Instrukcja obsługi Electro Harmonix Slap-Back Echo


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electro Harmonix Slap-Back Echo (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/4
Congratulations on your purchase of the Slap-Back Echo delay pedal! The Slap-Back
Echo is a modern day update of the rare and classic Electro-Harmonix Slap-
Back Echo from 1978. A Gain knob, Blend knob, and Time switch allow you to
tailor the Slap-Backs all-analog echo to enhance your tone from subtle
doubling to intense bathtub reections. The compact size allows it to easily
squeeze onto crowded pedalboards.
Analog Echo
POWER SUPPY REQUIREMENTS:
Voltage: 9VDC Current: 15mA Center-Negative Polarity:
This device comes equipped with an Electro-Harmonix 9.6DC-200 power supply. Use of the wrong adapter
or a plug with the wrong polarity may damage the device and void the warranty. Do not exceed 10.5VDC
on the power plug. Power supplies rated for less than 25mA can cause the device to act unreliably
- 2 -
Controls and Connections
1. GAIN Knob The GAIN knob boosts your dry signal before it hits the
BLEND knob and echo circuitry. As you turn GAIN clockwise, your signal
gets louder. The GAIN knob increases your signal level by up to 20dB,
which is handy for added volume during solos and important riffs.
2. BLEND Knob The BLEND knob controls the wet/dry mix at the
output jack. With the knob fully counterclockwise, the signal is 100%
dry. Set the knob fully clockwise and your output is all echo. Please
note: the dry and wet signals are both boosted by the GAIN knob.
The output signal is boosted even with BLEND set to 100% dry.
3. TIME Switch The TIME switch allows you to select between three
different delay times:
UP: 100ms
MIDDLE: 65ms
DOWN: 45ms
4. FOOTSWITCH and STATUS LED The footswitch engages or bypasses
the effect. The Status LED lights when the effect is engaged. The LED
is off in bypass mode. The Slap-Back Echo employs True Bypass.
5. INPUT Jack Audio input to the Slap-Back Echo.
6. AMP Jack Audio output from the Slap-Back Echo. In bypass mode,
the AMP jack is directly connected to the INPUT jack and nothing else.
7. 9V Power Jack Attach the output plug from the included power
supply to the 9V power jack. The Slap-Back Echo draws 15mA at 9VDC
on a center-negative plug. Do not exceed 10.5VDC on the power jack.
Operating Instructions
Connect your guitar to the INPUT jack on the Slap-Back Echo and the
AMP jack to your amp’s input. Plug in the included power supply and
insert its output plug into the power jack. Press the footswitch to
ensure the Status LED is lit. Your Slap-Back Echo is now ready to go.
For a quick starter setting, set the controls to the following:
GAIN: BLEND: 9 o’clock 11 o’clock
TIME: Upper position
- 3 -
Notes and Specications
t Audio input impedance at INPUT jack: 220KΩ
t Audio output impedance at OUTPUT jack: 7KΩ
t Current draw: 15mA
t Power Supply: 9VDC, Center-negative polarity


Specyfikacje produktu

Marka: Electro Harmonix
Kategoria: Niesklasyfikowane
Model: Slap-Back Echo

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Electro Harmonix Slap-Back Echo, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Electro Harmonix

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024