Instrukcja obsługi Eliminator Lighting Follow Spot 100 LED

Eliminator Lighting Niesklasyfikowane Follow Spot 100 LED

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Eliminator Lighting Follow Spot 100 LED (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Follow Spot 100 LED
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
Introduction:
The Follow Spot 100 LED is a 2 channel DMX intelligent LED follow spot. The Follow Spot 100 LED features 8
colors, dimming capabilities, zoom, and focus. The Follow Spot 100 LED can be controlled via DMX control-
ler. The unit can be run as a stand alone unit or in a Master/Slave conguration. This unit has been tested and
there is no assembly required. The unit is ready to be plugged in to a power outlet. To enhance the beams
effects you can use a fog machine.
CAUTION! Please read and understand these instructions before installing or operating this unit.
SPECIFICATIONS:
Model: Follow Spot 100 LED
LED: 70W LED
Weight: 15lbs./ 7kgs.
Size: 580 x 280 x 280mm
Beam Angle: 16 - 22 Degrees
Fuse: 5 Amp
Supply Voltage: 100-240V 60-50Hz
Power Consumption: 100W
Working Position: Any Safe position
Duty Cycle: None
DMX Channels: 2 DMX Channels
Warranty: 1 Year
CAUTION! Please read and understand these
instructions before installing or operating this unit.
1 Year Limited Warranty: Eliminator Lighting warranty is valid from the date of purchase. Our
1 year limited warranty covers manufacturing defects only. Serial number, place of purchase with
dated valid receipt must be submitted at time of service. Eliminator Lighting warranty does not cover
items or parts prone to wear and tear: motors, fuses, brushes and belts. Eliminator Lighting warranty
is only valid with-in the United States.
Fuse Replacement: Uplug the unit from its
power source. Using a phillips-head screw driver
unscrew and remove the fuse housing. Remove
the bad fuse and replace with a new one.
DMX TRAITS: 2 CHANNELS
CHANNEL 1: COLORS
0 - 31 = OPEN (WHITE)
32 - 63 = RED
33 - 95 = YELLOW
96 - 127 = BLUE
128 - 159 = GREEN
160 - 191 = PURPLE
192 - 223= ORANGE
224 - 255 = PINK
CHANNEL 2: MASTER DIMMER
0 - 255 = 0%-100%
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
OPERATION:
DMX Mode:
Operating through a DMX controller give the user the freedom to create own programs tailored to their s their
own individual needs. This unction also allows you to use your xtures as spot lights. The Follow Spot 100 f
LED has 2 DMX channels. See the front page for the DMX traits.
1. This function will allow you to control each individual xture’s traits with a standard DMX 512 controller.
2. Plug in the xture via the XLR connections to any standard DMX controller.
3. Press the function select button to activate DMX mode. The DMX LED and the DMX Receive LED should
glow when in DMX mode and the unit is receiving a signal.
Master-Slave Conguration:
This function will allow you to link units together to run in a Master-Slave mode. In Master-Slave operation s
one unit will act as the controlling unit and the others will react to the controlling units built-in programs. Any
unit can act as a Master or as a Slave however, only one unit can be programmed to act as the “Master.”
1. Daisy chain your units via the XLR connector on the rear of the unit. Use standard XLR microphone cables
to link your units together. Remember that the Male XLR connector is the input and the Female XLR con
nector is the output. The rst unit in the chain (master) will use the female XLR connector only. The last
unit in the chain will use the male XLR connector only.
2. Using the Master unit, choose your desired operating mode and connect the “Slave” unit or units.
1 32
456
Functions:
1. Dimmer Buttons - Used to adjust intensity. - Blackout or open the shutter2. Shutter
3. DMX Address/Status LED’s - Shows the current DMX address, and xture status. LED’s show
the xtures current operating status: DMX LED, DMX Receiving LED, or Manual mode LED.
4. DMX Address Adjustment Buttons - Use these buttons to change the DMX Address.
5. Function Selection Button - Use this button to switch between DMX Mode and Manual Mode.
6. Color Buttons - Choose from 7 different colors plus white.

Specyfikacje produktu

Marka: Eliminator Lighting
Kategoria: Niesklasyfikowane
Model: Follow Spot 100 LED

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Eliminator Lighting Follow Spot 100 LED, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Eliminator Lighting

Eliminator Lighting

Eliminator Lighting MDF3 Instrukcja

3 Października 2024
Eliminator Lighting

Eliminator Lighting MBMHD3 Instrukcja

2 Października 2024
Eliminator Lighting

Eliminator Lighting VF Volcano EP Instrukcja

2 Października 2024
Eliminator Lighting

Eliminator Lighting BUBBLETRON EXL GO Instrukcja

2 Października 2024
Eliminator Lighting

Eliminator Lighting Mega Bar RGBA EP Instrukcja

2 Października 2024
Eliminator Lighting

Eliminator Lighting Mega 64 Profile EP Instrukcja

30 Września 2024
Eliminator Lighting

Eliminator Lighting Mega Hex L Par Instrukcja

29 Września 2024
Eliminator Lighting

Eliminator Lighting EM30 Instrukcja

26 Września 2024
Eliminator Lighting

Eliminator Lighting HD-MB40 Instrukcja

26 Września 2024
Eliminator Lighting

Eliminator Lighting Aqua LED 2 Instrukcja

23 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024