en effet la suppression de la conguration par défaut, utilisée pour le contrôle
des émetteurs et récepteurs USBExtenderPlus.
The following diagram shows an example of a USB Plus Matrix Controller system setup:
USB EXTENDER Plus R
CONF IG
PAIR
ST USAT
LIN K
HOS T
1
3
2
4
Rx 1
USB EXTENDER Plus R
CONF IG
PAIR
ST USAT
LIN K
HOS T
1
3
2
4
Rx 2
USB EXTENDER Plus R
CONF IG
PAIR
ST USAT
LIN K
HOS T
1
3
2
4
Rx 3
USB EXTENDER Plus R
CONF IG
PAIR
ST USAT
LIN K
HOS T
1
3
2
4
Rx 4
LAN
Tx
1
USB EXTENDER Plus T
S USTAT
LIN K
HOS T
CONF IG
PAIR
Tx
2
USB EXTENDER Plus T
S USTAT
LIN K
HOS T
CONF IG
PAIR
Tx
3
USB EXTENDER Plus T
S USTAT
LIN K
HOS T
CONF IG
PAIR
Tx
4
USB EXTENDER Plus T
S USTAT
LIN K
HOS T
CONF IG
PAIR
USB Matrix Controller
Control System
SIS (Simple I n t C )nstructio Se ommands
a
t
COM
RT S
CT S
T x
Rx
R
USB PL US MATRI X
C
C
o
t
n
t
ro
l
l
S
S
y
t
s
t
em
r
t
rix
C
ontrolle
r
S
I
S
(S
im
p
le sIn
t
Control
Figure 1. Application Diagram of the USB Plus Matrix Controller System
USB Plus Matrix Controller • Setup Guide (Continued)
2
General Setup for the USB Extender Matrix System
1. Enable the Network Pairing feature on each USB Extender transmitter and receiver to be used in the USB Matrix system.
2. Use Extron Toolbelt to congure the IP settings of the USB Matrix Controller (IP, Subnet, and Gateway addresses).
NOTE: USB Extender Transmitters and Receivers must be on a static IP. Do not configure the extenders for DHCP
mode.
3. Use PCS software and the included 9-pin to 2.5 mm TRS serial cable to sequentially congure each of the IP settings of the
USB Extenders via the Cong port of the product and create a USB Matrix Conguration.
4. Use PCS software to upload the conguration of the USB matrix setup to the USB Plus Matrix controller.
5. Set up an (Extron) control system to control the matrix switching by making input and output ties. Use an Extron IPL control
driver, available on the .Extron website
Setup Requirements
The following are required for the USB Plus Matrix system setup:
• Download Toolbelt and PCS from the Extron website —
• The computer running Toolbelt and PCS to congure the USB Matrix must be on the same Subnet and Gateway.
• USB Extenders Plus (applies to all extenders in the system) —
• Must have a IP address (see the ).unique USB Plus Matrix Controller Help File
NOTE: USB Extender Transmitters and Receivers must be on a static IP. Do not configure the extenders for DHCP
mode.
• Over network pairing must be enabled (see the ).USB Extender Plus T/R User Guide
• Must be on the as the controller and all other USB extenders in the system.same subnet and gateway
• Must have the as all other USB Extender Plus in the system.same firmware
• USB Plus Matrix Controller —
• Must use Extron Toolbelt to congure the IP, Subnet and Gateway address.
• Must be on the same subnet and gateway as the extenders.
• Must have an admin password assigned.
• Control System —
• An Extron or third party control system is required to interface and control the USB Matrix Controller to make and break
ties between the USB Extender Plus transmitters and receivers.
• USB Plus Matrix Controller driver is available on the Extron website.
Hardware Setup
To connect the devices:
1. Connect the USB Plus Matrix Controller to the network via the LAN (TCP) RJ-45 port (see gure2,
2).
POWER
12V
0.2A MAX
GTx Rx
RTS CTS
C O M
USB PLUS MATRIX
LAN / PoE
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
2222
1111
Figure 2. USB Plus Matrix Controller Rear Panel
2. Connect power to the USB Plus Matrix Controller (see gure2, 1) and to the rst USB extender that you will be conguring.
CAUTION: The wires must be kept separate while the power supply is plugged in. Remove power before wiring.
ATTENTION : Les deux cordons d’alimentation doivent être maintenus séparés lorsque la source d’alimentation est
branchée. Coupez l’alimentation avant d’effectuer un raccordement.
ATTENTION:
Do not connect power to the switcher until you have read the ATTENTION notices on page12.
Ne branchez pas l’alimentation au sélecteur avant d’avoir lu les mises en garde ATTENTION aux page12.
3. Connect one of the USB transmitters and receivers to the computer via the Cong port (see gure3,
1) using the included
9-pin to 2.5 mm TRS serial cable.
NOTE: Figure 3 shows the transmitter models only. However, on each receiver the Config port is at the same location as
on the equivalent transmitter model.
PO
WER
--
A MAX
CO
NFI
G
U
S
B EXTENDER PLU
S
D T
POWER
12V
--A MAX
PAIR
CONFIG
USB EXTENDER PLUS D T
11
POWER
12V
--A MAX
PAIR
HOST LINK
CONFIG
11
11
USB Extender Plus T/R (Rack-mountable), Fr
ont Panel
USB Extender Plus T/R AAP, Rear Panel
USB Extender Plus T/R D
(Decorator-Style llplate),Wa
Rear Panel
USB EXTENDER Plus T
S TUSTA
LINK
HOST
CONFIG
PAIR
Figure 3. Config Port Locations on the Three USB Extender Plus Models
Software Setup
PCS and Toolbelt are available free of charge from the . Use PCS software to congure the USB extenders and Extron website
upload their IP addresses to the USB Plus Matrix Controller controller. Use Extron Toolbelt to congure the IP settings of the USB
Matrix Controller (see the for details).USB Plus Matrix Controller Help File
Dowloading the software
To obtain PCS and Toolbelt from the Extron website:
1. Go to www.extron.com. On the main page, click the tab (see gure4, 1).
Figure 4. Download Page on Extron Website
2. To download PCS, click (2) in the left panel of the screen.
3

Specyfikacje produktu

Marka: Extron
Kategoria: Niesklasyfikowane
Model: USB Plus Matrix Controller

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Extron USB Plus Matrix Controller, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Extron

Extron

Extron DTP T UWP 4K 232 D Instrukcja

9 Października 2024
Extron

Extron FOX Matrix 7200 Instrukcja

9 Października 2024
Extron

Extron EWB 210 Series Instrukcja

9 Października 2024
Extron

Extron EDID 101D Instrukcja

9 Października 2024
Extron

Extron FMR 206 Instrukcja

9 Października 2024
Extron

Extron EWB Series Instrukcja

9 Października 2024
Extron

Extron IR Sensor Instrukcja

9 Października 2024
Extron

Extron AVEdge 100 Instrukcja

9 Października 2024
Extron

Extron MLM 100 AAP Instrukcja

9 Października 2024
Extron

Extron MAAP 100 Instrukcja

9 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024