Instrukcja obsługi Electro Harmonix V256 Vocoder

Electro Harmonix Niesklasyfikowane V256 Vocoder

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electro Harmonix V256 Vocoder (16 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/16
1
V256
Vocoder
Congratulations on your purchase of the Electro-Harmonix V256 Vocoder The V256 is a .
versatile and easy to use vocoder with the added benefit of being in a compact pedal format.
Musicians no longer need large rack equipment, computer plugins, or large keyboards to get
a wide array of classic and modern vocoder sounds as well as a few very unique vocal
transposition effects. The V256 includes internal synthesizers for easy vocoding without an
external instrument.
Special Features of th V256: e
3 VOX-ROBO vocoder modes that feature a robotic synthesizer
Single, Major, and Minor modes feature a drone synthesizer
3 Brand new vocal transposition modes including TRANSPOSITION INSTRUMENT CTRL, and ,
REFLEX-TUNE
Vocoder bands adjustable from a vintage sounding 8 bands to a smooth sounding 256 bands
TONE GENDER BENDER, and PITCH controls ,
Save and load up to 9 presets: 1 preset for each mode.
Scroll through the presets using the MODE knob or PRESET footswitch.
Built-In balanced Mic Pre-Amp with switchable Phantom Power and Gain adjustment.
Effect output on balanced XLR line output and 1/4” unbalanced instrument output
WARNING: Use only the AC Adapter that the V256 comes supplied
with Do not use any other AC Adapters. Using other AC adapters, .
even those made by Electro-Harmonix, could cause harm to the unit,
the adapter or you. The V256 does not use batteries.
2
- QUICK START GUIDE -
BASIC MIXER CONNECTION SETUP
1. Connect your microphone to the MIC input on the right side of the V256 using a
balanced XLR cable .
2. Using an unbalanced instrument cable, plug your instrument into the INST Input Jack on
the right side of the V256.
3. Connect a balanced XLR cable to the EFFECT output jack on the left side of the V256.
Connect the other end of the XLR cable to the line input of a mixer.
4. Connect an unbalanced instrument cable from the INST output jack on the left side of
the V256 Connect the other end of the instrument cable to the instrument input of a .
mixer, or the input of an amplifier.
5. Plug the AC Adapter into a wall outlet.
6. Plug the barrel connector of the AC Adapter into the 9V power jack at the top of the
V256.
Polarity is center negative
.
7. If using a condenser microphone, flip the Phantom Power switch up to the top position,
otherwise leave it off. The Phantom Power switch is located on the right side of the
V256, next to the XLR M input. IC
8. Push the M BYPASS footswitch until its associated LED is OFF. Sing into the IC
microphone, you will hear your dry vocal at this point. Adjust mixer settings as well as
the MIC GAIN switch on the V256 to obtain optimal mic levels.
BASIC AMPLIFIER CONNECTION SETUP
1. Connect your microphone to the MIC input on the right side of the V256 using a
balanced XLR cable.
2. Using an unbalanced instrument cable, plug your instrument into the INST Input Jack on
the right side of the V256.
3. Connect an unbalanced instrument cable from the INST output jack on the left side of
the V256. Connect the other end of the instrument cable to the input of a guitar, bass,
or keyboard amplifier.
4. Plug the AC Adapter into a wall outlet.
5. Plug the barrel connector of the AC Adapter into the 9V power jack at the top of the
V256.
Polarity is center negative
.
6. If using a condenser microphone, flip the Phantom Power switch up to the top position,
otherwise leave it off. The Phantom Power switch is located on the right side of the
V256, next to the XLR MIC input.
7. Push the MIC BYPASS footswitch until its associated LED is OFF. Play the instrument,
you will hear only dry instrument signal at this point.
3
8. The factory setting for the INST output of the V256 is 100% dry instrument signal only.
In order to use the V256 in this mode the INST output blend needs to be adjusted.
9. Hold down the MIC BYPASS footswitch and adjust the BLEND knob. Fully CCW is 100%
instrument signal. As you turn the knob CW more V256 effect signal is added and at
noon, the mix of dry instrument to V256 effect will be even. As you continue to turn the
knob CW past noon, the dry instrument level will decrease and at fully CW the mix will
be 100% V256 effect.
10. After the BLEND knob is adjusted for the desired mix, release the MIC BYPASS
footswitch and the instrument output mix will be set. the MIC BYPASS is not held If
down, moving the blend knob will make no difference to the INST output mix.
BASIC VOCODER SETTINGS
1. Now that the V256 is hooked up and ready to go, here is a sample setting to get started.
2. Turn the MODE knob until the mode VOX-ROBO 1 is selected and set the other
parameters as follows:
-BLEND FULLY CW
-BANDS NOON
-TONE NOON
-GENDER NOON
-PITCH FULLY CW
3. Press and release the MIC BYPASS footswitch so that the effect is now ON and the LED
is lit.
4. Play the instrument and sing into the microphone at the same time. You will now hear
your voice modulating the sound of the carrier instrument.
5. To use the internal synthesizer, turn the PITCH knob to noon.
6. Sing into the microphone and you will hear your voice modulate the robotic synth.
7. These basic settings also apply to the single, major, and minor drone modes.
BASIC VOCAL TRANSPOSITION SETTINGS
1. Turn the MODE knob until the mode TRANSPOSITION is selected and set the other
parameters as follows:
-BLEND FULLY CW
-BANDS NOON
-TONE NOON
-GENDER NOON
-PITCH NOON
2. In this setting the vocal transposition will be at unity. Using the XLR output, turn BLEND
to noon for a subtle double tracking effect.
3. Adjust the GENDER BENDER knob to hear a more male or female version of your voice.
4. Turn the PITCH knob fully CW to hear 1 octave up, and fully CCW to hear 1 octave
down.

Specyfikacje produktu

Marka: Electro Harmonix
Kategoria: Niesklasyfikowane
Model: V256 Vocoder

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Electro Harmonix V256 Vocoder, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Electro Harmonix

Electro Harmonix

Electro Harmonix Cock Fight Instrukcja

7 Października 2024
Electro Harmonix

Electro Harmonix Cock Fight Plus Instrukcja

7 Października 2024
Electro Harmonix

Electro Harmonix Holy Grail Max Instrukcja

7 Października 2024
Electro Harmonix

Electro Harmonix Spruce Goose Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix Germanium 4 Big Muff Pi Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix LPB-3 Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix Deluxe Memory Man 550-TT Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix 2X12 Speaker Cabinet Instrukcja

3 Października 2024
Electro Harmonix

Electro Harmonix Rerun Instrukcja

3 Października 2024
Electro Harmonix

Electro Harmonix 15Watt Instrukcja

30 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024