Instrukcja obsługi Eureka Timberline

Eureka namiot Timberline

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Eureka Timberline (2 stron) w kategorii namiot. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

ASSEMBLY INSTRUCTIONS FOR THE

TIMBERLINE and TIMBERLINE OUTFITTER TENTS:

Component List:

1 Tent Body, 1 Tent Bag 4 Poles 1 Spanner

1 Tent Fly, 2 Fly Rods 1 Pole Bag

2 Junction Tubes 1 Stake Bag and Stakes

• Unroll and unfold the tent and lay it on the ground. Remove

the ﬂy and open the tent door. Do not stake down the tent just yet;

But in windy conditions, stake down one front corner into wind.

NOTE: Do not drop tent bag or pole bag on its end. Do not bounce tent

bag on its end to get tent out. These actions may cut the shock cord and/or

damage the pole ends.

• Assemble all the shock-corded poles. Make sure each pole section has ﬁrmly

seated into the adjacent section. Try to keep the poles from snapping together

as this can damage the rod ends. Through usage, the aluminum frame may

bend slightly and take a "set" this normally does not affect performance.

•

Place the tapered end of a pole onto the diagonal hole in the junction tube.

The junction tube is marked UP RT- [TOP RIGHT on TL6]- so the pole will

seat at the correct angle.

Insert a corner pin into the other end of the pole.

See fig.1.

• Repeat with the second pole and at the back of the tent with the last two

poles and the remaining junction tube.

• Disconnect the rods in the middle of the spanner. Place one end of

the spanner through the center hole of the ﬁrst junction tube. Place

the opposite end of the spanner

through the center hole in

second tube.

See fig.2.

• Push down on the disconnected

rods until they join together. This forms

the free standing frame. See fig.3.

• Connect the tent to frame by pulling the shock-corded loops, at the

peaks of the tent, over the junction tubes. Snap tent clips to the poles.

NOTE: Junction tubes can be tied to the tent with the strings provided.

Tie one end to the shock-cord loop. Pass the other end through the

1/8" hole in the junction tube and tie a knot.

See fig.4.

• Orient the tent in the desired location and stake it down.

• Fit each of the ﬂy rods over the tip of the spanner section protruding

through each junction tube.

• Drape the ﬂy over tent so the center S-hooks [ sewn on the underside

of the fly ] line up with the rods.

• Insert the center S-hook into one end of the fly rod. Pull the opposite

S-hook and insert it into the end of the second fly rod.

TIMBERLINE SERIES TENTS ARE EQUIPPED WITH

HIGH / LOW VENTING DOORS:

• To allow cool air into the tent, unzip the low vent on the door

and hold open with the hook and loop tab.

• To vent the fly, unzip the two zippers at the base of the vestibule.

• To allow warm, moist air to escape, unzip the peak of the door

and roll down and/or the peak of the back window.

OPTIONAL EQUIPMENT:

Annex: Front awning for storing gear and cooking.

Gear Loft: Mesh hammock attaches to rings inside the tent

for drying clothes or storing accessories.

Floor Saver: Place under tent to protect the ﬂoor and keep

it clean. Also provides an additional moisture barrier.

fig.1

fig.2

fig.3

fig.4

IMPORTANT:

Do not attempt this assembly with the spanner joined.

• Connect the snaps on the underside of the fly to the rings on side of

the tent. See fig.5.

• Connect four shock-corded S-hooks, located at ﬂy corners, to the

ring and pin assemblies at base of each pole.

• Stake down the two pull outs on the sides of the Fly.

See fig.6.

TL6 only

RECOMMENDATIONS:

• During strong winds, tie extra ropes [ not included ] to the

storm rings on the ﬂy and stake down securely. Note staking pattern.

See fig.6.

• Take-down task sequence:

Remove ﬂy and open door.

Disconnect hooks and peak shock-cords.

Remove clips from the tent poles; then pull the pins

out from the pole ends.

REV E 4.09

fig.6.

fig.5.

Pull out

Stake

Storm Ring

Stake

Good:

4 stakes /4 lines Best:

4 stakes /8 lines

REV E. FEB 09

SEAM SEALING:

We recommend use of a sealer such as Kenyon Seam Sealer 3 or McNett Outdoor

SeamGrip

• Work in a fully ventilated area.

• Set the tent up or lay the tent out ﬂat. Taut seams allow for even application and

penetration of the sealer.

• Decide which seams need to be sealed. For example, seams that will be exposed

to rain, runoff, or ground level water are a must for sealing, while seams on

uncoated nylon or mesh panels don’t need treatment. There is no need to seal

the seams in the roof or the factory taped seams. We recommend sealing both

ﬂoor and ﬂy seams and reinforcements.

• Apply sealant to the inside and outside of all exposed seams. Several thin layers

will work better than one thick layer. Read and follow manufacture's instructions.

STAKING:

All tents need to be staked down to keep them from blowing away. Securing the

tent by placing heavy objects inside is just not adequate.

• Once the tent body is erected, stake it out before the ﬂy is put on. This enables you

to square the tent up to ensure that the ﬂy goes on properly and that the seams

align with the frame. Pull the base of the tent taut between each web stake out

loop or ring & pin. Make sure that all corners are square. It is important that you

don’t stake the tent out too tightly. You will know it’s too tight, if the door zippers

can not be easily operated. Drive stakes through the web loops, or with ring & pin,

drive the stake just outside the ring so that the “J” hook catches it. Tie a piece of

cord or web into a loop through the ring to be used as a large stake loop if

needed.

• With the tent properly staked, drape the ﬂy over the frame, attach its tent

connection points and stake down any pull outs.

• Do not attempt to remove the stakes by pulling on the tent becket loop, as this

could cause the fabric to tear. The best way is to pry on the stake itself.

Staking in special conditions:

• Sand. Use long, broad stakes with plenty of surface area in loose soil.

• Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes

separately. Their sharp edges can cut fabric and leave rust stains, which might

damage your tent.

• Snow. Use “dead man” anchors. Tie tent to buried objects (branches, tent bags, or

stuff sacks ﬁlled with snow; or tie tents to snow shoes, skis, or ski poles, which are

stuck in the snow.

GUY LINES:

Do not depend upon staking alone to keep your tent secure during high winds. Most

tent models have built-in loops or rings at optimal guy out locations. It’s important

to put in the extra time guying out your tent. Correctly done, it can save your tent

during exceptional weather.

• Make sure that the top ﬂy is securely attached to the tent frame. Ties, hook and

loop, or dog-bones and elastic loops are sewn to the underside of the ﬂy for this

purpose.

• Attach parachute cord to the loops/rings and stake them in the ground three or

four feet from the edge of the tent. If staked too close to the tent, wind can cause

an upward pull that could dislodge the stakes.

• If your tent does not have loops or rings for guy outs, attach guy lines 1/3 to

1/2 of the way up the framework on the main sidewalls. This enables the

guy line to support the lower section of the pole, while the upper pole can

ﬂex and deﬂect wind gusts. It is best to run two cords at an angle from the

side of the guy out. This prevents all movement, except toward the anchor.

The guy lines will work together through opposition. See illustrations below:

CONDENSATION & VENTING:

Through perspiration and breathing, an adult gives off about a pint of water

overnight. If it cannot escape, the water vapor condenses to liquid. Most

often, water found in the tent is a result of this condensation rather than

from the tent leaking. Condensation often forms where the sleeping bag

touches the side of the tent, under the sleeping pad, or on coated surfaces

such as the door ﬂaps. A tent’s double wall construction allows the vapor to

escape through the roof to the outside, keeping the inside of the tent dry.

Leave the windows partially open at night to provide cross ventilation and

further reduce condensation. Cross ventilation becomes more important in

very humid or extremely cold conditions when the permeable roof is less

effective. The features that enhance ventilation are windows, short-sheeted

ﬂys (bottom venting), roof vents, and High/Low venting doors. These are

speciﬁc to each tent model.

Given the importance of proper ventilation, We use High/Low venting in most

of our tents. This allows cooler air in through the low vents and warmer,

moist air up and out through the high vents. High/Low venting is

accomplished within the inner tent via roof vents, doors and windows. It is

important to vent the vestibule. Unvented, it can inhibit airﬂow into the tent.

Our tent vestibules proﬁt from the ability to “short sheet” by means of

zippers & toggles and staked vestibule pull outs create a bellowing effect.

Most of our tents are equipped with a High/Low venting door. This design

allows increased airﬂow into the tent from the bottom. Open the low

vent/window to admit cool air, allowing the warmer air out through the

high roof vents. When rain and wind prevent the low vent from being

opened, the high door vent can still be used. Fly overhangs or vestibules

protect it.

ULTRAVIOLET LIGHT:

Ultraviolet light damage to tent fabric is caused by excessive exposure to

sunlight. While our fabrics are UV resistant, any synthetic fabric is

susceptible to UV degradation. UV damage will cause nylon and polyester

to become brittle and tear easily. We recommend that you use the rain ﬂy

even on clear days. It acts as a sunscreen to the tent. A rain ﬂy is both easier

and less expensive to replace if damaged. UV damage can be minimized by

erecting tents on shaded sites with low exposure to direct sunlight.

GENERAL POLE CARE:

• Never let tent poles snap together as this can damage the pole end.

• Do not drop tent or pole bags on their ends and do not bounce a tent bag

on its end to get the tent out. These actions may cut the shock cord and

damage the pole ends.

• The aluminum frame may bend slightly and take a “set” through usage; this

normally does not affect the performance of the frame.

GENERAL TENT CARE:

• Sweep the tent ﬂoor daily to prevent damage from stones.

• Try not to wear shoes inside your tent.

• Use a ground cloth whenever possible.

• Do not keep food inside a tent. Hungry critters will chew through tent fabric in

search of food.

STORAGE:

• Make sure the tent is completely dry, then store loosely rolled, in a dry, cool

place. To prevent dust from collecting on the tent, cover it with a cloth. This

allows the nylon/polyester fabric to breathe.

• Ideally, the tent poles should be stored in their fully assembled state. This

reduces the tension on the shock cord, prolonging its life.

• The tent bag should be used only as a carry sack and not for storage.

COLOR TRANSFER:

• Do to the nature of tent fabrics, color can transfer from darker to lighter

fabrics when the two fabrics are in contact over time when wet, damp or

exposed to the combination of moisture and high heat. This does not effect

the tent's performance. To prevent / minimize color transfer, always make

sure your tent is completely dry prior to packing and storage.

CLEANING:

• Clean the tent by setting it up and wiping it down with a mild soap (liquid

hand soap) and lukewarm water solution. Rinse thoroughly and dry

completely. Never use detergent, washing machines or dryers because they

can damage the tent’s protective coating and seams. After cleaning, be sure

the tent is completely dry, especially the heavier, double-stitched areas such

as the seams, before storing or mold / mildew are likely to grow.

• Clean the tent poles with a cloth and lubricate them with silicone spray. This is

especially necessary after ocean side camping to remove salt spray so the

poles don’t corrode or stay gritty.

• Clean the zippers with a quick dip in water and then dry them off. This is

especially important if you’ve been camping in a location with sand/dirt. If

you don’t clean the zippers, the sliders will wear out and eventually the teeth

will become inoperable.

ALTERATIONS OR MODIFICATIONS:

DO NOT misuse, modify or alter this product in any way from its condition at

the time of sale. Alteration, modification or any use of this product contrary

to the accompanying written instructions shall void the warranty. Moreover,

any misuse, alteration or modification of the product shall absolve Johnson

Outdoors Gear LLC of any liability for property damages or injuries sustained

as a result of such misuse, modification or alteration.

LIMITED WARRANTY:

What Is Covered: Johnson Outdoors Gear LLC

warrants to the original

purchaser that its products are free from defects in material and workmanship,

for the life of the product, except as qualiﬁed below. The life of the product is

determined from the date of purchase until such time as the product is no longer

serviceable due to normal wear and tear.

What Is Not Covered:

Johnson Outdoors Gear LLC

shall not be responsible for the

natural breakdown of materials that occurs inevitably with extended use (e.g., Ultra

Violet (UV) light damage on tents, exhausted zippers), or defects caused by accident,

abuse, alteration, animal attack, storm damage, misuse or improper care.

THERE ARE NO OTHER EXPRESS WARRANTIES BEYOND THE TERMS OF THIS

LIMITED WARRANTY. IN NO EVENT SHALL JOHNSON OUTDOORS GEAR LLC BE

LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

What Johnson Outdoors Gear LLC Will Do: If after inspection we ﬁnd that a

product failed due to a manufacturing or material defect, we will repair or

replace the product, at our option, without charge.

How to Obtain Warranty Service: Return the product, freight prepaid, to the

Dealer from whom it was purchased; or, contact our Customer Satisfaction

Department for return authorization: toll free 1-800-572-8822. Collect

shipments or shipments without return authorization cannot be accepted. The

product registration card packaged with our product need not be returned for

the warranty to be effective and for you to receive warranty service.

Repairs: If your

Johnson Outdoors Gear LLC

product needs service or repair

due to normal wear and tear, animal attack, accident or some other reason

that is not covered under the warranty we will provide the necessary service

for a reasonable charge, plus shipping and handling. We require that products

accepted for any repair be properly cleaned according to our recommended

care instructions. Please send your product or component that requires repair

(e.g., tent ﬂy), postage prepaid, along with a description of what needs

attention. For service and repairs, please contact our Customer Satisfaction

Department: toll free 1-800-572-8822

How State Law Relates To This Warranty: This warranty gives you speciﬁc

legal rights, and you may have other rights that vary from state to state.

Our experience building quality

outdoor equipment goes back over 100

years! Today, we manufacture sleeping

bags, screen houses, day-use

shelters and . We also camping tents

design and manufacture tents for the

United States Military and for the

rental industry.

See eurekatents.com

From baseplate and digital

compasses to electronic

instruments, our sister brands, Silva

and Tech4o, put outdoor technology at

your fingertips.

See and tech4o.com silvausa.com

Our brands are part of the Johnson

Outdoors family of products. Visit all

the brands at johnsonoutdoors.com

We support the "Leave No Trace"

Seven Principles:

1. PLAN AHEAD AND PREPARE

2. TRAVEL & CAMP ON DURABLE SURFACES

3. DISPOSE OF WASTE PROPERLY

4. LEAVE WHAT YOU FIND

5. MINIMIZE CAMPFIRE IMPACTS

6. RESPECT WILDLIFE

7 . BE COURTEOUS OF OTHER VISITORS

JOHNSON OUTDOORS GEAR LLC

WARNING:

KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC.

• This tent meets the ﬂammability requirements of CPAI-84. The fabric may

burn if left in continuous contact with any ﬂame source. The application of

any foreign substance to the tent fabric may render the ﬂame-resistant

properties ineffective.

• Do NOT operate any device which burns fuel inside your tent. Combustion

consumes oxygen and can produce dangerous levels of carbon monoxide,

which could lead to serious injury or death.

Specyfikacje produktu

Marka:	Eureka
Kategoria:	namiot
Model:	Timberline
Kolor produktu:	Black,Blue
Źródło zasilania:	Bateria
Waga produktu:	6100 g
Czas ładowania:	79 min
Poziom ciśnienia akustycznego:	90 dB
Pojemność baterii:	8 Ah
Silnik:	Bezszczotkowy
Konstrukcja produktu:	Wiertarka pistoletowa
Regulowana prędkość:	Tak
Napięcie baterii:	18 V
Średnica wiertła w betonie (max):	35 mm
Walizka:	Tak
Rodzaj zacisku:	SDS Max
Średnica wiertła w metalu (max):	- mm
Średnica wiertła w drewnie (max):	- mm
Ładowarka akumulatorów:	Tak
Prędkość biegu jałowego (max):	500 RPM
Poziom mocy dźwięku:	101 dB
Wbudowane światło:	Tak
Wiercenie:	Tak
Wiercenie udarowe:	Tak
Maksymalna szerokość szczęk:	- mm
Dołączony akumulator:	Tak
Liczba baterii włączone:	2 szt.
Niepewność poziomu dźwięku:	3 dB
Dodatkowa rękojeść:	Tak
Liczba udarów (wysoka prędkość):	2900 bpm