Instrukcja obsługi Eliminator Lighting Stealth Wash Zoom

Eliminator Lighting Niesklasyfikowane Stealth Wash Zoom

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Eliminator Lighting Stealth Wash Zoom (6 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
STEALTH WASH
ZOOM
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
Introduction:
The Stealth Wash Zoom is a unique DMX intelligent moving head unit. The Stealth Wash Zoom has
3 operating modes; sound active mode, show mode, or controlled via DMX controller. The Stealth
Wash Zoom has 2 DMX Channel modes; 5 or 16 channels. The unit can be run as a stand alone unit
or in a Master/Slave set up. This unit has been tested and there is no assembly required. Follow the
instructions on the following pages to operate your fixture. To enhance the beams effects you can
use a fog machine.
CAUTION! Please read and understand these instructions before installing or operating this unit.
SPECIFICATIONS:
Model: Stealth Wash Zoom
Supply Voltage: 100V-240V 50/60Hz
LED: 7 x 12W RGBW LED’s
Weight: 10lbs./ 4.5 kgs.
Size: 6.22” (L) x 9.4” (W) x 12.63” (H)
Fuse: 2 Amp
Power Consumption: 95W
Working Position: Any Safe position
Duty Cycle: None
DMX Channels: 2 DMX Channel Modes:
5 Channel Mode &
16 Channel Mode
Colors: RGBW
Warranty: 1 Year
CAUTION! Please read and
understand these instructions
before installing or operating
this unit.
Fuse Replacement: Locate and remove
the unit’s power cord. Once the cord
has been removed, the fuse holder is
located inside the power socket. Insert
a flat-head screw driver into the fuse
holder and gently pry out the holder.
Remove the bad fuse and replace with
a new one. The fuse holder has a built-in
second holder for a spare fuse.
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
AXXX: In this menu you can set the DMX address. Press the Up or Down buttons until “AXXX” is dis-
played. “XXX” is the current displayed DMX address. Press Enter and use the UP or Down buttons to
nd your desired address. When you have found your desired address press the Enter button to set
it.
CHNd: The Stealth Wash Zoom has 2 DMX channel modes; 5 channel mode and 16 channel mode.
In this menu you can select your desired channel mode. Press the Up or Down buttons until “CHNd” is dis-
played and press ENTER. Either “16CH” or “5CH” will be displayed. Use the Up and Down buttons
to toggle between the two modes and press Enter to make your selection and press Menu to exit.
SPNd (Sound Active Speed): In this menu you can adjust the sound active moving speed. Press
the Up or Down buttons until “SPNd” is displayed and press ENTER. Either “Low” (Low Speed) or
“High” (High Speed) will be displayed. Use the Up and Down buttons to toggle between the two
speeds and press Enter to make your selection. Press the Menu button to exit.
SLNd (Master/Slave): In this menu you can designate the xture as either a Master or Slave in a
master-slave set up. Press the Up or Down buttons until “SLNd” is displayed and press Enter. Either
“Mast” or “SL 1 will be displayed. Use the Up and Down buttons to nd your desired setting and
press Enter to make your selection. Press the Menu button to exit
SHNd (Show Mode): In this menu you can activate 1 of the 8 show mode’s. Press the Up or Down
buttons until “SHNd” is displayed and press Enter. 1 of 8 shows will be displayed. Use the Up and
Down buttons nd your desired show and press Enter to make your selection. Press the Menu button
to exit
Soun (Sound Active): In this menu you can activate Sound Active mode. Press the Up or Down buttons
until “Soun” is displayed and press Enter. Either “On” or “O” will be displayed. Use the Up and
Down buttons toggle between the choices and press Enter to make your selection. Press the Menu
button to exit.
PAn (Reverse Pan): In this menu you can reverse the Pan function. Press the Up or Down buttons
until “PAn” is displayed and press Enter. Press the Up or Downs buttons until “On” is displayed, and
press Enter. Press the Menu button to exit. This function works better when you have two units con-
nected in a Master/Slave setup. Have one unit set to reverse Pan and the other unit in normal Pan.
tIL ( Reverse Tilt): In this menu you can reverse the Tilt function. Press the Up or Down buttons until
“tIL” is displayed and press Enter. Press the Up or Downs buttons until “On” is displayed, and press
Enter. Press the Menu button to exit. This function works better when you have two units connected
in a Master/Slave setup. Have one unit set to reverse Tilt and the other unit in normal Tilt.
dISP (Display): In this menu you can “ip” the display 180°. Press the Up or Down buttons until
“dISP” is displayed and press Enter. Either “ON” or “OFF” will now be displayed. If you want to “ip”
the display press the Up button so that “ON” is displayed, and press Enter. Press the Menu button to
exit.
rFAC (Default Setting): In this menu you can reset the unit to it default settings. Press the Up or
Down buttons until “rFAC” is displayed and press Enter. Select “On” and press Enter to revert to
default settings. Press the Menu button to exit without any changes.
rSt (Reset): In this menu you can activate reset function. Press the Press the Up of Down buttons
until “rSt” is displayed and press Enter. The unit will now begin to reset. Press the Menu button to
exit.
OPERATION:
UNIVERSAL DMX CONTROL: This unit allows you to use any universal DMX- controller to control head 512
movement, LED colors, and the shutter (strobe). A DMX controller allows you to create unique programs tai-
lored to your individual needs. Follow the set-up specifications that are included with your DMX controller.
1. The Stealth Wash Zoom has two DMX channel modes; 5 DMX channels and 16 DMX channels.
2. Press the Up or Down buttons until “Chnd” is displayed, and press Enter.
3. Press the Up or Down buttons until your desired DMX channel mode is displayed, and press Enter.
4. Press the Mode button until “AXXX” is displayed. “XXX” is the current displayed DMX addess.
Press the Enter button.
4. Use the Up and Down buttons to find your desired address and press Enter.
5 Connect your DMX Controller and u. se the controller’s faders to control the various DMX fixture traits.
6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
7. For help operating in DMX mode consult the manual included with your DMX controller.
SOUND ACTIVE MODE:
1. To activate Sound Active mode, press the Up or Down buttons until “SOUN” is displayed, and press Enter.
2. Either “On” or “Off” will be displayed. To activate sound active mode press the Up or Down buttons until
“On” is displayed, and press Enter to select. Press the Menu button to exit
3. To adjust the movement speed in sound active mode press the Up or Down buttons until “SPnd” is
displayed. Either “HISP” (High Speed) or “LoSP” (Low Speed) will be displayed. Use the Up or Down
buttons to switch between the two modes and press Enter to make your selection. Press the Menu button
to exit.
SHOW MODE:
1. To activate Show mode, press the Up or Down buttons until “SHnd” is displayed, and press Enter.
2. 1 of 8 shows will be displayed. Use the Up or Down buttons to scroll through the shows and press Enter
to make your selection. Press the Menu button to exit.
MASTER-SLAVE SET UP: This function will allow you to link up to 16 units together and operate without a
controller. The units be sound active or in show mode In a Master-Slave set up one unit will act as the concan . -
trolling unit and the others will react to the controlling units programs. Any unit can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units together via the XLR connector on the rear of the
units. Remember the Male XLR connector is the input and the Female XLR connector is the output. The
rst unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the
male XLR connector only. For longer cable runs we suggest a terminator at the last fixture.
2. On the Master unit press the Menu button until “SLnd” is displayed, and press Enter. Use the UP and
DOWN buttons to scroll to the “Mast” setting and press Enter. Press the Menu button to exit.
3. After setting the Master unit to the master setting find and set your desired operating mode.
4. On the slave units press the Menu button until “SLnd” is displayed, and press ENTER. Press the Up or
Down buttons until “ ” and press Enter. Press the Menu button to exit.SL 1
5. The slave units will now follow the Master unit.
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
Ad t (OFFSET MENU) -
To enter the Oset Menu, press the Up or Down buttons until “Ad t” is displayed and press Enter. “P000” will
now be displayed. Press the Up button so that the display reads “P018” and press Enter. In this submenu you
are able to adjust the home positions of the pan and tilt motor’s, and focus motor. If you select delete, it will
reset all home positions to “0000”. Press the Menu button to exit.
Ad t:
(Delt) - Selecting this will default all oset values to “0000”.
(P) - Use the Up and Down buttons to adjust the oset of the Pan motor.
(t) - Use the Up and Down buttons to adjust the oset of the Tilt motor.
(F) - Use the Up and Down buttons to adjust the oset of the Focus motor.

Specyfikacje produktu

Marka: Eliminator Lighting
Kategoria: Niesklasyfikowane
Model: Stealth Wash Zoom

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Eliminator Lighting Stealth Wash Zoom, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Eliminator Lighting

Eliminator Lighting

Eliminator Lighting MDF3 Instrukcja

3 Października 2024
Eliminator Lighting

Eliminator Lighting MBMHD3 Instrukcja

2 Października 2024
Eliminator Lighting

Eliminator Lighting VF Volcano EP Instrukcja

2 Października 2024
Eliminator Lighting

Eliminator Lighting BUBBLETRON EXL GO Instrukcja

2 Października 2024
Eliminator Lighting

Eliminator Lighting Mega Bar RGBA EP Instrukcja

2 Października 2024
Eliminator Lighting

Eliminator Lighting Mega 64 Profile EP Instrukcja

30 Września 2024
Eliminator Lighting

Eliminator Lighting Mega Hex L Par Instrukcja

29 Września 2024
Eliminator Lighting

Eliminator Lighting EM30 Instrukcja

26 Września 2024
Eliminator Lighting

Eliminator Lighting HD-MB40 Instrukcja

26 Września 2024
Eliminator Lighting

Eliminator Lighting Aqua LED 2 Instrukcja

23 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024