Instrukcja obsługi Extech SDL500
Extech
Multimeter
SDL500
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Extech SDL500 (12 stron) w kategorii Multimeter. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/12
User Manual
Hygro-Thermometer / Datalogger
Model SDL500
Additional ManualUser Translationsavailable at www.extech.com
2 SDL500-en-GB_1.4 11/16
Introduction
Congratulations on your purchase of the Extech SDL500 Hygro-Thermometer, an SD Logger Series
meter. This meter displays and stores Temperature and Relative Humidity readings from the
supplied probe and Temperature readings from an optional Type J or K Thermocouple probe. WET
BULB and DEW POINT temperature calculations can also be displayed. Logged data readings are
stored on an SD card for transfer to a PC. This meter is shipped fully tested and calibrated and, with
proper use, will provide years of reliable service.
Meter Description
1. Optional Thermocouple Input jack
2. Supplied Relative Humidity / Temperature Probe input jack
3. LCD Display
4. Power ON-OFF key
5. HOLD and Backlight key
6. MAX-MIN key
7. Up arrow ▲ key
8. SET and Clock key
9. Down arrow ▼ / FUNCTION key
10. ENTER and LOG key
11. PC interface jack
12. Reset Button
13. Power Adaptor jack
14. SD card slot
15. Temperature and Humidity sensors
Notes: Items 11 – 13 are located behind the snap-off compartment cover on meter’s right side.
Battery compartment, tilt stand, and tripod mount are located on the rear of the instrument
3 SDL500-en-GB_1.4 11/16
Getting Started
Power ON-OFF
Power the meter by pressing and holding the power button for at least 1.5 seconds.
Press and hold the power button for at least 1.5 seconds to power OFF the meter.
This meter is powered by six (6) 1.5VDC ‘AA’ batteries or by optional AC adaptor. If the meter
will not switch ON please check that fresh batteries are installed in the rear battery compartment
or, in the case of the AC adaptor, check that the adaptor is connected correctly to the meter and
to an AC source.
Connecting the Supplied Relative Humidity/Temperature Probe
The supplied RH/Temperature Probe uses a keyed DIN-style plug to connect to the meter.
Connect the supplied probe to the top right of the meter in the DIN jack labeled ‘Probe Input’.
Press and hold the FUNCTION button until the ‘RH’ display icon appears. Release the button
when this ‘RH’ display icon appears. The RH reading in % are now on the upper, larger LCD
digits and Temperature in degrees ‘C’ or ‘F’ are now on the lower, smaller LCD digits.
Use the Setup Mode to further configure the meter.
Connecting an optional Thermocouple Sensor
The SDL500 accepts an optional Type ‘J’ or Type ‘K’ Thermocouple Temperature sensor.
1. Connect a thermocouple to the sub-miniature jack at the top left of the meter labeled
‘Thermocouple Temp. Probe’.
2. Press and hold the FUNCTION button until the ‘TP’ display icon appears. Release the button
when this ‘TP’ display icon appears. The thermocouple reading in degrees ‘C’ or ‘F’ is now on
the LCD. The thermocouple type (‘J’ or K’) and the unit of measure are also displayed.
3. Use the Setup Mode to further configure the meter.
IMPORTANT SAFETY NOTE: The SDL500 can measure and display temperature up to 1300
o
C
(2372
o
F), however, thermocouple ratings vary widely; ensure that the thermocouple being used
is rated accordingly for the temperature being measured.
If an attempt is made to measure temperatures higher than the thermocouple’s rating, damage
to the thermocouple and the meter can result. If measurements are made outside the range of a
thermocouple personal injury is also possible.
Specyfikacje produktu
Marka: | Extech |
Kategoria: | Multimeter |
Model: | SDL500 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Extech SDL500, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Multimeter Extech
14 Września 2024
30 Sierpnia 2024
26 Sierpnia 2024
25 Sierpnia 2024
24 Sierpnia 2024
18 Sierpnia 2024
16 Sierpnia 2024
14 Sierpnia 2024
13 Sierpnia 2024
6 Sierpnia 2024
Instrukcje Multimeter
- Multimeter PeakTech
- Multimeter Voltcraft
- Multimeter Milwaukee
- Multimeter GW Instek
- Multimeter Stanley
- Multimeter TFA
- Multimeter Chauvin Arnoux
- Multimeter Gembird
- Multimeter Uni-T
- Multimeter Owon
- Multimeter Emos
- Multimeter Velleman
- Multimeter Gossen Metrawatt
- Multimeter Fluke
- Multimeter BENNING
- Multimeter Metrix
- Multimeter Ferm
- Multimeter Testboy
- Multimeter Kyoritsu
- Multimeter Powerfix
- Multimeter Monacor
- Multimeter Laserliner
- Multimeter Profile
- Multimeter Appa
- Multimeter Amprobe
- Multimeter Tacklife
- Multimeter Somogyi
- Multimeter Steren
- Multimeter Flir
- Multimeter Maxwell
- Multimeter Topcraft
- Multimeter Altai
- Multimeter Plieger
- Multimeter Greenlee
- Multimeter Högert
- Multimeter Wago
- Multimeter Bruder Mannesmann
- Multimeter Metrel
- Multimeter Digi-tool
- Multimeter Elma
- Multimeter PCE Instruments
- Multimeter CEM
Najnowsze instrukcje dla Multimeter
19 Września 2024
18 Września 2024
18 Września 2024
17 Września 2024
17 Września 2024
17 Września 2024
17 Września 2024
17 Września 2024
17 Września 2024
16 Września 2024