Instrukcja obsługi Extron TLP Pro 725T
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Extron TLP Pro 725T (4 stron) w kategorii monitor. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
TLP Pro 725T Series and
TLP Pro 1025T Series • Setup Guide
Overview
The TLP Pro 725T series are 7-inch tabletop capacitive touchscreens with a resolution of 1024x600 and 24-bit color depth. The
TLP Pro 1025T series are 10-inch tabletop capacitive touchscreens with a resolution of 1280x800 and 24-bit color depth.
All these models can be placed on any convenient at surface.
This guide provides instructions for experienced installers to install these touchpanels. For complete instructions, see the
TLPPro 725 and TLP Pro 1025 Series User Guide, at www.extron.com.
Setup Checklist
Get Ready
Download and install the latest version of the following software:
GUI Designer — for designing layouts for Extron TouchLink® Pro touchpanels and third party touch interfaces.
Global Configurator® Professional Global Configurator Plusor — for setting up and conguring the control processor
and touchpanel.
Toolbelt — provides device discovery, device information, rmware updates, and conguration of network settings,
system utilities, and user management for TouchLink Pro devices.
Global Scripter® — provides an integrated development environment for Extron control systems programming.
NOTE: All four software programs are available from www.extron.com.
Obtain the following network information from your network administrator:
DHCP status (on or off). If DHCP is off, you must also obtain:
IP address Subnet mask Gateway
User name — this can be either or .
Password — by default this is (for either admin or user).
Make a note of the touchpanel MAC address.
Mount and Cable All Devices
ATTENTION:
• Do not power on the touchpanels or control processors until you have read the ATTENTION in the “Base” section of
the or the .TLP Pro 725 and TLP Pro 1025 Series User Guide IPCP Pro User Guide or IPL Pro User Guide
• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section «Base » du
TLP Pro 725 and TLP Pro 1025 Series User Guide IPCP Pro User Guide or IPLProUserGuide ou du .
Mount the units. There are several mounting options for TouchLink Pro touchpanels (see on the next page).Mounting
Connect the touchpanel to a Power over Ethernet injector (not provided). Extron recommends the XTP PI 100 power injector,
which can be purchased separately.
Connect the power injector to the LAN and power it on.
Set up the Touchpanels for Network Communication
Connect the PC that you are using for setup, the control processor, and touchpanel .to the same Ethernet subnetwork
Use the (see page 4) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask, Setup Menu
gateway, and related settings for the touchpanel.
Configure the Touchpanels
The , the , and the GUI Designer Help File Global Configurator Help File Toolbelt Help File provide step-by-step instructions
and more detailed information. The includes an introduction to the software and sections on Global Configurator Help File
how to start a project and conguration. Global Scripter provides an Extron-exclusive Python library (ControlScript®) and
Global Scripter modules to get you started.
1
Product Category
IMPORTANT:
Go to for the
complete user guide and installation
instructions befor
e connecting the
pr
oduct to the power sou
rce.
www.extron.com
Mounting
The base allows these touchpanels to be placed on any suitable at surface.
For additional security, the touchpanels can be attached to a table or desktop.
1. Connect an Ethernet cable to the LAN/PoE input (see , figure 3 F, on the next page) and run the cable through the cable
guide (D).
2. Drill two holes through the desktop from underneath, 3.07” (78 mm) apart
3. Attach the touchpanel with two #8-32 screws through the desktop from underneath into the two mounting holes in the base
of the unit (A).
The touchpanels can also be mounted with the optional Extron SMA-2 swivel mount adapter, which allows them to be secured
to the table and swivel up to 180° in either direction. Attach the SMA-2 to the mounting holes in the base (
A) and follow the
instructions in the .SMA-2 Swivel Mount Adapter Kit User Guide
Front Panel Features
Figure 1 shows the TLP Pro 725T series front panel. The front panel of the TLP Pro 1025T series is very similar.
BB CC
EE
DD
AA
BB
Figure 1. TLP Pro 725T Front Panel
A LCD touchscreen
TLP Pro 725T series — 7-inch, 1024x600 resolution touchscreen
TLP Pro 1025T series — 10-inch, 1280x800 resolution touchscreen
The touchscreen is made with Corning Gorilla Glass, which is stronger and more scratch-resistant than standard glass, while
maintaining touch sensitivity, color saturation, and brightness.
B (2) — Detects motion between three to ve feet from the touchpanel, and at least 15° from the center axis.Motion sensor
zWhen no motion has been detected for a user-dened period of time, the touchpanel enters sleep mode.
zWhen motion is detected by the sensor, the screen display is restored and active.
C — Shows the conguration and connection status of the touchpanel:Communication LED
zUnlit during normal operation (the touchpanel is congured and connected to an IP Link Pro control processor).
zBlinks red if the touchpanel has been congured but is not connected to an IP Link Pro control processor.
zSolidly lit if the touchpanel has not been congured.
The indicator can be toggled between enabled and disabled, using the (see page 4). Setup Menu
D — Monitors ambient light level and adjusts screen brightness, based on the settings congured using the Light sensor
Setup Menu.
E — Can be programmed to provide system feedback:Status light
zLight red or green
zBlink or light continuously
For information about programming this light, see the or the .Global Configurator Help File Global Scripter Help File
2
TLP Pro 725T Series and TLP Pro 1025T Series • Setup Guide (Continued)
Rear Panel Features
AA
BB CC
Figure 2. TLP Pro 725T Rear Panel
A — Can be programmed to provide system feedback:Status light
• Light red or green Blink or light continuously•
For information about programming this light, see the or the .Global Configurator Help File Global Scripter Help File
B — Compatible with USB 2.0. The port is concealed behind a plastic cover, which can be removed with a small, USB-A port
at-bladed screw driver.
C — The LAN/PoE cable is inserted through this hole at the back of the base (see below).Cable guide LAN/PoE connector
Base
Figure 3 shows the base of the TLP Pro 725T series models. The base of the TLP Pro 1025T series models are very similar.
FFAA BB DD E
E G
GCC AA
Figure 3. TLP Pro 725T Base
A (2) — See on the previous page.Mounting hole Mounting
B — Activates the setup menu (see on Menu button Setup Menu
the following page).
C — Initiates one of three reset modes for the unit Reset button
(see on the following page).
Reset Modes: a Brief Summary
D — The LAN/PoE cable is inserted through this hole Cable guide
at the back of the base.
E — Indicates power status and reset status of the Reset LED
device (see on the following
Reset Modes: a Brief Summary
page).
F — Attach the LAN/PoE cable to this RJ-45 LAN/PoE Connector
port. The power injector must be purchased separately. Figure 4
shows the Extron XTP PI 100. Your power injector may look
different.
Connect a straight-through Ethernet cable from the power
injector to a switch or router (see gure 4, 1). This cable
carries network information from the switch or router to the
power supply input. A second straight-through cable carries the
network information and 48VDC from the power injector to the
touchpanel (2). Connect the IEC power cord to a convenient
100 VAC to 240 VAC, 50-60 Hz power source (3).
G — A single speaker provides audible feedback for the Speaker
user.
ATTENTION:
• Do not power on the touchpanels or control processors until you have read the ATTENTION in the “Base” section of
the .TLP Pro 725 and TLP Pro 1025 Series User Guide
• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section «Base » du
TLP Pro 725 and TLP Pro 1025 Series User Guide.
100-240V
~
50-60Hz
0.4A MAX
XTP
PWR
XTP PWR
To network switch To touchpanel
1
1 2
2
33
Figure 4. Connecting to a Power Injector
NOTE: Figure 2 shows the TLP Pro 725T series rear panel.
The TLP Pro 1025T series rear panels are very similar.
3
Product Category
Specyfikacje produktu
| Marka: | Extron |
| Kategoria: | monitor |
| Model: | TLP Pro 725T |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Extron TLP Pro 725T, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje monitor Extron
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
Instrukcje monitor
- monitor Sony
- monitor Yamaha
- monitor Samsung
- monitor PeakTech
- monitor UPERFECT
- monitor LG
- monitor Joy-It
- monitor Sharp
- monitor Huawei
- monitor Lenovo
- monitor Philips
- monitor Plantronics
- monitor SilverCrest
- monitor Gigabyte
- monitor Acer
- monitor Bosch
- monitor JBL
- monitor Hikvision
- monitor Fujitsu
- monitor LC-Power
- monitor Hisense
- monitor Panasonic
- monitor Promethean
- monitor Crestron
- monitor Viewsonic
- monitor Behringer
- monitor Asus
- monitor AG Neovo
- monitor IK Multimedia
- monitor Medion
- monitor Boss
- monitor Marquant
- monitor MSI
- monitor Toshiba
- monitor Westinghouse
- monitor Jensen
- monitor Yealink
- monitor Garmin
- monitor Blaupunkt
- monitor Iiyama
- monitor Citizen
- monitor APC
- monitor Haier
- monitor HP
- monitor Hyundai
- monitor Honeywell
- monitor Chauvet
- monitor Shure
- monitor Smart
- monitor Cooler Master
- monitor Alpine
- monitor Godox
- monitor Dynaudio
- monitor Deltaco
- monitor JVC
- monitor V7
- monitor Dell
- monitor Alesis
- monitor Vimar
- monitor Dahua Technology
- monitor Schneider
- monitor Eurolite
- monitor SMART Technologies
- monitor NZXT
- monitor Emos
- monitor Renkforce
- monitor Marshall
- monitor Viessmann
- monitor Omron
- monitor Thomson
- monitor Velleman
- monitor Neumann
- monitor DataVideo
- monitor Danfoss
- monitor Pyle
- monitor Newline
- monitor AOC
- monitor Peerless-AV
- monitor Speco Technologies
- monitor Samson
- monitor PreSonus
- monitor ARRI
- monitor Kindermann
- monitor Mitsubishi
- monitor Fluid
- monitor RCF
- monitor NEC
- monitor Brandson
- monitor Prestigio
- monitor OSEE
- monitor Sanyo
- monitor Elvid
- monitor Optoma
- monitor Focal
- monitor Asrock
- monitor Monkey Banana
- monitor Abus
- monitor AMCV
- monitor Jay-Tech
- monitor Mackie
- monitor Palmer
- monitor Barco
- monitor Insignia
- monitor AVer
- monitor Akuvox
- monitor 3M
- monitor Element
- monitor Denver
- monitor Marshall Electronics
- monitor Orion
- monitor Hitachi
- monitor Postium
- monitor Kali Audio
- monitor IStarUSA
- monitor Ernitec
- monitor Wohler
- monitor SmallHD
- monitor AJA
- monitor KRK
- monitor BenQ
- monitor Atlona
- monitor Simrad
- monitor Hanwha
- monitor Elo
- monitor Ikan
- monitor JUNG
- monitor Burg Wächter
- monitor Eizo
- monitor Monacor
- monitor Aputure
- monitor Tannoy
- monitor GVision
- monitor Positivo
- monitor SPL
- monitor Qian
- monitor Stairville
- monitor Vitek
- monitor Planar
- monitor Mobile Pixels
- monitor AMX
- monitor Alienware
- monitor Caliber
- monitor Sunstech
- monitor Sunny
- monitor Da-Lite
- monitor ProXtend
- monitor GeoVision
- monitor LaCie
- monitor InFocus
- monitor Swissonic
- monitor IHealth
- monitor Peaq
- monitor QSC
- monitor Hannspree
- monitor Avocor
- monitor Vivitek
- monitor Genelec
- monitor Interlogix
- monitor Vorago
- monitor EverFocus
- monitor POSline
- monitor Peerless
- monitor M-Audio
- monitor Mad Catz
- monitor Krom
- monitor Monoprice
- monitor Eve Audio
- monitor Yorkville
- monitor HoverCam
- monitor Voxicon
- monitor Sonifex
- monitor TV One
- monitor Fostex
- monitor Prowise
- monitor Soundstream
- monitor Xoro
- monitor HKC
- monitor CTOUCH
- monitor Ozone
- monitor Ibm
- monitor Maxell
- monitor Packard Bell
- monitor Provision ISR
- monitor Mybeo
- monitor CSL
- monitor Drawmer
- monitor Zalman
- monitor Iadea
- monitor Advantech
- monitor Hercules
- monitor Ganz
- monitor TVLogic
- monitor Gamber-Johnson
- monitor Legamaster
- monitor Belinea
- monitor Adam
- monitor Triton
- monitor Kogan
- monitor Posiflex
- monitor Antelope Audio
- monitor MicroTouch
- monitor EKO
- monitor ONYX
- monitor IBoardTouch
- monitor Mirai
- monitor Elite Screens
- monitor Mitsai
- monitor Christie
- monitor Skytronic
- monitor Enttec
- monitor Feelworld
- monitor COMMBOX
- monitor Yiynova
- monitor Alogic
- monitor Pelco
- monitor Lilliput
- monitor LightZone
- monitor AOpen
- monitor Planet Audio
- monitor EC Line
- monitor Datacolor
- monitor HELGI
- monitor Desview
- monitor Syscom
- monitor Allsee
- monitor Night Owl
- monitor ProDVX
- monitor Varad
- monitor DoubleSight
- monitor CTL
- monitor Game Factor
- monitor Nixeus
- monitor Chimei
- monitor Blue Sea
- monitor Faytech
- monitor Wyse - Dell
- monitor Approx
- monitor Bauhn
- monitor GeChic
- monitor Oecolux
- monitor ADS-TEC
- monitor Transvideo
- monitor Innocn
- monitor KeepOut
- monitor Shimbol
- monitor Raysgem
- monitor Ikegami
- monitor AORUS
- monitor Portkeys
- monitor Mimo Monitors
- monitor American Dynamics
- monitor AIS
- monitor Wortmann AG
- monitor Viotek
- monitor Vidi-Touch
- monitor KTC
- monitor CoolerMaster
- monitor Atlantis Land
- monitor HEDD
- monitor Colormetrics
- monitor IOIO
- monitor DTEN
- monitor Cocopar
- monitor Titan Army
Najnowsze instrukcje dla monitor
15 Października 2024
15 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
14 Października 2024
13 Października 2024
13 Października 2024
12 Października 2024