Instrukcja obsługi Extron DVS 304 DVI D

Extron Niesklasyfikowane DVS 304 DVI D

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Extron DVS 304 DVI D (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
The Extron DVS 304 Series of video and RGB digital scalers incorporate advanced technology
to provide high performance video processing with selectable output rates up to 1920x1200
(DVI models only) and HDTV 1080p, as well as simultaneous DVI (DVI models only) and
analog RGB or component video outputs.
This setup guide allows quick and easy set up and conguration of a DVS scaler using step by step instructions. It covers
performing basic operations using the front panel controls and selected Simple Instruction Set (SIS™) commands.
N For full installation, configuration, and operation details, refer to the DVS 304 Series User’s Manual, online at www.extron.com.
Installation — Rear Panel Features (DVS 304 DVI AD model shown)
INPUTS TOUTPU RS-232
LAN
RESET
ACT LINK
50/60 Hz
100-240V .3A
21 3 4L R L R
L RL RL R
AUDIO
VID
12 3
4
Y
/VID
R-Y H/
HV
R
/R-Y
V
G
/Y
B
/B-Y
DVI-I
YC
SDI B-Y
/C
RGB/R- B-Y/YC/VIDY, Y,
I
N
P
U
T
O
U
T
P
U
T
6
3a
3
7 4 5 91 2 11
8 10
DVS 304 I ADDV
Power and video input connections Output and control connections
a AC power connector Audio output connectors - (audio models only)g
b Audio input captive screw connectors (inputs 1 to 4) - audio models only RGB/YUV-HD BNC and DVI* output connectorsh
c i Composite video BNC connector (input 1) Reset button and LED
Ñ j (Optional) SDI BNC connectors (congurable) RJ-45 Ethernet connector
d k Composite video/S-video/component video BNC connectors (input 2) 9-pin D RS-232 connector
e S-video 4-pin mini-DIN connector (input 3)
f 15-pin HD connector (input 4) with EDID emulation*
Installation and cabling
Step 1 — Mount the DVS
Turn off or disconnect all equipment power sources and rack mount the DVS unit, using
suitable mounting brackets or rack shelf (see image at right).
Refer to the DVS 304 Series User’s Manual for details.
Step 2 — Connect inputs
Connect inputs from video and/or audio sources to the applicable connectors marked
“Inputs” (see above for connector types). See diagrams below for signal format on BNC b to f
connectors and audio input captive screw wiring (balanced or unbalanced, mono or stereo).
N When connecting a VGA input to a DV 304 DVI model, by default the EDID emulation is set to match the current output rate. To set to a specific rate,
or set to a display's EDID rate, or to upload a custom EDID table refer to the , available at DVS 304 Series User’s Manual www.extron.com.
Component video
(Y, R-Y, B-Y) S-video Composite video
B-Y
/C
Y
/VID
R-Y
B-Y
/C
Y
/VID
R-Y
B-Y
/C
Y
/VID
R-Y
Input 2
Input 4
Pin 1
15-HD pins Pin 2 Pin 3 Pin 13 Pin 14
Input source
BNC’s
R VHB
G
RGB
RGBcvS
YUV
S-video
Composite video
R G(S) B H V
RGBcvS
R-Y YB-Y
YC
Y
DVS 304 Series – Setup Guide
Rack Mount
Bra tcke
Unbalanced Stereo Input
Tip
Sleeve
Sleeve
Tip
L R
Unbalanced Mono Input
Balanced Mono Input
L R
Tip
Ring
Sleeve
Tip
Ring
L R
Tip
Sleeve
Tip
Sleeve
Balanced Stereo Input
L R
Tip
Ring
Sleeve
Tip
Ring
Do not tin the wires!
N * DVI models only. Non DVI models have a 15-pin HD connector
in place of the DVI connector and do not feature EDID emulation.
68-1039-50
Rev. A
08 09
DVS 304 Series • Setup Guide
2
DVS 304 Series — Setup Guide (cont'd)
Step 3 — Connect outputs
Connect video and audio output devices to the applicable connectors marked “Outputs” (see above). g and h
Video RGB (RGBHV, RGBS, RGsB) or HD component (R-Y, Y, B-Y) video output — For connect cables to the BNC's or VGA/DVI-I as shown
below. Outputs are scaled or pass-through RGB ,or scaled component video and can be scaled to more than 60 different output rates.
N RGB pass-through is available on analog outputs only. DVI output is disabled in RGB pass-through mode.
RGBHV
H/
HV
R
/R-Y
V
G
/Y
B
/B-Y
R
/R-Y
G
/Y
B
/B-Y
RGsB
H/
HV
V
R
/R-Y
V
G
/Y
RGBS
H/
HV
B
/B-Y
B
/B-Y
Component video (Y, R-Y, B-Y)
R
/R-Y
G
/Y
H/
HV
V
Analog video output
For connect a suitable display device DVI-I (digital and analog) output (DVS 304 DVI models only) ,
to this DVI-I connector for scaled RGB or component video (simultaneous digital and analog outputs).
Audio — Wire the captive screw audio connectors as shown above.
Step 4 — Connect control devices
LAN Ethernet port j — Connect to an Ethernet LAN or WAN via this RJ-45 connector to control the switcher from a remote
location using a PC’s Internet browser, or the control program (the Extron Signal Processing Products Control Program).
The Ethernet connection indicator LEDs indicate the status of the Ethernet connection: the green LED lights when connected to an
Ethernet LAN, and the amber LED ickers as the devices communicate.
N Do not use standard telephone cables, as they do not support Ethernet or Fast Ethernet. Do not stretch or bend cables as transmission
errors could occur.
Remote port —k For serial RS-232 control, connect a host computer or control system via this 9-pin D connector.
RS-232 protocol (default values): 9600 baud, 1 stop bit, no parity, 8 data bits, no ow control.
N See chapter 4, “SIS™ Programming and Control”, in the , for definitions of the SIS commands. DVS 304 Series User’s Manual
See chapter 5, “DVS 304 Series Control Software” to install and use the control software.
Use an RS-232 cable that only utilizes Tx (2), Rx (3), and ground (5) to avoid activating the contact closure feature (refer to the
DVS 304 Series User's Manual , chapter 2).
Step 5 — Connect power
AC power connector a — Plug in a standard IEC power cord from a 100 to 240 VAC, 50 - 60 Hz power source into this receptacle
Powering Up
When applying power to the DVS, the unit undergoes a start-up self testing sequence (see image below), and then the LCD displays
the default display cycle, showing the active input, input signal type, and the output resolution and refresh rate.
2
sec.
5
sec.
App ly
Power
Extron
El ec t roni cs
1
sec.
2 sec.
2
sec.
Default Display Cycle
INPU T 4
RGB SC ALED 1024x768@60.0Hz
OU T PUT
N
Th e i np ut an d o utp ut r ates sho wn
in the def ul t di spl ay cycle ma y d ifa fer,
de pe nd ing on the ac t i i np ut a nd type o f vide o s ign alve
.
All input LEDs flash
once in sequence
(last activ then 1-4).e,
1
sec.
2
sec.
Last active input
LED remains lit
(here input 3).
= flashing
Key
13
60-xxxx-xx
FW ve 2.00r.
= lit
DVS 304
DVI AD
2
sec.
N When in use and not in any menu, the LCD screen defaults to cycling through the current input/output configuration. The displayed
content may vary, depending on the input video signal type (see typical default display above).
DVI-I
A o outputudi
3
DVS 304 Series • Setup Guide
Front Panel Overview
1
DVS 304
VIDEO AND RGB SCALER
ADJUST
IR
2 3 4 MENU NEXT
3456 7
2
1
a Input selection buttons — Select/switch inputs and indicate which input is active (button LED lights green). A blinking LED
indicates an audio breakaway input (audio models only).
Button 1 selects input 1 - composite video.
Button 2 selects input 2 - composite video, S-video, or component video.
Button 3 selects input 3 - S-video.
Button 4 selects input 4 - RGB scaled (RGBHV, RGBS, RGsB), RGB pass-through, RGBcvS, YUVi, YUVp/HDTV, S-video or
composite video.
N RGB pass-through mode (inputs pass at their native rate without additional processing) is available on analog outputs only. The DVI
output is disabled in RGB pass-through mode.
b Menu button — This button allows navigation through the DVS's system menu (top level).
c Next button — This button allows navigation through the submenus and to start selected functions, such as Auto-Image™ .
d LCD display — This 12x2 screen displays device status, settings, and menu conguration information.
e Infrared (IR) sensor — This sensor is used to receive IR signals from the IR 902 remote control.
N For detailed information on the IR 902 remote, refer to the , available online at DVS 304 Series User's Manual www.extron.com.
f g and Adjust knobs — These are used with the menu navigation buttons to adjust device settings and picture control.
Setting the front panel lock (Executive mode)
The DVS has a front panel security lock feature that limits the operation of the unit from the front panel.
Executive mode 0 (disabled) — The front panel is fully unlocked. This is the default setting.
Executive mode 1 (enabled) — The front panel is locked except for input switching.
Enabling or disabling Executive mode 1 from the front panel
Press and hold the Menu and Next buttons until the LCD display indicates the Executive mode is either enabled or disabled.
N If the DVS is in Executive mode 0 (unlocked), this procedure selects mode 1 (locked).
If it is in Executive mode 1, this procedure selects mode 0 (unlocked).
When Executive mode is enabled and a front panel action is attempted (other than input switching), the LCD displays the status for
2 seconds. Executive mode 1 can also be enabled or disabled by SIS commands.
Configuring the DVS using the front panel system menus
The DVS has eight or nine front panel conguration menus:
Start Auto Image, Input Conguration, Picture Control, Output Conguration, Audio Conguration (only seen on audio models),
Memory Presets, IP Conguration, Advanced Conguration, and the Exit Menu.
N For detailed information on the menus, refer to the , available online at DVS 304 Series User's Manual www.extron.com.
To use a menu, press the Menu button to access the Main menu, then repeatedly press the Menu button to cycle through the list to
the desired menu. Press Next to enter the desired submenu, and follow the steps on page 4.
N Press Menu at any time to exit a submenu and return to the main menu.
Menu
Menu
Menu Menu
Menu Menu
START AUTO
IMAGE ON INx
INPUT
CONFIG
PICTURE
CONTROL
OUTPUT
CONFIG
AUDIO
CONFIG
MEMORY
PRESETS
IP
CONFIG
AD NCED VA
CONFIG
TO EXIT MENU
PRESS NEXT
(Audio models only)
2 sec.
2
sec.
Default Display Cycle
INPUT 4
RGB SSPA 1024 x768@6 0.0Hz
OUT PUT
Menu
Menu
Menu
Menu
Next

Specyfikacje produktu

Marka: Extron
Kategoria: Niesklasyfikowane
Model: DVS 304 DVI D

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Extron DVS 304 DVI D, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Extron

Extron

Extron DTP T UWP 4K 232 D Instrukcja

9 Października 2024
Extron

Extron FOX Matrix 7200 Instrukcja

9 Października 2024
Extron

Extron EWB 210 Series Instrukcja

9 Października 2024
Extron

Extron EDID 101D Instrukcja

9 Października 2024
Extron

Extron FMR 206 Instrukcja

9 Października 2024
Extron

Extron EWB Series Instrukcja

9 Października 2024
Extron

Extron IR Sensor Instrukcja

9 Października 2024
Extron

Extron AVEdge 100 Instrukcja

9 Października 2024
Extron

Extron MLM 100 AAP Instrukcja

9 Października 2024
Extron

Extron MAAP 100 Instrukcja

9 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024