Instrukcja obsługi Electro Harmonix Ring Thing

Electro Harmonix Niesklasyfikowane Ring Thing

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electro Harmonix Ring Thing (16 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/16

RING THING

Single Sideband Modulator

Congratulations on your purchase of the Electro-Harmonix Ring Thing. The Ring Thing has

four selectable modes that utilize either frequency or pitch shift modulation: Ring

Modulation, Single Sideband Upper Band, Single Sideband Lower Band and Pitch Shift. – –

The Ring Modulator section builds upon the original EHX Frequency Analyzer adding to it

selectable carrier waveforms, a sweepable filter, presets and expression pedal control.

Single-sideband modulation is a new effect based on Ring Modulation but where only one

band is present, making it a more harmonious effect. Finally, we have a powerful

modulatable pitch shifter that can do detune effects, vibrato, chorus, transpose or even

whammy when you use an external expression pedal.

Special Features of the Ring Thing:



Four selectable modes: Ring Modulation (RM), Upper Band Modulation (UB),

Lower Band Modulation (LB), Pitch Shift (PS).



Single Sideband frequency shifter with separate simultaneous upper

and lower sideband outputs.



Automatically tune the Ring Modulator to any incoming signal by

pressing and holding the PRESET FSW.



The Ring and SSB Modulators can automatically tune to a note you play on your

instrument



Pitch shifter with range of +/- 2 octaves.



Five modulation waveforms: Square, Sine, Ramp up/down, Triangle.



Expression Pedal control over carrier frequency or pitch shift amount.



Optional external oscillator/modulation input.



Mono Input / Stereo Output in all modes.



Save and load up to 9 presets.

WARNING:

The Ring Thing comes equipped with an Electro-Harmonix 9.6DC-200BI

power supply (same as used by Boss™ & Ibanez™: 9.6 Volts DC 200mA). The Ring

Thing requires 190mA at 9VDC with a plug that is center negative. Using the wrong AC

adapter, even those made by Electro-Harmonix, could cause harm to the unit, the

adapter or you. The Ring Thing does not use batteries.

- Quick Start Guide -

BASIC AMPLIFIER CONNECTION SETUP

1. Using an unbalanced instrument cable, plug the output of your instrument into

the INST Input Jack on the right side of the Ring Thing .

2. Connect an unbalanced instrument cable from the MONO L output jack on the

left side of the Ring Thing. Connect the other end of the instrument cable to the

input of a guitar, bass, or keyboard amplifier.

3. Plug the AC Adapter into a wall outlet.

4. Plug the barrel connector of the AC Adapter into the 9V power jack at the top of

the Ring Thing.

Polarity is center negative

5. Apply power to the amplifier.

BASIC SETTINGS FOR RING MODULATOR MODE

–

This mode brings back all the

sounds of the Frequency Analyzer, with a few extras.

1. Connect the Ring Thing as described in Basic Amplifier Connection Setup.

2. Press the BYPASS footswitch so the STATUS LED is on

3. Press the MODE knob so that the Left LED is lit: RM.

4. Turn the following knobs to 50% or 12 o’clock: BLEND, WAVE, FINE/DEPTH, and

COARSE.

5. Turn the FILTER/RATE knob fully clockwise.

6. If an expression pedal is plugged in set it to the toe down position.

7. To change the modulation frequency, turn the FINE and/or COARSE knobs.

Automatically Tune the Ring Modulator –

Play a single note on your

instrument and then press and hold the PRESET/TUNE footswitch for 1 second. The

Ring Thing will automatically tune its internal modulator to the note you are playing.

This function is monophonic, it is designed to search for the fundamental pitch rather

than figure out what chord is being played. The PRESET/TUNE footswitch can be held

down to continuously tune the ring modulator to the input signal.

The WAVE Function –

the WAVE knob sets the waveform of the Ring Modulator

in RM and PS modes. Starting from full counter-clockwise, the choices are: SQUARE,

SINE, RAMP DOWN, RAMP UP, and TRIANGLE. Try turning the knob as you play, you

will notice some waveforms produce more harmonics than others. Additionally you

can crossfade from SQUARE to SINE to RAMP DOWN, then it switches to RAMP UP

and TRIANGLE.

Using an External Oscillator -

To use an external oscillator, as the RM’s carrier,

plug the output of another instrument, recording or mic pre into the MOD input jack

and turn the WAVE knob fully counter-clockwise. The signal at the MOD input jack

will override the Ring Thing’s internal modulator. In RM, UB and LB modes, the

external oscillator will become the effect’s carrier signal. In PS mode, the external

oscillator will modulate the effect’s pitch shift amount.

Using an Expression Pedal –

Plug an expression pedal into the EXP ¼” Jack

and set the FINE knob to full counter-clockwise to control the Modulation Frequency.

The COARSE knob sets the range at the toe-down position.

Using the Filter –

In RM mode, the FILTER/RATE knob control the cutoff

frequency of the low pass filter, allowing you to adjust the tone or harmonic richness

of the ring mod effect. As you turn the knob clockwise, the tone becomes brighter.

Using Ring Modulation as Tremolo –

In RM mode, if you turn up the BLEND

knob to the full clockwise position, and turn the COARSE knob down below 9 o’clock,

the Ring Thing will act like a tremolo effect. Use the WAVE knob to change the shape

of the tremolo. Use the FINE knob to fine tune the rate.

Troubleshooting –

Not hearing the Ring Modulator or just something unexpected?

Check to make sure that the BLEND knob is 50% or higher and that the FILTER/RATE

knob is not turned to full counter-clockwise.

BASIC SETTINGS FOR LOWER/UPPER SIDEBAND MODE

–

UB and LB modes split

up the ring modulator signal into its respective sideband components. Each sideband is

sent to either the MONO/L or R output jacks, where the selected mode is always sent to

the Left/Mono output. For example, in UB mode, the upper band is output from the

MONO/L output and the lower band is sent out the R output.

1. Connect the Ring Thing as described in Basic Amplifier Connection Setup.

2. Press the BYPASS footswitch so the STATUS LED is on

3. Press the MODE knob so that the Center LED is lit for UB or the Right LED for LB.

4. Turn the fol , FINE/DEPTH, and lowing knobs to 50% or 12 o’clock: BLEND, WAVE

COARSE.

5. Turn the FILTER/RATE knob fully clockwise.

6. If an expression pedal is plugged in set it to the toe down position.

7. To change the modulation frequency, turn the FINE and/or COARSE knobs.

Automatically tune the Single Sideband Modulators –

Play a single note

on your instrument and then press and hold the PRESET/TUNE footswitch for 1

second. The Ring Thing will automatically tune its internal modulator to the note you

are playing. This function is monophonic, it is designed to search for the fundamental

pitch rather than figure out what chord is being played. The PRESET/TUNE footswitch

can be held down to continuously tune the ring modulator to the input signal.

Specyfikacje produktu

Marka:	Electro Harmonix
Kategoria:	Niesklasyfikowane
Model:	Ring Thing

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Electro Harmonix Ring Thing, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Electro Harmonix

Electro Harmonix Cock Fight Instrukcja

7 Października 2024

Electro Harmonix Cock Fight Plus Instrukcja

7 Października 2024

Electro Harmonix Holy Grail Max Instrukcja

7 Października 2024

Electro Harmonix Spruce Goose Instrukcja

5 Października 2024

Electro Harmonix Germanium 4 Big Muff Pi Instrukcja

5 Października 2024

Electro Harmonix LPB-3 Instrukcja

5 Października 2024

Electro Harmonix Deluxe Memory Man 550-TT Instrukcja

5 Października 2024

Electro Harmonix 2X12 Speaker Cabinet Instrukcja

3 Października 2024

Electro Harmonix Rerun Instrukcja

3 Października 2024

Electro Harmonix 15Watt Instrukcja

30 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024