Instrukcja obsługi Elite Screens CineTension 2 TE100
Elite Screens
Ekran projekcyjny
CineTension 2 TE100
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Elite Screens CineTension 2 TE100 (6 stron) w kategorii Ekran projekcyjny. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/6
1
Rev.062916-DR www.elitescreens.com
Tab-tensioned Electric Motorized Projection Screen
CineTension 2 Series
User’s Guide
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedures below.
Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra
Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens.
Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this
unit are prohibited and will void your warranty. For more information, please contact our Technical
Support Department at (877) 511-1211 Ext. 604.
Please retain this user’s guide for future reference.
To avoid damaging the unit, do not use with any unauthorized accessories not recommended by
the manufacturer.
Handle the unit carefully during transportation to avoid any damages.
To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
The power outlet supplying power to the unit should be close to the unit and easily accessible.
Do not install the unit on uneven, inclined surfaces;
Do not install in damp places to avoid an electric shock or short circuit.
Do not place any heavy objects over the power cord.
Position the power cord properly to avoid creating a trip obstacle.
To avoid an electrical shock or fire, due to a loose contact or short circuit, do not overload the
power cord.
The internal & external parts of this unit are not end user serviceable. Do not attempt to
disassemble this unit by yourself. No one except authorized technicians can open and make
repairs to this unit.
Make sure the power source that this unit is connected to has a continuous power flow.
If there is need to use an extension cord, make sure the cord has an equal rating as the appliance
to avoid over heat.
Do not handle the power plug when your hands are wet or your feet are in contact with water.
Properly dispose of this equipment according to the environmental regulations in your area when
product is no longer of service.
2
Rev.062916-DR www.elitescreens.com
Do not use this unit under the following circumstances.
Disconnect the power cord under the conditions of heavy rain, wind thunder or lightning.
Avoid direct sun light, rain shower and moisture.
Keep away from fire sources and high temperature to prevent this device from overheating.
Cut off the power supply first before transportation or maintenance.
To avoid possible injury and/or an electric shock, do not attempt to use this screen if there is obvious
damage or if there are any evident broken parts.
Installation Warning
The instructions provided in this user’s guide are for reference only. Please consult a professional
installation company for further installation and safety advice. The installer must insure that
proper mounting hardware is used to provide adequate strength suitable for the installation. Elite
Screens is not liable for any faulty installations. For limit adjustment instructions, please contact
our Technical Support Department at (877) 511-1211 Ext. 604
The Screen’s is already set to its maximum drop distance. There is extra top black Top Black Drop NO
drop in the roller. Please be aware of this as it will void the limitation of your warranty.
Individual modifications to this product are prohibited and will void the warranty with the manufacturer.
Please contact Elite Screens Customer Service for any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures.
Reorient or relocate the receiving antenna of the device which may be casing the
interference.
Increase the separation between the screen and the device’s receiver.
Connect the equipment into a different power outlet other than the device.
Pre-Installation
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign
particles such as dust, sawdust, and/or liquids.
NOTE
Regardless of the mounting method, the screen should be securely supported so that the vibration or
pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure
the fasteners that are used are of adequate strength and suitable for the installation location.
Rev.062916-DR
3
-
way Wall
switch
CineTension 2 Series| Controls and Accessories
A. IR Remote
E. IR extended “eye” receiver
F. W
m
Screen operation
Electric Current:
Depending upon
1. After ensuring the power
outlet &
outlet.
2. Once the screen
has power, you’l
6 ways to control your
CineTension 2
1. (IR remote control
Item A, Fig 1
):
T
of sight contact with a beam range of 3
circular window located on the left sid
2. Item E, Fig 2IR “Eye” Receiver (
):
directly into the screen’s RJ-
45 input to
control option for your IR remote contr
installation.
3. Item BRF Remote Control ( ):
The
direct line of sight with a range of 100
4. 3-Way Wall Switch (
Item C, Fig
mount control box with an up/stop/dow
screen’s RJ-45 input.
Fi
3
CineTension 2 Series| Controls and Accessories
B. RF Remote C. Wall switch control box
D
Wireless 5
-12v (3.5 mm)
mono
trigger cable
G. AAA batteries
region, your Elite Screen will operate on 100v, 110
& screen are compatible (
voltage), plug
the power c
ll be able to control it using any of the 6 methods des
2
IR “Eye” Receiver
The Infrared functions by direct
line
30 feet. Aim the IR remote at the
e of the screen
The IR “Eye” Receiver plugs
o present a low pr
ofile line-of-sight
rol even in a
recessed ceiling
radio waves eliminate the need for a
feet.
3): The 3-way wall switch is a wall
wn button and plugs directly into the
ig.
3
www.elitescreens.com
D. 5
-12 volt trigger cable
H. Bubble leveler
v, or 220v voltage.
cord into the power
scribed below.
UP
STOP
DOWN
Fig.1
IR/RF remote
Fig.2
Specyfikacje produktu
| Marka: | Elite Screens |
| Kategoria: | Ekran projekcyjny |
| Model: | CineTension 2 TE100 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Elite Screens CineTension 2 TE100, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Ekran projekcyjny Elite Screens
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
Instrukcje Ekran projekcyjny
- Ekran projekcyjny Kodak
- Ekran projekcyjny Draper
- Ekran projekcyjny Pyle
- Ekran projekcyjny Oregon Scientific
- Ekran projekcyjny Optoma
- Ekran projekcyjny Duronic
- Ekran projekcyjny GPX
- Ekran projekcyjny Da-Lite
- Ekran projekcyjny AV:link
- Ekran projekcyjny Luxburg
- Ekran projekcyjny Elite
- Ekran projekcyjny EluneVision
- Ekran projekcyjny Celexon
- Ekran projekcyjny Lumene
- Ekran projekcyjny Stewart
- Ekran projekcyjny Avers
- Ekran projekcyjny Elite ProAV
- Ekran projekcyjny EPV
Najnowsze instrukcje dla Ekran projekcyjny
11 Października 2024
8 Października 2024
8 Października 2024
7 Października 2024
6 Października 2024
5 Października 2024
5 Października 2024
5 Października 2024
4 Października 2024
4 Października 2024