Instrukcja obsługi Extron IN1808

Extron Niesklasyfikowane IN1808

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Extron IN1808 (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/6

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

IN1808 Series • Setup Guide

The Extron IN1808 Series are eight-input seamless scaling presentation switchers that support signal resolutions up to

4K @ 60 Hz at 4:4:4. They feature DisplayPort, HDMI, and DTP2 inputs, HDMI output and a mirrored Extron DTP2 output

extension to send video, audio, and control signals up to 330 feet (100 meters) over a shielded CATx cable. The IN1808 IPCP SA

and IN1808 IPCP MA 70 models each have a built-in Extron IPCP Pro 355M IP Link Pro Control Processor, and an integrated

100 watt class D power amplier. The IN1808 Series delivers high image quality, fast and reliable switching, Extron ProDSP audio

processing, seamless video transition effects, logo keying, and HDMI loop out. The scalers can be controlled and congured over

Ethernet, RS-232, or USB.

This guide provides instructions for an experienced user to set up and congure the IN1808 (base model), IN1808 IPCP SA,

and IN1808 IPCP MA 70 scalers. It covers how to perform basic operations using the front panel controls and selected Simple

Instruction Set (SIS™) commands.

NOTES:

• For full installation, configuration, menus, connector wiring, and operation details, see the IN1806 and IN1808

Series User Guide at www.extron.com. For installation, configuration, and operation details of the embedded

IPCP Pro 355M, see the .IPCP Pro Series User Guide

• The IN1808 Series products can also be configured via the Extron Product Configuration Software (PCS), available at

www.extron.com. For information on using PCS, see the IN1806 and IN1808 Series Help File.

Installation

IN1808 Series Rear Panel Connectors

Figure 1 shows the rear panel of the IN1808 IPCP SA rear panel. The IN1808 IPCP MA 70 rear panel is the same except that

the embedded amplier is mono while the SA model amplier is stereo. The IN1808 base model rear panel does not have an

embedded IPCP Pro 355M module (see gure 1, P) or amplier module (N).

2x25W(8Ω)/2x50W(4Ω)

L R

CLASS 2 WIRING

AMPLIFIED OUTPUT

OUTPUTS (DTP/XT P/HDBT) AUDIO NPUTS OUTPUTS

HDMI/CEC

OVER TP

1A 1B

SIG LINK

OUT T x Rx

1 2

3 4

+48V

MIC/LINE

L R

AUX

3 4

INPUTS (DTP2/XTP)

LOOP OUT

4 6 7

S IG LINK

REMOTE

T x Rx

RS-232

RESET

100-240V~1.5A MAX

50-60 Hz

IN1808 IPCP SA

LAN

AV LAN 2 AV LAN 3

AV LAN 1

T x Rx

RT S CT S

T x Rx G T x Rx G

1 2 3 4 G

DIGI L I/OCOM 3COM 2COM 1 TA

S SG G

11 22 C 3 4 C +S G-S+V

PWR OUT = 6W

RRRRRRRRRRRRRRRRRRRRRRR

IR/SERIAL eBUSREL SAY

A C HB

E F G J KL

NQ P

Figure 1. Rear Panel Connectors, IN1808 IPCP SA

AC power connector

DisplayPort input connector (input 1)

HDMI (with CEC) loop out connector

DTP2/XTP input connectors (inputs 7

and 8)

HDMI (with CEC) output connector (1A)

DTP2/XTP/HDBaseT (with CEC) output

connector (1B)

Over TP IR pass-through connector

H Analog line audio inputs 3 and 4

I Analog mic/line audio inputs 1

and 2 and adjacent phantom

power LEDs

J Analog line audio outputs 1

through 4

K Remote RS-232 port

L Reset LED

M Reset button

N Amplified audio output (IPCP models

only)

o Aux mono or stereo analog line

audio input connector

P IPCP Pro 355M Control Processor

(IPCP models only)

Q HDMI inputs 2 through 6

R LAN connector (IN1808 base model

only, see the note and illustration

below)

NOTE: The IN1808 base model has a LAN connector to the left of the Remote RS-232 connector

(see R in the illustration at right) instead of the AV LAN ports on the IPCP Pro 355M control

processor.

Tx Rx

RS-232

RESET

1 2

3 4

LAN

OUTPUTS REMOTE

Tx Rx

RS-232

RESET

1 2

3 4

LAN

IN1808 • Setup Guide (Continued)

Mounting and Cabling

Step 1 Mount the device—

a. Turn off or disconnect all equipment power sources.

b. Mount the IN1808 to a rack using the pre-installed side mounting brackets, or remove the brackets and use an optional

19-inch rack under-desk mounting kit (see the mounting instructions provided with the kit, available at www.extron.com).

The IN1808 base model has a 1U high, full rack wide enclosure. The IN1808 IPCP models have 2U, full rack enclosures.

Step 2 Connect inputs—

Make the following input connections as needed:

• Connect a DP source to the Input 1 DisplayPort connector (see figure 1, B, on the previous page).

• Connect HDMI or DVI (with an appropriate adapter) sources to HDMI input connectors 2 through 6 (Q).

• Connect DTP transmitters to the DTP2/XTP RJ-45 input connectors 7 and 8 (

D). These connectors allow for remote

powering of DTP transmitters. You can configure the TP inputs for XTP mode via SIS commands, the on-screen

display (OSD), or PCS (see the ). For cable wiring and recommendations, see IN1808 Series Help File Twisted Pair

Recommendations for DTP, XTP, and HDBaseT Communication on the next page.

• Connect analog audio sources to:

• The 5-pole captive screw line audio input connectors 3 and 4 (H) and the Aux connector (O) for balanced or

unbalanced stereo audio. The Aux Line input is shared and can be associated with one or more video inputs.

• Connect balanced or unbalanced mic or line level inputs to 3-pole Mic/Line captive screw connectors 1 and 2 (I).

These inputs support optional +48 VDC phantom power, which is indicated by the LEDs at the left of the connectors.

Step 3 Connect outputs—

Make the following output connections as needed:

• Connect an HDMI, or DVI with an appropriate adapter, display to HDMI/CEC output connector 1A (E).

• Connect a DTP/XTP matrix switcher/HDBaseT compatible receiver to output connector 1B (F). For cable wiring and

recommendations, see Twisted Pair Recommendations for DTP, XTP, and HDBaseT Communication.

• To pass infrared data, connect a control device to the 3-pole IR Over DTP captive screw connector (see IR Over TP Wiring

on the next page). Alternatively, insert RS-232 communication to a DTP/HDBaseT endpoint via Ethernet (see the IN1808

Series User Guide for more information).

• Connect balanced or unbalanced analog audio output devices to one or both 5-pole captive screw output connector pairs

1 and 2 or 3 and 4 (J). See on the next page for more information. Audio Wiring

• For IPCP models, connect speakers to the amplifier module via the 5 mm 4-pole stereo (IN1808 IPCP SA) or 2-pole mono

(IN1808 IPCP MA 70) Amplified Output connector (N).

Step 4 Connect control devices—

• To control the base model through Ethernet, connect a LAN or WAN to the LAN connector (

R). To wire the RJ-45 connector

to the cable, see Twisted Pair Recommendations for DTP, XTP, and HDBaseT Communication.

For the IPCP models, connect a LAN or WAN to any of the AV LAN connectors on the IPCP Pro control processor (P). The

default IP address of the scaler is 192.168.254.254. The default subnet mask is 255.255.255.0. The default gateway address

is 0.0.0.0.

• For serial RS-232 control, connect a host device to the 3-pole captive screw connector (K). The default baud rate is 9600.

• For control through USB, connect a host device to the front panel USB mini-B port (see figure 2, H on page 4).

Step 5 Set up the IPCP Pro 355M control processor (IPCP models only)—

The Extron IPCP Pro 355M control processor (see , ﬁgure 1 P) provides monitoring and control of a variety of external devices,

such as projectors and lights. See the , available at IPCP Pro Series Setup Guide www.extron.com, for installation details.

Step 6 Connect power—

Connect a 100 to 240 VAC, 50-60 Hz power source to the AC power connector (A).

Twisted Pair Recommendations for DTP, XTP, and HDBaseT Communication

Extron recommends using the following practices to achieve full transmission distances

and reduce transmission errors:

• Use Extron XTP/DTP 24 SF/UTP cable for the best performance. At a minimum, Extron

recommends 24 AWG, solid conductor, STP cable with a minimum bandwidth of

400 MHz.

• Terminate cables with shielded connectors to the TIA/EIA-T568B standard (shown at

right).

• Limit the use of more than two pass-through points, which may include patch points,

punch down connectors, couplers, and power injectors. If these pass-through points

are required, use shielded couplers and punch down connectors.

ATTENTION:

• Do not connect these connectors to a telecommunications or computer data

network.

• Ne connectez pas ces ports à des données informatiques ou à un réseau de

télécommunications ou de données informatiques.

• DTP remote power is intended for indoor use only. No part of the network that

uses DTP remote power should be routed outdoors.

• L’alimentation DTP à distance est destiné à une utilisation en intérieur

seulement. Aucune partie du réseau qui utilise l’alimentation DTP à distance ne

peut être routée en extérieur.

NOTE: When using shielded twisted pair cable in bundles or conduits, consider the following:

• Do not exceed 40% fill capacity in conduits.

• Do not comb the cable for the first 20 meters, where cables are straightened, aligned, and secured in tight bundles.

• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.

• Separate twisted pair cables from AC power cables.

Audio Wiring

Wire the audio input and output connectors as shown at right. Use

the supplied tie wrap to strap the audio cable to the extended tail

of the connector. This does not apply to the amplied audio output

connector on the SA and MA models.

ATTENTION:

• For unbalanced outputs, do not connect wires to the

“-” poles (see the illustration at right).

• Pour les sorties asymétriques, ne connectez pas de

câbles aux pôles «-» (voir l’illustration de droite).

NOTE: The length of exposed wires is critical. The ideal length

is 3/16 inch (5 mm).

IR Over TP Wiring

To transmit and receive IR signals, connect a control device to the

three-pole Over TP IR connector (G, Tx, and Rx).

NOTE: RS-232 data can be inserted via Ethernet only (see the

IN1806 and for details).IN1808 Series User Guide

TIA/EIA-T568B

Pin Wire Color

1 White-orange

2 Orange

3 White-green

4 Blue

5 White-blue

6 Green

7 White-brown

8 Brown

1 2 3 4 5 6 7 8

RJ-45

Connector

Insert istedTw

Pair Wires

Pins:

Balanced Audio Output

Tip

Ring

Tip

Ring

Slee

ves

Unbalanced Audio Output

Tip

No Ground Here

Tip

Slee sve

L R

Unbalanced Audio InputBalanced Audio Input

Tip

Ring

Tip

Ring

Slee sve

Tip

Sleeve

Tip

L R

Do not tin the wires!

udio Inputs and Outputs 1 – 4 and xAu

Mic/Line Inputs 1 and

Balanced Audio Input

Tip

Slee

Ring

Unbalanced Audio Input

Tip

Sleeve

Specyfikacje produktu

Marka:	Extron
Kategoria:	Niesklasyfikowane
Model:	IN1808

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Extron IN1808, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Extron

Extron DTP T UWP 4K 232 D Instrukcja

9 Października 2024

Extron FOX Matrix 7200 Instrukcja

9 Października 2024

Extron EWB 210 Series Instrukcja

9 Października 2024

Extron EDID 101D Instrukcja

9 Października 2024

Extron FMR 206 Instrukcja

9 Października 2024

Extron EWB Series Instrukcja

9 Października 2024

Extron IR Sensor Instrukcja

9 Października 2024

Extron AVEdge 100 Instrukcja

9 Października 2024

Extron MLM 100 AAP Instrukcja

9 Października 2024

Extron MAAP 100 Instrukcja

9 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024