Instrukcja obsługi Elro SX32 Deurbel

Elro dzwonek do drzwi SX32 Deurbel

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Elro SX32 Deurbel (1 stron) w kategorii dzwonek do drzwi. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/1
Wire Free Converter
SX-32
Battery Installation
1. The Converter unit is operated by 1 x 12 volt battery (23A - included).
2. Remove the back of the case by pushing in the tab on the bottom with a
small, flat screwdriver.
3. Insert 1 x 12 volt battery (23A - included) in the battery compartment, ensuring
the battery’s polarity matches the internal markings.
4. Snap the front cover of push button back on, then it is ready to use.
Installation Guide
1) Westminster - 8 notes
2) Ding-Dong - Repeat
3) Telephone Ring
4) Circus Theme
Melody Selection (On selected Models)
The Melody selector is located inside the push converter unit, a small switch on the
top left corner of battery compartment marked with “S”. Press the switch once, the
melody will change to the netxt one on the list, there are a total of 8 melodies for
selection. The converter is pre-set to “Westminster” therefore, if no change is
required, it should not be adjusted.
5) Banjo on my knee
6) Twinkle, Twinkle
7) It’s a small world
8) Dog Barking
1. Drill hole and fit wall plug (if fixing to masonry) and screw (self-tapping N3 x 16mm
screw) to fixing position. Leave a gap of 3mm between the screw head and the wall.
Locate the keyhole slot on the back of the unit, over the screw.
Important: Mounting the Converter unit on metal or UPVC doorframes will seriously
reduce the operating range.
2. Then use the second hole located at the bottom half of the Converter as a template,
mark the fixing position for the unit. Drill hole and fit wall plug and secure the Converter
Unit with the screw (self-tapping N3 x 16mm screw) in position.
3. Alternatively, use the double-sided self-adhesive pad (included) to attach the converter
to the fixing position between the bell push and door chime unit.
Note: When mounting to masonry, fit wall plugs. When mounting to wooden doorframe
wall plugs are not necessary.
In case a Transformer (A/C 8v) is used to power the Wired Bell
Push and Wired Door Chime.
1. Remove the back of case by pushing in the tab on the botton
with a small, flat screwdriver.
2. Disconnect the wire that connected with Wired Door Chime.
3. Feed the wire via the hole on the back of the Converter,
connect the wire to the terminal positions marked below.
4. Snap the front cover of push button back on, then it is ready
to use.
Important: Do not connect the Converter unit with any Lighted
Bell Push.
Operation
When the wired Bell Push is pressed, it will activate the
Converter and transmit a wireless signal for 1 second to the
Wireless Door Chime, Green LED light will light up as operation
indication, and the door chime will sound.
Important
1. Do not mount the Converter unit onto any metal surface or metal doorframe including UPVC.
2. Do not expose the unit directly to rain or immerse either in water.
3. Do not expose the unit to high temperatures or close to fireplace.
4. Do not leave exhausted batteries in either unit.
5. Do not connect the Converter unit with any Lighting Bell Push.
6. Converter is designed for internal use only.
7. Please dispose of old, defective batteries in and environmentally friendly manner in accordance with the
relevant legislation.
8. Make sure that no naked flame sources, such as lighted candles, should be placed on the unit.
9. The unit should not be exposed to dripping or splashing and that no objects filled with liquids.
10. Replace only with the same or equivalent type battery recommended by the manufacturer.
Specification
Converter unit
Power
Consumption
Operating Temperature
Operating Distance
Selectable Tone
Selectable Channel
: 1 x 12volt 23A battery (included) Replace with Byron SD100 model.
: 3.0mA - ON
0.003mA - OFF
: -10°C to +40°C
: 100 metres (320 feet approx.) in open field
: Total eight (8) tones available
: Total sixteen (16) possible channels
The unit comes from the factory on a pre-set radio frequency channel.
However, should you door chime activate intermittently for no reason at all,
it is possible that a similar unit is operating nearby on the same frequency.
The encoded frequency of the Converter (transmitter) and Door Chime
(receiver) can be changed to avoid this problem.
1. Remove the back of the case by pushing in the tab on the bottom with a small, flat screwdriver.
2. There is a 4 position dip switch marked 1,2,3,4. Use a small screwdriver to alter the dip switch levers to
the “On/Off” position, which can be altered to achieve a total sixteen (16) possible channels.
3. In any combination ensuring it is set to the same code on both Converter and Wireless Door Chime units.
4. Test to ensure correct operation before final installation.
Channel Selection
B+C SWITCH
A+C 8V/AC
B+C SWITCH
SX
Chime
unit
WIRED
CHIME
(Transformer
operation)
4
T
Converter
unit
SX
Chime
unit
WIRED
CHIME
(Transformer
operation)
3
T
Converter
unit
SX
Chime
unit
1
Converter
unit SX
Chime
unit
WIRED
CHIME
(Battery
operation)
2
Converter
unit
Please note that these diagrams are only for reference
as a guide.
EACH Wired chime can be wired differently, so if you
encounter problems, PLEASE CALL THE HELPLINE ON
0121 5449499
Wiring Installation
The Converter is designed to change your existing Wired Bell Push to wirefree.
1. Simply connect your Wired Bell Push with the cable from Converter to the terminals on your bellpush.
2. Your Wired Bell Push with Converter is ready to use.
B and C A and C A and C
A and C
Wired Bell
Push
Converter unit

Specyfikacje produktu

Marka: Elro
Kategoria: dzwonek do drzwi
Model: SX32 Deurbel

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Elro SX32 Deurbel, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje dzwonek do drzwi Elro

Elro

Elro DB260F Instrukcja

10 Października 2024
Elro

Elro DB3000 Instrukcja

29 Września 2024
Elro

Elro DB245 Instrukcja

29 Września 2024
Elro

Elro DB3000-P1C2W Instrukcja

29 Września 2024
Elro

Elro DV50-P1M2 Instrukcja

27 Września 2024
Elro

Elro DB100 Instrukcja

23 Września 2024
Elro

Elro DB202 Instrukcja

23 Września 2024
Elro

Elro DB101 Instrukcja

17 Września 2024
Elro

Elro MP001 Instrukcja

15 Września 2024
Elro

Elro DB350 Instrukcja

15 Września 2024

Instrukcje dzwonek do drzwi

Najnowsze instrukcje dla dzwonek do drzwi

Elektrobock

Elektrobock BZ33-MP3 Instrukcja

9 Stycznia 2025
Lorex

Lorex B861AJEB-E Instrukcja

8 Stycznia 2025
Ring

Ring Battery Doorbell Instrukcja

1 Stycznia 2025
Friedland

Friedland Evo D3200 Instrukcja

30 Grudnia 2025
Emos

Emos P5712 Instrukcja

29 Grudnia 2024
Vimar

Vimar ELVOX K40965 Instrukcja

29 Grudnia 2024
Heidemann

Heidemann 70370 Instrukcja

29 Grudnia 2024
Heidemann

Heidemann 70613 Instrukcja

29 Grudnia 2024
Heidemann

Heidemann 70215 Instrukcja

29 Grudnia 2024
Heidemann

Heidemann 70832 Instrukcja

29 Grudnia 2024