Instrukcja obsługi Epcom X6465A

Epcom Niesklasyfikowane X6465A

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Epcom X6465A (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
A low prole LED beacon with a long, maintenance-free
service life. These beacons are ideal for industrial vehicle
applications and feature a 12-80 VDC operating range.
Do not install and/or operate this safety product unless you have read and understand the
safety information contained in this manual.
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices
are essential to ensure the safety of you and those you are trying to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause
high current arcing, which can cause personal injury and/or severe vehicle damage, including re.
4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output
performance of the system is maximized and the controls are placed within convenient reach of the operator so that
s/he can operate the system without losing eye contact with the roadway.
5. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In
use, the vehicle operator should ensure the projection of the warning signal is not blocked by vehicle components (i.e.,
open trunks or compartment doors), people, vehicles, or other obstructions.
6. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal.
Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an
intersection, driving against trafc, responding at a high rate of speed, walking on or around trafc lanes.
7. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obey-
ing all laws regarding warning signal devices. Therefore, the user should check all applicable city, state, and federal
laws and regulations. The manufacturer assumes no liability for any loss resulting from the use of this warning device.
WARNING!
Failure to install or use this product according to manufacturer’s recommendations may result in property
damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect!
!
Page 1 of 3
Installation and Operation Instructions
LED Beacon
Specications:
Size: Permanent Mount W: 5.1” x H: 4.2”
Magnet Mount W: 5.1” x H: 4.3”
Weight: Permanent Mount 0.6 lb.
Magnet Mount 1.6 lb.
Voltage: 12-80 VDC systems
Current Draw: 150 mA
Pulse 8: 85 FPM
Important! This unit is a safety device, and it must be con-
nected to its own separate, fused power point to assure its
continued operation should any other electrical accessory fail.
Page 2 of 3
WARNING!
Maximum recommended vehicle speed for safe oper-
ation using the Magnet Mount model is 65 mph (104
km/h) on a well maintained road, when tted to the
center of a vehicle roof of steel construction. Higher
speeds could cause the mount to fail, resulting in the
beacon ying off of the vehicle, which could cause
damage to other vehicles and injury or death to the
passengers.
The magnet mount is not intended as a permanent mounting
for the beacon. The magnet mount unit must be mounted on
a magnetic surface (i.e. no berglass, etc.). Insure that the
magnet is kept clean.
!
Installation & Mounting:
Carefully remove the beacon and place it on a at surface. Ex-
amine the unit for transit damage, broken lenses, etc. If damage
is found, contact the transit company or distributor. Do not use
damaged or broken parts.
Mounting:
Permanent
Position the unit in the desired mounting location. Using the base
as a template, mark the mounting hole locations. Drill three 3/16”
mounting holes, and drill one hole for power wire routing. The use
of a grommet is recommended for wires passing through compart-
ment walls. Mount the beacon using #10 hardware.
Mounting:
Temporary, magnet
Comes complete with a magnet, a fteen foot cord and a ciga-
rette lighter plug. A magnet mount kit is also available.
Note: These units are not sealed on the bottom. For
operation in an extremely moist environment or as added
protection against moisture, sealing the wire exit hole on
the bottom with a pliable caulking material is
recommended.
Note: Operating the vehicle without the lens installed on the
product may result in damage that will NOT be covered under
warranty
Wiring:
The wiring for this conguration is as shown in Figure 1 below.
The positive line must have a 3 amp fuse, as shown. A switch
may be used to control the on/off function
.
RED WIRE
SWITCH
(USER SUPPLIED)
FUSE (3 AMP)
(USER SUPPLIED)
BATTERY
GROUND GROUND
BLACK WIRE
CAUTION: HIGH VOLTAGE. Before servicing light, turn
“OFF” power and wait ve minutes.
920-1022-01 Rev. A Page 3 of 3
Manufacturer Limited Warranty and Limitation of Liability:
Manufacturer warrants that on the date of purchase this product will conform to Manufacturer’s specications for this product (which are
available from the Manufacturer upon request), and Manufacturer further warrants that this product is free from defects in materials and
workmanship. This Limited Warranty extends for thirty six (36) months from the date of purchase. Manufacturer will, at its discretion, repair
or replace any product found by the Manufacturer to be defective and subject to this Limited Warranty.
DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED
MODIFICATIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCOR-
DANCE WITH THE MAINTENANCE PROCEDURES SET FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING INSTRUC-
TIONS VOIDS THIS LIMITED WARRANTY.
ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT WHICH MAY HAVE BEEN MADE BY SALESPEOPLE, DEAL-
ERS, AGENTS OR OTHER MANUFACTURER’S REPRESENTATIVES DO NOT CONSTITUTE WARRANTIES. THIS LIMITED WAR-
RANTY MAY NOT BE AMENDED, MODIFIED, OR ENLARGED EXCEPT BY A WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED
OFFICIAL OF MANUFACTURER WHICH EXPRESSLY REFERS TO THIS LIMITED WARRANTY.
Exclusion of Other Warranties:
MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT. BUYER’S
SOLE AND EXCLUSIVE REMEDY IN CONTRACT, TORT, OR UNDER ANY OTHER THEORY AGAINST MANUFACTURER REGARDING
THE PRODUCT AND ITS USE SHALL BE THE REPLACEMENT OR REPAIR OF THE PRODUCT AS DESCRIBED ABOVE.
Limitation of Liability:
IN THE EVENT OF LIABILITY FOR DAMAGES ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM RELATED TO
THE MANUFACTURER’S PRODUCTS, MANUFACTURER’S LIABILITY FOR DAMAGES SHALL BE LIMITED TO THE AMOUNT PAID
FOR THE PRODUCT AT THE TIME OF THE ORIGINAL PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST
PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL,
OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE,
OR OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS BEEN ADVISED OF THE POS-
SIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT TO THE
PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMP-
TION OF ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.
This Limited Warranty denes specic legal rights. You may have other legal rights which vary from state to state. Some states do not allow
the exclusion or limitation of incidental or consequential damages.
www.syscom.mx

Specyfikacje produktu

Marka: Epcom
Kategoria: Niesklasyfikowane
Model: X6465A

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Epcom X6465A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Epcom

Epcom

Epcom X67-R Instrukcja

30 Września 2024
Epcom

Epcom X303N Instrukcja

30 Września 2024
Epcom

Epcom XLL-1088-RB Instrukcja

30 Września 2024
Epcom

Epcom GT-003 Instrukcja

30 Września 2024
Epcom

Epcom X12BW Instrukcja

30 Września 2024
Epcom

Epcom X7945A Instrukcja

30 Września 2024
Epcom

Epcom XLS-100 Instrukcja

30 Września 2024
Epcom

Epcom X3225 Instrukcja

30 Września 2024
Epcom

Epcom X606-A Instrukcja

30 Września 2024
Epcom

Epcom X6262A Instrukcja

30 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024