Instrukcja obsługi Epson powerlite 1710c multimedia projector
Epson
Projektor Beamer
powerlite 1710c multimedia projector
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Epson powerlite 1710c multimedia projector (102 stron) w kategorii Projektor Beamer. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/102
PowerLite® 1700c/1710c
Multimedia Projector
User’s Guide
2
Important Safety Information
WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes.
Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and
filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically
explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service
personnel.
WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small
children to avoid any risk of suffocation.
Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by
the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation. The information contained herein is designed only for use with
this Epson product. Epson is not responsible for any use of this information as applied to other products.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for
damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of
this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to
strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or
any consumable products other than those designated as Original Epson Products or Epson Approved Products by
Seiko Epson Corporation.
Trademarks
Epson and Instant Off are registered trademarks, and Epson Exceed Your Vision and EasyMP are trademarks of
Seiko Epson Corporation.
PowerLite and PrivateLine are registered trademarks; SizeWise is a trademark; and Epson Connection, Epson
Store, and Epson Extra Care are service marks of Epson America, Inc.
Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.
© 2007 Epson America, Inc. 9/07
CPD-21955R1
3
-
Contents
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Getting More Information . . . . . . . . . . . . . . . . . . . . . . . . 8
Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Additional Components. . . . . . . . . . . . . . . . . . . . . . . . . 10
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1Displaying and Adjusting the Image . . . . . . . . 13
Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Projecting the Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Turning On the Projector . . . . . . . . . . . . . . . . . . . . . . . 15
Selecting the Image Source. . . . . . . . . . . . . . . . . . . . . . . 17
Troubleshooting Display Problems. . . . . . . . . . . . . . . . . . . . 18
You Can’t Project an Image . . . . . . . . . . . . . . . . . . . . . . 18
The Projector and Notebook Don’t Display the
Same Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Adjusting the Height of Your Image . . . . . . . . . . . . . . . 20
Focusing and Zooming Your Image . . . . . . . . . . . . . . . . 21
Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 21
Correcting Computer Images. . . . . . . . . . . . . . . . . . . . . 23
Using the A/V Mute Slide . . . . . . . . . . . . . . . . . . . . . . . 23
Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . . . . 23
Using the Direct Power On Function . . . . . . . . . . . . . . 24
4
2Using the Remote Control . . . . . . . . . . . . . . . . . . . 25
Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Replacing the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . 26
Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 27
Switching Between Picture Sources . . . . . . . . . . . . . . . . 27
Turning Off the Picture and Sound . . . . . . . . . . . . . . . . 28
Stopping Action. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Zooming Part of Your Image . . . . . . . . . . . . . . . . . . . . . 29
Controlling the Volume. . . . . . . . . . . . . . . . . . . . . . . . . 29
Resizing Video Images . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Adjusting the Color Mode . . . . . . . . . . . . . . . . . . . . . . . 30
Operating Your Computer with the Remote Control. . . . . . 31
Highlighting Your Presentation . . . . . . . . . . . . . . . . . . . . . . 32
Using the Pointer Tool . . . . . . . . . . . . . . . . . . . . . . . . . 32
Customizing the Pointer Tool . . . . . . . . . . . . . . . . . . . . 32
3Connecting to Computers and
Other Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . 34
Connecting to the Computer Port . . . . . . . . . . . . . . . . . 34
Connecting the Cable for Remote Mouse Control . . . . 35
Connecting to Video Equipment . . . . . . . . . . . . . . . . . . . . . 36
Connecting a Composite Video Source . . . . . . . . . . . . . 37
Connecting an S-Video Source . . . . . . . . . . . . . . . . . . . 38
Connecting a Component Video Source . . . . . . . . . . . . 39
Connecting an RGB Video Source. . . . . . . . . . . . . . . . . 40
Playing Sound Through the Projector . . . . . . . . . . . . . . . . . 40
4Fine-Tuning the Projector. . . . . . . . . . . . . . . . . . . 43
Using the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . 45
Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Six-Axis Color Adjustment. . . . . . . . . . . . . . . . . . . . . . . 47
Adjusting Signal Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . . 50
5
Using the Projector Security Features . . . . . . . . . . . . . . . . . . 51
Enabling Password Protection . . . . . . . . . . . . . . . . . . . . 51
Creating Your Own Startup Screen . . . . . . . . . . . . . . . . 54
Disabling the Projector’s Buttons. . . . . . . . . . . . . . . . . . 56
Customizing Power and Operation. . . . . . . . . . . . . . . . . . . . 57
5Maintaining the Projector. . . . . . . . . . . . . . . . . . . 59
Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . 60
Cleaning the Air Filter and Vent. . . . . . . . . . . . . . . . . . . . . . 61
Replacing the Lamp and Air Filter . . . . . . . . . . . . . . . . . . . . 62
Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . . 65
Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 66
6Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Using On-Screen Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Checking Projector Status. . . . . . . . . . . . . . . . . . . . . . . . . . . 69
What To Do When the Lights Flash . . . . . . . . . . . . . . . 69
Viewing Lamp Usage and Other Information . . . . . . . . 71
Solving Projector Operation Problems . . . . . . . . . . . . . . . . . 71
Solving Problems with the Image or Sound . . . . . . . . . . . . . 72
Solving Problems with the Remote Control . . . . . . . . . . . . . 77
Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Speak to a Support Representative . . . . . . . . . . . . . . . . . 78
AProjector Installation . . . . . . . . . . . . . . . . . . . . . . . . 81
BTechnical Specifications . . . . . . . . . . . . . . . . . . . . . 83
6
CNotices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . 89
Remote Control Information . . . . . . . . . . . . . . . . . . . . . . . . 91
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . 92
FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . . 93
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
7
-
Welcome
The PowerLite® 1700c/1710c is an easy-to-use projector that weighs
less than 4 pounds. The projector offers up to 2700 lumens (1710c) or
2200 lumens (1700c) of brightness. You can connect it to a wide
range of computers and video sources.
Easy setup, control, and security:
■5-second startup time and Instant Off ® feature for fast setup and
shut down
■Automatic digital keystone correction
■1.2x optical zoom lens for flexible placement and positioning
■Security features include password, user’s logo, and the ability to
lock the projector buttons
■A/V mute slide to block the lens and save lamp life when you
want to temporarily stop projecting
8Welcome
Using Your Documentation
This book contains all the information you need to set up and use
your projector. Please follow these guidelines as you read through it:
■Warnings must be followed carefully to avoid bodily injury.
■Cautions must be observed to avoid damage to your equipment.
■Notes contain important information about your projector.
■Tips contain additional projection hints.
Getting More Information
Need tips on giving presentations? Quick steps for setting up your
projector? Here’s where you can look for help:
■Quick Setup sheet
Gives you the instructions you need to get your projector up and
running if you are connecting to a notebook, MacBook,TM
PowerBook,
®
or iBook® computer.
■Projector kit
Includes this User’s Guide, your Quick Setup sheet, warranty
brochures, and Epson PrivateLine® Support card. Keep the kit
with your projector at all times.
■Built-in help system
Provides assistance for common problems. Available from the
Help button on the projector or the remote control. See page 68
for details.
■epson.com/support
Download FAQs and e-mail your questions to Epson support.
■If you still need help after checking this User’s Guide and the
sources listed above, you can use the Epson PrivateLine Support
service to get help fast. Call (800) 637-7661 and enter the PIN on
the PrivateLine card. Or take advantage of Epson’s automated
support services 24 hours a day. See page 78 for more
information.
Welcome 9
■presentersonline.com
Includes a library of articles covering presentation tips, tricks, and
technology. The site provides templates, clip art and sound clips,
as well as Presenters Services to use on the road. Even more
resources and services are available if you register to join the
Presenters Club—and it’s free.
Registration and Warranty
Your projector comes with a basic carry-in 2-year and 90-day lamp
warranty as well as an international warranty that let you project with
confidence anywhere in the world. For details, see page 94 and the
warranty brochure included with your projector.
In addition, for customers who register their projector, Epson offers
free Extra CareSM Road Service. In the unlikely event of an equipment
failure, you won’t have to wait for your unit to be repaired. Instead,
Epson will ship you a replacement unit anywhere in the United States
or Canada, usually via overnight delivery. See the brochure included
with your projector for details.
To register, simply fill out the registration card and mail it to Epson.
Or you can register online at http://www.epson.com/webreg.
Registering also lets you receive special updates on new accessories,
products, and service.
10 Welcome
Unpacking the Projector
After unpacking the projector, make sure you have all the parts shown
below:
Save all packaging in case you need to ship the projector. Always use
the original packaging (or the equivalent) when you need to send the
projector to another location. If you are moving the projector by
hand, use the carrying case. See page 11 for ordering information, and
page 66 for transportation instructions.
Additional Components
Depending on how you plan to use the projector, you may need
additional components:
■To receive an S-Video signal, you’ll need an S-Video cable. One
may be provided with your video equipment, or you can purchase
one from Epson; see below.
■To receive a component video signal from a VCR or other video
device, you’ll need an HD15 to component video cable. You can
purchase one from Epson; see below.
Projector
Remote control and
2 AAA batteries
Power cable VGA computer cable
Audio adapter
Carrying case
PDF manual and
registration CD-ROM
Welcome 11
Optional Accessories
To enhance your use of the projector, Epson provides the following
optional accessories:
You can purchase screens, carrying cases, or other accessories from an
Epson authorized reseller. To find the nearest reseller, call
800-GO-EPSON (800-463-7766). Or you can purchase online at
www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Product Part number
Replacement lamp V13H010L38
Air filter replacement set (2 filters) V13H13408
Universal ceiling mount
False ceiling plate
Security bracket/cabling for gyro lock mounts
Adjustable ceiling channel
Suspension adapter
ELPMBUNI
ELPMBFCP
ELPMBSEC
ELPMBACC
ELPMBAPL
Kensington® security lock ELPSL01
50-inch portable screen (4:3 aspect ratio)
60-inch portable pop-up screen (4:3 aspect ratio)
80-inch portable pop-up screen (4:3 aspect ratio)
83.6-inch hanging pull-down screen (4:3 aspect
ratio)
ELPSC06
ELPSC07
ELPSC08
ELPSC09
Component video cable
S-Video cable
ELPKC19
ELPSV01
Distribution amplifier ELPDA01
Image presentation camera (ELPDC05) V12H162020
13
1
Displaying and Adjusting
the Image
Whether you’re presenting from a computer or video equipment,
you need to follow some basic steps to display your image on the
screen.
Follow the guidelines in this chapter for:
■Positioning the projector
■Turning the projector on and selecting the image source
■Troubleshooting display problems
■Adjusting the image
■Turning off the projector
14 Displaying and Adjusting the Image
Positioning the Projector
If the projector isn’t already installed in the room you’re using, you’ll
probably want to place it on a table in front of the screen, as shown.
This lets you stand in the front of the room, face the audience, and
remain close enough to the equipment to be able to control it. Try to
leave as much space as possible between the projector and the screen to
get a good-size image.
Use the figure below to help you determine placement. Image size
increases with distance, but can vary depending on how you position
the zoom ring and whether you’ve adjusted the image with other
settings.
Also keep these considerations in mind:
■Place the projector on a sturdy, level surface.
■Make sure there is plenty of space for ventilation around and
under the projector. Do not set the projector on top of anything
that could block the vents under the projector.
■Make sure the projector is within 10 feet of a grounded electrical
outlet or extension cord.
note
You can mount the projector
on the ceiling, or place it
behind a translucent screen
for rear projection. See
page 81 for details.
3.2 to 3.9 ft6.6 to 7.9 ft33.1 to 39.7 ft Distance from screen
TBD
Displaying and Adjusting the Image 15
Ideally, you should place the projector directly in front of the center of
the screen, facing it toward the screen squarely. The base of the lens
should be at about the level of the bottom of the screen.
If you place the projector below screen level, you’ll have to tilt it up by
extending the front adjustable foot. This causes the image to become
“keystone” shaped, but you can correct the distortion by pressing the
buttons on the projector. See page 21 for detailed information about
correcting the image shape.
For instructions on installing the projector in a permanent location,
such as a theater or conference room, see page 81.
Projecting the Image
Make sure your projector and other equipment are set up as described
on page 33. Then follow the instructions below to start the projector
and display an image.
Turning On the Projector
Turn on any connected computer or video equipment before starting
the projector so it can automatically detect and display the image
source. If you turn on the projector first, or have multiple pieces of
connected equipment, you may have to select the image source
manually (see page 17).
note
After positioning the
projector, you may want to
connect a Kensington
MicroSaver® anti-theft
device to the lock port on the
projector. You can purchase
this from Epson; see
page 11.
Screen
Projector
16 Displaying and Adjusting the Image
Follow these steps to turn on the projector:
1. Open the A/V Mute slide (lens cover).
2. Plug one end of the power cable into the projector, and the other
end into an electrical outlet.
The Power light turns orange.
note
To shut down the projector,
see page 23. Shutting down
the projector correctly
prevents premature lamp
failure and possible damage
from overheating.
Power light
Displaying and Adjusting the Image 17
3. Press the red PPower button on the remote control or on top of
the projector.
The projector beeps once and the Power light flashes green as the
projector warms up, then an image begins to appear. When the
Power light stops flashing and remains green, the projector is
ready for use.
4. If you’ve connected a Windows-based computer to the projector,
you may see a New Hardware Wizard screen saying your
computer has found a plug-and-play monitor; if so, click Cancel.
5. If you are prompted to enter a password, see page 51.
Selecting the Image Source
Selecting the image source lets you switch between images input from
different pieces of connected equipment (such as a computer or DVD
player).
If you don’t see the image you want, press the Source Search button
on the projector or the Search button on the remote control until
you see the image you want to project.
You can also use the Source buttons on the remote control to switch
between devices connected to the ports identified on each button. The
PowerLite 1700c/1710c does not support EasyMP.
TM
warning
Never look into the lens
when the lamp is on. This
can damage your eyes, and is
especially dangerous for
children.
note
To focus and adjust the
image, see page 20. If a
projected image fails to
appear, see page 18 for help.
18 Displaying and Adjusting the Image
Troubleshooting Display Problems
Follow these guidelines if you’re having trouble displaying an image.
You Can’t Project an Image
If you don’t see the image you are trying to project, try the following:
■Make sure the cables are connected correctly, as described
beginning on page 33.
■Make sure the Power light is green and not flashing and the A/V
Mute slide is open.
■If you’ve connected more than one computer and/or video source,
you may need to press the Source Search button on the
projector’s control panel or Search button on the remote control
to select the correct source. (Allow a few seconds for the projector
to sync up after pressing the button.)
■If you’re using a PC notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be
labeled CRT/LCD or have an icon such as . You may have to
hold down the Fn key while pressing it. Allow a few seconds for
the projector to sync up after changing the setting.
The Projector and Notebook Don’t Display the
Same Image
If you’re projecting from a notebook, and you can’t see your image on
the projection screen and on your computer at the same time, follow
these guidelines.
If you’re using a PC notebook:
■On most systems, there’s a function key that lets you toggle
between the LCD screen and the projector, or display on both at
the same time. It may be labeled CRT/LCD or have an icon such as
. You may have to hold down the Fn key while pressing it.
Allow a few seconds for the projector to sync up after changing
the setting.
Displaying and Adjusting the Image 19
■If the function key doesn’t permit you to display simultaneously
on both screens, you should check your monitor settings to make
sure both the LCD screen and the external monitor port are
enabled.
From the Control Panel, open the Display utility. In the Display
Properties dialog box, click the Settings tab, then click
Advanced. The method for adjusting the settings varies by
brand; you may need to click a Monitor tab, then make sure the
external Monitor port is set as your primary display and/or
enabled. See your computer’s documentation or online help for
details.
If you’re using Mac OS X:
You may need to set up your system to display on the projector screen
as well as the LCD screen. Follow these steps:
1. From the Apple® menu, select System Preferences, then select
Displays.
2. Make sure the VGA Display or Color LCD dialog box is selected.
3. Click the Arrangement (or Arrange) tab.
4. Make sure the Mirror Displays checkbox is selected.
Make sure
Mirror Displays
is checked
20 Displaying and Adjusting the Image
Adjusting the Image
Once you see your image, you need to make certain adjustments:
■If the image is too high or too low, you can reposition it. See
below.
■To focus or zoom your image, see page 21.
■If the image isn’t square, see page 21.
■If a computer image displays incorrectly, see page 23.
■If you need to fine-tune the image and/or sound, see Chapter 4.
Adjusting the Height of Your Image
If the image is too low on the screen, you can use the front adjustable
foot to raise it.
1. Stand behind the projector. Press the blue foot release lever up
and lift the front of the projector.
2. Once the image is positioned where you want it, release the lever
to lock the foot in position.
3. If necessary, you can fine-tune the height or level the image by
turning the projector’s adjustable rear foot.
Raising the projector causes the image to distort or “keystone,” but
you can correct the shape as described on page 21.
Projector rear foot
Displaying and Adjusting the Image 21
Focusing and Zooming Your Image
Turn the focus ring on the projector to sharpen the image.
Turn the zoom ring on the projector to reduce or enlarge the image.
If the image still isn’t large enough, you may need to move the
projector farther away from the screen. You can also use the E-Zoom
buttons on the remote control to zoom in on a portion of the image.
See page 29 for instructions.
Adjusting the Image Shape
In most cases, you can maintain a square or rectangular image by
placing the projector directly in front of the center of the screen with
the base of the lens level with the bottom of the screen.
Even if the projector is slightly tilted (within a range of 30° up or
down), the projector has an automatic keystone correction function
that detects and corrects vertical keystone distortion.
It takes about one second after projection starts for the image to be
corrected. During this time, a vertical keystone correction gauge
appears on the screen.
If your image is still distorted, you can correct it using the Keystone
buttons on the projector’s control panel or the projector’s Setting
menu.
Focus Zoom
Corrected imageProjector tilted up Projector tilted down
Keystone correction
Displaying and Adjusting the Image 23
Correcting Computer Images
If you’re connected to a computer and the image doesn’t look right,
press the Auto button on the remote control or the Enter button on
the projector. This automatically resets the projector’s tracking, sync,
resolution, and position settings.
If the Auto button doesn’t correct the problem, you may need to
adjust the tracking or sync using the projector’s Signal menu. See
page 49 for more information.
Using the A/V Mute Slide
You can use the A/V Mute slide to temporarily turn off the image and
sound when you want to redirect your audience’s attention.
Shutting Down the Projector
When you’ve finished using the projector, follow the recommended
procedure to shut it down. This extends the life of the lamp and
protects the projector from possible overheating.
1. Turn off any equipment plugged into the projector.
2. To turn off the projector, press the red PPower button on the
remote control or projector.
note
You must be projecting an
image for this button to have
any effect. The Auto button
works only with computer
images projected through the
VGA port.
note
Lamp life results will vary
depending on mode selected,
environmental conditions,
and usage.
Turn off this product when
not in use to prolong the life
of the projector.
24 Displaying and Adjusting the Image
You see a confirmation message. (If
you don’t want to turn it off, press
any other button.)
3. Press the PPower button again. The
lamp turns off. When the projector beeps twice, you can unplug
the power cord.
(If the projector is mounted on the ceiling, you will need to wait
20 seconds for the projector to cool down before you can unplug
the power cord.)
If you want to turn the projector on again, make sure the orange
light is not flashing, then press the PPower button.
4. If you extended the adjustable front foot, press up on the blue
foot release lever to retract it.
5. Close the A/V Mute slide.
Using the Direct Power On Function
The Direct Power On function enables faster setup. The projector will
start up automatically when you plug it in; you won’t have to press the
PPower button.
Follow these steps to enable Direct Power On:
1. Press the Menu button on the remote control and select the
Extended menu.
2. Choose Operation and press Enter.
3. Choose Direct Power On and press Enter.
4. Highlight On and press Enter.
5. Press Esc or Menu to exit. The setting will take effect the next
time you plug in the projector.
note
You can set the projector to
automatically turn off the
projector lamp and enter
“sleep mode” when it has
not received any signals for
30 minutes. This conserves
electricity, cools the
projector, and extends the
life of the lamp. If you want
to start projecting again,
press the P Power button.
If you are done using the
projector, unplug the power
cord. To enable sleep mode,
see page 57.
note
If a power outage occurs
when Direct Power On is
enabled and the projector is
plugged in, the projector will
start when the power is
restored.
25
2
Using the Remote Control
The projector includes a number of tools to enhance your
presentation. All of them can be accessed using the remote control,
which lets you operate the projector from anywhere in the room—up
to 20 feet away.
You can use the remote control to adjust the picture and sound
(page 27) or as a pointer to highlight your presentation (page 32). You
can also use it to adjust the color mode for various environments
(page 30) or as a wireless mouse when projecting from a computer
(page 31).
This chapter covers:
■Using the remote control
■Controlling the picture and sound
■Operating your computer with the remote control
■Highlighting your presentation
note
For information and
resources to help you give
the most professional
p
resentation, be sure to visit
presentersonline.com.
26 Using the Remote Control
Using the Remote Control
Follow these tips for using the remote control:
■Point the remote control at the front of the projector or at the
screen.
■Stand within 20 feet of the projector.
■Avoid using the remote under bright fluorescent lamps or in
direct sunlight, or the projector may not respond properly.
Replacing the Batteries
Replace the batteries as described below:
1. Turn the remote control over.
2. Press down on the tab on the
battery cover as you lift the cover
off.
3. Install two AAA batteries,
inserting the + and – ends as
shown.
4. Position the cover as shown, then
press down until it snaps into
place.
note
If a button is pressed longer
than 30 seconds, the remote
control stops operating to
conserve power. When you
release the button, normal
operation resumes.
caution
When replacing batteries,
take the following
precautions:
■Replace the batteries as
soon as they run out. If the
batteries leak, wipe away
battery fluid with a soft
cloth. If fluid gets on your
hands, wash immediately.
■Do not expose batteries to
heat or flame.
■Dispose of used batteries
according to local
regulations.
■Remove the batteries if
you won’t be using the
projector for a long period of
time.
Using the Remote Control 27
Controlling the Picture and Sound
You can use the remote control to preview and select your picture
sources, temporarily turn off the picture and sound, freeze the action,
zoom in on the picture, and adjust the volume.
Switching Between Picture Sources
If your projector is connected to more than one computer and/or
video source, you can switch between the different sources:
■The easiest way to select your source is to press the Search button
on the remote control (or the Source Search button on the
projector) repeatedly until you see the image you want on the
screen.
■On the remote control, there are four Source buttons. Use them
to switch between equipment connected to the port identified on
each button
After you select a source, the screen goes dark for a moment before the
image appears.
Using the Remote Control 29
Zooming Part of Your Image
You can zoom in on a portion of the image using the E-Zoom buttons
on the remote control.
1. Press the E-Zoom button on the remote control.
You see a crosshair indicating the center of the zoom-in area.
2. Use the pointer button to position the crosshair.
3. Continue pressing the E-Zoom button to enlarge the selected
area up to 4 times.
4. While the image is enlarged, you can:
■Use the pointer button to move around the screen.
■Press the E-Zoom button to zoom out.
5. When done, press the ESC button to return the image to its
original size.
Controlling the Volume
To change the volume, press the or button on the remote
control or projector.
You can also adjust the volume using the projector’s menu system. See
page 50.
note
To temporarily shut off the
sound and picture, press the
A/V Mute button or close
the A/V Mute slide.
30 Using the Remote Control
Resizing Video Images
You can use the Resize button on the remote control to adjust how
an image fits into the display area.
For video images, press Resize to switch the aspect ratio between 4:3
and 16:9, (and Normal for computer images). This lets you play
certain digital video images or movies recorded on certain DVDs in
16:9 widescreen format.
For computer images, resizing is normally unnecessary, since the
projector automatically resizes the image to make the best use of the
display area. If you press the Resize button on the projector or remote
control, the projector displays the image at the output resolution of
the computer (which makes the image larger or smaller, depending on
its resolution). If the resolution of the image is the same as the
projector’s (1024 × 768), pressing Resize has no effect.
Adjusting the Color Mode
You can use the Color Mode button on the remote control to adjust
the color, brightness, and other aspects of your image.
Press the button repeatedly to select from the following settings:
Photo: For vivid, high-contrast still images in a bright room.
Sports (video, S-video, or composite video only): For vivid TV
images projected in a bright room.
Presentation: For computer presentations (the default when
projecting from a computer with analog video).
Theatre: For optimizing movie images with increased contrast.
Game: For increased brightness when playing video games or
watching TV in a bright room. Emphasizes dark gradations.
sRGB: For matching the color palette of standard sRGB computer
displays
Blackboard: For projecting accurate colors on a green chalkboard
(adjusts the white point).
Customized: For manual color adjustment. (See page 46).
Using the Remote Control 31
Operating Your Computer with the
Remote Control
If you connect a computer to the projector with a USB cable, as
described on page 35, then select Link21L for the USB Type B setting
in the Extended menu (see page 58), you can use the remote control
in place of your computer’s mouse. This gives you more flexibility
when delivering slideshow-style presentations, since you won’t have to
stand next to the computer to change slides.
■Use the Up and Down buttons to move through a
slideshow.
■Use the pointer button to move the cursor on the screen.
■Press the Enter button once to left-click, or press it twice to
double-click. Press the Esc button to right-click.
■To drag-and-drop, hold down the Enter button. Then use the
pointer button to drag the object. When it’s where you want it,
press Enter to release it.
Page up or down
to change slides
in PowerPoint
Right-click
Left-click
32 Using the Remote Control
Highlighting Your Presentation
You can display a pointer to call out important information on the
screen. If you want to customize the pointer tool, you can choose from
three alternative shapes.
Using the Pointer Tool
1. To activate the pointer tool, press the Pointer button on the
remote control. A pointer appears on the screen.
If you prefer to use a different style of pointer, see the instructions
in the next section.
2. Use the pointer button on the remote control to position the
pointer on the screen.
3. When you’re done using the pointer, press Esc to clear the screen.
Customizing the Pointer Tool
You can change the appearance of the pointer by choosing from three
alternative shapes.
1. Press the Menu button on the remote control, highlight the
Settings menu, highlight Pointer Shape, and press Enter. You
can select one of the pointer shapes shown at the left.
2. Select the shape you want and press Enter.
3. Highlight Return and press Enter.
4. Press Menu to exit from the menu system.
Pointer
33
3
Connecting to Computers
and Other Equipment
This chapter tells you how to connect the projector to a notebook or
desktop computer, and/or to video equipment, such as a VCR, DVD
player, or video camera.
Follow the instructions in this chapter on:
■Connecting to a computer
■Connecting video equipment
■Playing sound through the projector
34 Connecting to Computers and Other Equipment
Connecting to a Computer
You can connect the projector to any computer that has a standard
video output (monitor) port, including desktop models, PC notebook
and notebook computers, MacBooks, PowerBooks and iBooks, and
hand-held devices.
■To connect to the blue Computer/Component Video port
(standard VGA cable connection), see the instructions below.
Connecting to the Computer Port
You can connect to the blue Computer/Component Video port
using the VGA computer cable that came with the projector (the
monitor port on your computer must be a mini D-sub 15-pin port).
1. If you’re using the VGA computer cable, connect one end to the
projector’s blue Computer/Component Video port, and the
other end to your computer’s monitor port. Then go to step 3.
2. You can connect an optional stereo mini-jack audio cable to play
sound through the projector (see page 40), or connect a USB
cable to use the remote control as a mouse (see page 35).
note
If you connect a Windows-
based computer to the
projector, you may see a
New Hardware Wizard
saying your computer has
found a plug-and-play
monitor; if so, click Cancel.
caution
Don’t try to force a
connector to fit a port with a
different shape or number of
pins. You may damage the
port or connector.
Connecting to Computers and Other Equipment 35
3. When you’ve finished making any connections, see page 15 for
instructions on turning on the projector and adjusting the image.
Connecting the Cable for Remote Mouse
Control
If you’ve connected a computer as described in this chapter (using the
Computer/Component Video port) and set the USB Type B setting
under the projector’s Extended menu to Link21L (see page 58), you
can use the projector’s remote control as a wireless mouse. This lets
you control your computer and click through slideshow-style
presentations, such as PowerPoint, from up to 20 feet away.
The wireless mouse function is supported on systems with a USB port
running Windows XP, 98SE, Me, or 2000, or Mac OS X 10.2.x to
10.4.x. This function is not supported if you use an S-Video cable to
connect your computer to the projector.
1. Locate the USB cable that came with your projector.
2. Connect the square end of the cable to the projector’s
USB port.
3. Connect the flat end of the cable to any available USB port on
your notebook or desktop computer.
4. If necessary, configure your computer to work with an external
USB mouse. See your computer documentation for details.
note
For details on how to use the
remote control in place of
your computer’s mouse, see
page 31.
Move
cursor
Left-
click
Right-
click
note
The remote mouse control
function may not operate
correctly on systems that
have been upgraded from an
earlier version of Windows.
USB cable
36 Connecting to Computers and Other Equipment
Connecting to Video Equipment
You can connect several video sources to the projector at the same
time. Before starting, look at your video equipment to determine its
available video output connections:
■If your video player has a yellow RCA-style video output
connector, see “Connecting a Composite Video Source” on
page 37.
■If your video player has an S-Video connector, see “Connecting
an S-Video Source” on page 38.
■If your video player has a component video port (three connectors
labeled either Y/Cb/Cr or Y/Pb/Pr), see “Connecting a
Component Video Source” on page 39.
■If your video player has an RGB video port (either a single
connector for a VGA-style monitor cable or three connectors
labeled R/G/B), see “Connecting an RGB Video Source” on
page 40.
After connecting video cables, you may also want to connect an audio
cable to play sound through the projector; see page 40.
RCA connector
(composite video)
S-Video
connector
VGA connector
(RGB video)
Connecting to Computers and Other Equipment 37
Connecting a Composite Video Source
1. Locate an RCA-style video cable (one is usually provided with
your video equipment or you can purchase one from an
electronics dealer).
2. Connect the cable to the yellow video output connector on your
player and the yellow Video connector on the projector:
3. If you want to play sound through the projector, see page 40 for
instructions on connecting audio cables.
4. If you don’t need to make any other connections, see page 15 or
the Quick Setup sheet for instructions on turning on the projector
and adjusting the image. Once the projector is turned on, select
the image source: press the Search button on the remote control
or press the Source Search button on the projector’s control
panel repeatedly until the image appears.
38 Connecting to Computers and Other Equipment
Connecting an S-Video Source
1. Locate an S-Video cable (one is usually provided with your video
equipment or you can purchase one from Epson; see page 10).
2. Connect the cable to the S-Video connector on your player and
the S-Video connector on the projector:
3. If you want to play sound through the projector, see page 40 for
instructions on connecting audio cables.
4. If you don’t need to make any other connections, see page 15 or
the Quick Setup sheet for instructions on turning on the projector
and adjusting the image. Once the projector is turned on, select
the image source: press the Search button on the remote control
or press the Source Search button on the projector’s control
panel repeatedly until the image appears.
Connecting to Computers and Other Equipment 39
Connecting a Component Video Source
You will need a component-to-VGA video cable or a component
video-to-VGA adapter for this connection. You can order the
component-to-VGA cable (ELPKC19) from Epson; see page 11 for
more information.
1. Locate a component-to-VGA video cable or adapter.
2. Connect the cable to your player and the blue
Computer/Component Video connector on the projector.
3. If you want to play sound through the projector, see page 40 for
instructions on connecting audio cables.
4. If you don’t need to make any other connections, see page 15 for
instructions on turning on the projector and adjusting the image.
Once the projector is turned on, select the image source: press the
Search button on the remote control or press the Source
Search button on the projector’s control panel repeatedly until
the image appears.
note
Be sure your video player is
not an RGB video source.
If you select the wrong
source, image quality may
suffer. Check your video
player’s documentation.
Also, make sure the
Computer Input setting in
the Signal menu is set to
Auto or Component Video
(see page 49).
Component-to-VGA cable
(ELPKC19)
Component-to-
VGA adapter
40 Connecting to Computers and Other Equipment
Connecting an RGB Video Source
1. Locate the VGA computer cable provided with the projector.
2. Connect the cable to the video port on your player and the
Computer/Component port on the projector.
3. If you want to play sound through the projector, see page 40 for
instructions on connecting audio cables.
4. If you don’t need to make any other connections, see page 15 for
instructions on turning on the projector and adjusting the image.
Once the projector is turned on, select the image source: press the
Search button on the remote control or press the Source
Search button on the projector’s control panel repeatedly until
the image appears.
Playing Sound Through the Projector
You can play sound through the projector’s speaker system.
To play sound through the projector, follow these steps:
1. Locate the appropriate cable and connect it to the Audio jack on
the projector.
note
Be sure your video player is
not a component video
source. If you select the
wrong source, image quality
may suffer. Check your
video player’s
documentation.
Connecting to Computers and Other Equipment 41
■If you have a computer connected to the blue Computer/
Component Video port, use a stereo mini-jack cable.
■If you have video equipment connected to the Video or
S-Video port, use an RCA-style audio cable and the audio
adapter included with the projector.
2. Connect the other end of the cable to the audio output
connector(s) on your computer or video equipment.
Audio
adapter
42 Connecting to Computers and Other Equipment
43
4
Fine-Tuning the Projector
You can use the projector’s on-screen menus to adjust the image,
sound, and other features. This chapter covers the following
information:
■Using the menu system
■Adjusting the image
■Adjusting signal settings
■Customizing projector features
■Using the projector security features
■Customizing power and operation
44 Fine-Tuning the Projector
Using the Menu System
You can use the remote control or the projector’s control panel to
access the menus and change settings. Follow these steps:
1. To display the menu screen, press the Menu button on the
remote control or on the projector.
You see a menu screen similar to the one below:
The menus are listed on the left and the options available for the
highlighted menu are shown on the right.
2. Use the pointer button on the remote control (or the
navigational buttons on the projector) to scroll through the menu
list. When you’ve highlighted the desired menu, press the Enter
button to select it.
3. Once you’ve selected the menu, use the pointer button to
scroll through the list of options. (Some of the options may be
grayed out or unavailable, depending on the selected source.)
note
The Network option does
not appear in the
1700c/1710c menu. Menu list
Options
Fine-Tuning the Projector 45
4. After highlighting the option you want to adjust, use the
pointer button to change the setting. In some cases, you may
have to press the Enter button to view a sub-screen for changing
the setting.
■Press the left or right side of the pointer button to adjust
a slider bar.
■To select from two or more settings, use the pointer
button to highlight the desired setting and press Enter.
5. After changing the settings, press the Esc button to save your
changes and return to the previous menu (or press it repeatedly to
exit the menu system).
You can also press the Menu button to exit.
Restoring the Default Settings
You can use the menu system’s Reset options to restore the factory-
default settings for all the settings listed in a specific menu, or all the
settings in all menus.
To restore the settings in a specific menu, enter the menu whose
settings you want to change, select Reset, and confirm as needed.
(The example below shows how to reset the Image menu.)
To restore all the projector settings to their factory-default values,
select the Reset menu, highlight Reset All, and press Enter.
Reset settings
for current menu
Reset settings for
all menus
note
When you select Reset All
in the Reset menu, it does
not reset the Computer
Input, Video Signal, User’s
Logo, Language, or Lamp
settings.
Fine-Tuning the Projector 47
Blackboard: For projecting accurate colors on a green
chalkboard (adjusts the white point).
Customized: For manual color adjustment. (See below.)
■Brightness
Lightens or darkens the overall image.
■Contrast
Adjusts the difference between light and dark areas.
■Color Saturation (video only)
Adjusts the color depth of the image.
■Tint (video only)
Adjusts the balance of green to magenta in the image
(available only for component video or NTSC signals).
■Sharpness
Adjusts the sharpness of the image.
■Color Adjustment
Adjusts the color values. For Customized color mode, select
RGBCMY to adjust individual red, green, blue, cyan,
magenta, and yellow hue and saturation values. For other
color modes, RGB may be selected to adjust red, green, and
blue hue and saturation values. (Not available if sRGB is
selected as the Color Mode setting.)
■ABS Color Temp.
Sets a color temperature between 5000 and 10000 °K. (Not
available if sRGB is selected as the Color Mode setting.)
Six-Axis Color Adjustment
For special projection material, such as high-quality photographs or
artwork, you can adjust the hue and saturation for six different color
axes.
1. Follow the instructions on page 46 to open the Image menu and
select Color Mode.
2. Press the Enter button to select Customized, then press Esc to
return to the Image menu.
note
The Brightness setting
changes the opacity of the
projector’s LCD panels. You
can also change the lamp’s
brightness. Select
Brightness Control in the
Setting menu, then choose
High or Low (the default
setting is High).
48 Fine-Tuning the Projector
3. Select Color Adjustment and press Enter. You see hue and
saturation controls on the screen for six colors: RGBCMY (red,
green, blue, cyan, magenta, and yellow.
4. Select the color axis you want to adjust and press Enter. You see
color controls for hue and saturation.
Hue changes the balance of color, and saturation changes the
strength of the color.
5. Use the pointer button to adjust the hue and saturation. You
see the adjustments reflected on the screen. When you are satisfied
with the color, press Esc.
6. Repeat steps 4 and 5 for each color axis you want to adjust.
You may need to readjust the color as the lamp in your projector
changes over time.
Adjusting Signal Settings
Although the projector normally detects and optimizes the input
signal automatically, you can use the Signal menu to make manual
adjustments. In addition to changing the position of the projected
image, you can correct tracking and sync for computer images, or
change the aspect ratio to widescreen format for video images.
1. Press the Menu button and select the Signal menu.
You see a screen similar to one of those below. (The settings will
be different depending on the source you are projecting from.)
note
You can also use the remote
control’s Auto button to
automatically reset the
projector’s tracking, sync,
resolution, and position
settings. See page 23 for
details.
Computer/RGB Video Component Video Composite Video/S-Video
Fine-Tuning the Projector 49
2. Use the pointer button to highlight the desired option, then
adjust it as needed:
■Auto Setup
Leave this setting On to automatically optimize the computer
image. Turn it off if you want to save adjustments you have
made to the video settings.
■Tracking
Adjust this value to eliminate vertical stripes in the image.
■Sync
Adjust this value if the image appears blurry or flickers.
■Progressive
Turn this setting On to convert composite video signals into
progressive signals (best for still images). Leave the setting Off
for moving images.
■Position
If the image is slightly cut off on one or more sides, it may not
be centered exactly. Select this setting and use the pointer
button to center it.
■Computer Input
If the colors don’t look right on the Auto setting, select the
setting for the type of equipment you’ve connected to the
Computer/Component Video port:
RGB: For a computer connection.
Component Video: For a video player that outputs a
component video signal.
■Video Signal
Leave this setting at Auto unless you are using a 60-Hz PAL
system (then select PAL60).
■Resize
Choose an aspect ratio of either 4:3 or 16:9. Normal is the
default setting for a computer connection.
tip
Before adjusting tracking or
sync, fill the screen with an
image containing fine
detail. For example, in
Windows you can select a
pattern to appear as your
desktop background. If this
option isn’t available, try
projecting black text on a
white background.
50 Fine-Tuning the Projector
Customizing Projector Features
You can use the Settings menu to lock the buttons on the projector,
adjust audio volume, and customize several other features.
■Keystone
Squares up the shape of the image after the projector has been
tilted upward. If you notice lines or edges looking jagged after
adjusting the shape, decrease the Sharpness setting (see page 46).
■Auto Keystone
Automatically compensates for keystone distortion when the
projector is tilted upward. This feature is available only when the
projector is set for front projection (it is enabled by default).
■Operation Lock
Lets you disable all of the buttons on the projector except the
PPower button. See page 56 for more information.
■Pointer Shape
Lets you choose from three alternative pointer shapes. See page 32
for more information.
■Brightness Control
Lets you select from two levels of brightness. The Low setting
reduces power consumption and noise, and extends the lamp’s
operating life.
■Volume
Raises or lowers the volume of the projector’s speaker.
note
You can also adjust the
volume using the remote
control.
Fine-Tuning the Projector 51
Using the Projector Security Features
To prevent unauthorized use of the projector, you can do the
following:
■Assign a password; this can be disabled for a set period if you want
to loan the projector to someone.
■Create an identifying user logo that is displayed at startup and/or
when the A/V Mute button is pressed. See page 54.
■Disable the projector’s buttons; this is useful, for example, if
you’re projecting in a classroom and you want to ensure that no
one touches the projector’s buttons while you’re using the remote
control. See page 56.
If you create a user’s logo for the projector, you can set up the logo so
it is displayed as the startup screen and/or AV/Mute screen.
Unauthorized users cannot turn it off or change it. This feature is
intended to discourage theft and provides a way to identify the
projector should it be stolen.
Enabling Password Protection
To prevent unauthorized use, you can assign the projector a password.
If you do, a screen will appear requesting the password whenever the
projector is plugged in and turned on. If an incorrect password is
entered three times in succession, the projector’s operation is locked
and the power cord must be disconnected and reinserted to redisplay
the password screen. If an incorrect password is entered thirty times in
succession, the user must contact Epson to unlock the projector.
The default setting for the Password Protect function is Off. Follow
these steps to turn password protection on:
1. Press the Freeze button on the remote control for about five
seconds.
note
It’s a good idea to write
down your password.
If you leave the projector
plugged in, the Password
Protect Release screen will
not appear. You only need a
password if you unplug and
reconnect the power cable.
Network Protect is not
available for the
1700c/1710c projector.
Fine-Tuning the Projector 53
10. To enable your screen logo, select User’s Logo Protect and press
Enter. Select On and press Enter.
When this feature is on, the logo appears whenever you turn on
the projector (if the Startup Screen is enabled in the Extended
menu; see page 54). It also appears when you press the A/V Mute
button (if you selected the Logo for the A/V Mute setting under
Display in the Extended menu). None of the User’s Logo features
in the Extended menu can be changed when the User’s Logo
Protect function is enabled.
Starting the Projector with a Password
When the password function is enabled, you see this screen when you
plug in and turn on the projector:
Hold down the Num button on the remote control and use the
numeric keypad to enter the four digit password.
The password screen closes, the numeric keypad is automatically
deactivated, and projection begins.
If the password is not correct, you see a message prompting you to
re-enter the password. If you enter an incorrect password three times
in succession, you see the message The projector’s operation will be
locked. Request code xxxxx and the projector switches to standby
mode for approximately 5 minutes. Write down the request code.
Then disconnect the projector’s power cord from the electrical outlet,
reconnect it, and turn the projector back on.
When you see the Password Protect Release screen again, you can try
to enter the correct password.
Fine-Tuning the Projector 55
4. Use the pointer button to select the area of the image you
want to use. Then press Enter.
5. When you see the message Select this Image?, highlight Yes
and press Enter.
6. Use the arrow buttons to select a zoom rate (display size) and press
Enter.
7. When the message Save this image as the user’s logo?
appears, select Yes and press Enter. Saving the logo may take a
few moments. Do not use your projector, remote control, or
video source while the logo is being saved.
8. When you see the message Completed, press Esc to return to the
menu screen.
56 Fine-Tuning the Projector
Choosing When to Display the Image
After your image is saved, it is automatically set as the startup screen.
You can also set it to display as the screen you see when there’s no
signal or when you press the A/V Mute button (see page 28).
1. Press the Menu button, highlight the Extended menu, and press
Enter.
2. Select Display and press Enter.
3. Highlight Display Background (for when there is no signal) or
A/V Mute, and press Enter.
4. Select Logo and press Enter.
5. When you’re finished, press Esc to exit.
Disabling the Projector’s Buttons
When you enable the Operation Lock function, you can lock all the
projector’s buttons, or all buttons except the Power button.
1. Press the Menu button, highlight the Settings menu, and press
Enter.
2. Select Operation Lock and press the Enter button.
3. Select Full Lock (to lock all projector buttons) or Partial Lock (to
lock all buttons except the Power button) and press Enter.
4. Select Yes and press Enter to confirm the setting.
5. Press the Menu button to exit.
note
Press the Enter button on
the projector’s control panel
for 7 seconds to disable the
Operation Lock function.
Fine-Tuning the Projector 57
Customizing Power and Operation
You can use the Extended menu to customize the way the projector
displays images, enable quick startup, turn sleep mode on or off, and
customize other projector operations.
■Display
Use this setting to turn off the display of messages, change the
background color, enable logo display, or turn off the startup
screen display.
■User’s Logo
Create a custom startup screen, as described on page 54.
■Projection
Select Front (to project from the front of a screen and right side
up), Front/Ceiling (when the projector is mounted upside-down
from the ceiling), Rear (to project from behind onto a
transparent screen), or Rear/Ceiling (to project from behind onto
a transparent screen when the projector is mounted upside-down
from the ceiling).
When you select one of the Ceiling projection methods, the
projector requires a 10-second cool-down after you turn it off.
You need to wait until you hear the projector beep before
unplugging it.
■Operation
Enable Direct Power On if you want to have the projector start
when the power cable is connected (without pressing the Power
note
If Direct Power On is
enabled, the power cable is
connected, and a power
outage occurs, the projector
will start when the power is
restored.
Do not use the projector at
altitudes above 7500 ft
(2,286 m).
58 Fine-Tuning the Projector
button). Enable Sleep Mode if you want to have the projector
turn off automatically if it is idle (and no signal is received) for 30
minutes or when the A/V Mute Slide is Closed. Enable High
Altitude Mode when you are using the projector above 4900 ft
(1500 m).
■Link 21L
This setting is available only if you select Link21L for the USB
Type B setting. Select Off if you want to use the remote as a
wireless mouse for a USB-connected computer. See page 35 for
more information.
■Language
Select from nine languages to be used for the projector menus.
Specyfikacje produktu
| Marka: | Epson |
| Kategoria: | Projektor Beamer |
| Model: | powerlite 1710c multimedia projector |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Epson powerlite 1710c multimedia projector, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Projektor Beamer Epson
2 Września 2024
31 Sierpnia 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
4 Lipca 2024
Instrukcje Projektor Beamer
- Projektor Beamer Sony
- Projektor Beamer Yamaha
- Projektor Beamer Philips
- Projektor Beamer Acer
- Projektor Beamer Nobo
- Projektor Beamer Panasonic
- Projektor Beamer Canon
- Projektor Beamer Viewsonic
- Projektor Beamer Medion
- Projektor Beamer Toshiba
- Projektor Beamer Casio
- Projektor Beamer HP
- Projektor Beamer Kodak
- Projektor Beamer JVC
- Projektor Beamer Dell
- Projektor Beamer Auna
- Projektor Beamer Mitsubishi
- Projektor Beamer XGIMI
- Projektor Beamer NEC
- Projektor Beamer Sanyo
- Projektor Beamer Optoma
- Projektor Beamer Nebula
- Projektor Beamer BenQ
- Projektor Beamer Overmax
- Projektor Beamer Fenton
- Projektor Beamer Aiptek
- Projektor Beamer Apeman
- Projektor Beamer Sagem
- Projektor Beamer Eiki
- Projektor Beamer InFocus
- Projektor Beamer Bauer
- Projektor Beamer Aaxa
- Projektor Beamer Vivitek
- Projektor Beamer Brookstone
- Projektor Beamer Stereoboomm
- Projektor Beamer Ibm
- Projektor Beamer Legamaster
- Projektor Beamer La Vague
- Projektor Beamer FengMi Wemax
- Projektor Beamer Nor-tec
- Projektor Beamer Skytronic
- Projektor Beamer Eumig
- Projektor Beamer DreamVision
Najnowsze instrukcje dla Projektor Beamer
15 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
12 Stycznia 2025
17 Grudnia 2024
5 Października 2024
5 Października 2024
5 Października 2024