Instrukcja obsługi Epson ELPMBP02

Epson Projektor ELPMBP02

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Epson ELPMBP02 (6 stron) w kategorii Projektor. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/6
Model: ELPMBP02 This product is UL Listed. It must be
installed by a qualified professional
installer.
R
Installation and Assembly:
False Ceiling Plate Kit
3215 W. North Ave. Melrose Park, IL 60160 (800) 865-2112 or (708) 865-8870 Fax: (708) 865-2941 www.peerlessmounts.com
Maximum UL Load Capacity: ( )50 lb 22.6 kg
Manufactured by Peerless Industries, Inc.
ISSUED: 02-13-08 SHEET #:128-9030-2 07-16-08
2 of 6
Visit the Peerless Web Site at www.peerlessmounts.com For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
Table of Contents
Parts List .............................................................................................................................................................................. 3
Mounting Above Ceiling Tile, Mounting in Place of Ceiling Tile and Attaching Ceiling Tray to Filler Tray ............................... 4
Anchoring Methods ............................................................................................................................................................... 5
Warranty Information ............................................................................................................................................................. 6
NOTE: Read entire instruction sheet before you start installation and assembly.
Do not begin to install your product until you have read and understood the instructions and warnings contained in this
Installation Sheet. If you have any questions regarding any of the instructions or warnings, call Peerless customer care
at 1-800-729-0307.
This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard-
ware and components.
Never exceed the Maximum UL Load Capacity.
If mounting to wood joists or wood beam ceilings, make sure that mounting screws are anchored into the center of the
joists or beams. Use of an "edge to edge" stud finder is highly recommended.
Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
When installing or adjusting the ceiling mount, do not use adhesives, lubricants or oils to prevent the screws from
loosening. If you use adhesives, lubricants, or oils to prevent the screws from loosening, the casing may crack and the
projector may fall, causing serious injury and damage to the projector.
WARNING
Tools Needed for Assembly
stud finder ("edge to edge" stud finder is recommended)
phillips screwdriver
hammer
wire cutters
drill
1/4" bit for concrete surface
5/32" bit for wood studs
ISSUED: 02-13-08 SHEET #:128-9030-2 07-16-08
3 of 6
Visit the Peerless Web Site at www.peerlessmounts.com For Technical Support Contact Peerless Mounts at 1-800-729-0307 or 708-865-8870.
A1
NOTE: Some parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.
D
B C
A
LKF
MAA BB
CC
IMPORTANT PRE-ASSEMBLY INFORMATION: Ceiling Trays (A), and (A1) are designed to fit within or above a
24" (610 mm) x 24" (610 mm) section of a conventional suspended ceiling system. It may also be mounted within or
above 24" x 48" conventional suspended ceiling. Ceiling runners (see DETAIL 1, page 5) should have a "T" cross
section and a minimum height of 1.5" (38 mm).
For certain installations it may be best to install ceiling anchors (step 2) before installing the ceiling tray (step 1).
Description Qt
y
. Part #
A
ceiling tray 1 128-2198
A1 filler tray 1 128-2207
B1/4"-20 x 3/8" screws 4 520-2015
C1/4"-20 nuts 4 530-9302
Dallen wrench 1 560-9706
Fturnbuckle 4 560-9620
G12 gauge x 20' (6.1m) tie wire (not shown) 1 600-2008
Keye bolt 5 580-0006
Lconcrete anchor 5 580-0005
Mflush mount tube 1 1446-014
A
A
M5 x 10 mm socket screw 4 520-1216
BB nut 4 530-9409
CC 3 mm allen wrench 1 560-0194
Parts List


Specyfikacje produktu

Marka: Epson
Kategoria: Projektor
Model: ELPMBP02

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Epson ELPMBP02, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Projektor Epson

Epson

Epson PowerLite 5520W Instrukcja

13 Października 2024
Epson

Epson EX3220 Instrukcja

12 Października 2024
Epson

Epson EH-LS500W Instrukcja

10 Października 2024
Epson

Epson ELPMB84 Instrukcja

7 Października 2024
Epson

Epson ELPMB85 Instrukcja

7 Października 2024
Epson

Epson ELPMB64 Instrukcja

7 Października 2024
Epson

Epson ELPMB79 Instrukcja

7 Października 2024

Instrukcje Projektor

Najnowsze instrukcje dla Projektor

Acer

Acer X137WH Instrukcja

14 Października 2024
Hitachi

Hitachi CP-A352WNM Instrukcja

14 Października 2024
Barco

Barco Thor Instrukcja

14 Października 2024
NEC

NEC NP-M283X Instrukcja

14 Października 2024
Acer

Acer X112 Instrukcja

12 Października 2024
3M

3M X36i Instrukcja

11 Października 2024
Optoma

Optoma EP774 Instrukcja

11 Października 2024
Sanyo

Sanyo PLC-8810N Instrukcja

11 Października 2024
Barco

Barco F70-W6 Instrukcja

10 Października 2024
NEC

NEC NP-M363X Instrukcja

10 Października 2024