Instrukcja obsługi Ergotron ZDE02CG/CG


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ergotron ZDE02CG/CG (4 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/4
1 of 4
300-5522-00 rev. B • 06/16
Zido® 2-drawer Enclosure
Built with Anthro-DNA
NOTE: The Zido cart is not included.
Product Part#
Zido 2-drawer Enclosure ZDE02SB/CG
For the latest User Installation Guide please visit: www.ergotron.com
User's Guide
2 of 4
300-5522-00 rev. B • 06/16
01
02
03
04
05
06
07
Product Quantity Part Number
01 Drawer Body 1 835-539X-00
02 Upper Drawer Body 1 835-5236-00
03 Lower Drawer Body 1 835-5397-00
04 Enclosure Brackets 2 225-2732-00
05 Self-threading Screws 8 325-5464-00
06 Nylock Nuts 8 325-5259-00
07 Lock Assembly 1 325-5074-00
TH I S I S A 2-P E R S ON
J O B !
Grab a buddy!
TOOL S
A 7/16" nutdriver or socket is use-
ful for this assembly.
PA R TS L I S T
Before beginning assembly of your drawer enclosure,
please review the parts list to verify that your shipment is
complete.
3 of 4
300-5522-00 rev. B • 06/16
Self-threading Screw
325-5464-00
1/4-20 Nylock Nuts
325-5259-00
Drawer Tabs
Lock
Nut
Cam
Screw
S T E P 1
Remove the Drawers; Install the Lock
Pull the drawer all the way out. Locate the drawer tabs on the glides
on each side of the drawer body. Depress the drawer tabs (one goes
up and one goes down) to release the drawer from the glides. Slide the
drawer o the glides and set aside.
Repeat for the lower drawer.
Install the lock into the lower drawer. Insert the lock cylinder inside the
lock body, then slide that assembly through the hole at the front of the
drawer body. Attach the lock assembly to the lower drawer using the
Nut. Make sure that the key is horizontal in the lock when the assembly
is attached to the drawer. Locate the straight Cam in the kit. Slip the
camp over the end of the lock and secure all the pieces with the screw
using a Phlilips screwdriver. Make sure that the Cam is facing up when
the key is horizontal.
S T E P 2
Install the Brackets onto the Column
Select an installation point for the drawer body. When installed, the
top of the drawer body will be about 1/2" above the top of the upper
bracket.
Install the top bracket using four 3/4" self-threading screws. Install the
lower bracket with one hole open below the upper bracket.
Carefully tip the cart on its back so that the pins on the brackets are
facing up.
S T E P 3
Install the Enclosure
Lift the enclosure body onto the cart so that the pins on the brackets
line up with the holes on the enclosure body.
Attach the body to the brackets using a 7/16" nutdriver or socket or the
3-way wrench and eight Nylock Nuts.
S T E P 4
Install the Drawers
Slide the larger drawer into place. Move it in and out a few times to set the ball bearings in the glides.
Slide the small drawer into place. Move it in and out a few times to set the bearings.
CO N G R ATU L AT I O N S ! YO U R D R AW E R E N C LO S U R E A S S E M B LY I S CO M P L E T E !


Specyfikacje produktu

Marka: Ergotron
Kategoria: Nie skategoryzowane
Model: ZDE02CG/CG

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Ergotron ZDE02CG/CG, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Nie skategoryzowane Ergotron

Instrukcje Nie skategoryzowane

Najnowsze instrukcje dla Nie skategoryzowane

IFM

IFM PE2599 Instrukcja

3 Kwietnia 2025
IFM

IFM RU6035 Instrukcja

3 Kwietnia 2025
Bestway

Bestway 9102S Instrukcja

3 Kwietnia 2025
Bestway

Bestway 9102T Instrukcja

3 Kwietnia 2025
Bestway

Bestway 21177 Instrukcja

3 Kwietnia 2025
Bestway

Bestway 21178 Instrukcja

3 Kwietnia 2025
Ruggard

Ruggard GTUV-SG Instrukcja

3 Kwietnia 2025