Instrukcja obsługi Electro Harmonix Riddle

Electro Harmonix Niesklasyfikowane Riddle

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electro Harmonix Riddle (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
RIDDLE: Q BALLS
FOR GUITAR
Congratulations on your purchase of the Riddle: Q-Balls envelope
controlled filter for guitar! This is a very powerful tool for musical
expression that opens a new horizon of sonic potential for your
guitar. Please take a few minutes to familiarize yourself with the
Riddle . ’s controls and how they work
Envelope controlled filters are a unique type of sound modifier
where the intensity of the effect is controlled by the user’s playing
dynamics. The volume and dynamic of the incoming audio signal is
used to control a swept filter. As the volume increases or decreases
so does the frequency of the filter.
With 3 selectable filter modes, along with START, STOP, ATTACK,
DECAY, Q and SENSITIVITY controls, all of the classic Q sounds are
available to the user. Also, many new sounds and vivid textures
can be achieved like never before. A new analog distortion circuit
was created specifically for the RIDDLE, and adds a dynamic edge
to the filters sound. With the addition of an expression pedal input
(expression pedal not included), the RIDDLE provides manual
control of the filter sweep.
— — POWER
WARNING:
Use only the
US96DC-200Bl AC Adapter that the RIDDLE comes
supplied with.
Do not use any other AC Adapters. Using other AC adapters,
even those made by Electro-Harmonix, could cause harm to the unit, the
adapter or you. The RIDDLE does not use batteries.
— — CONTROLS
BLEND –Controls the output mix of the dry and eected signal. Fully CCW is
100% dry with no eect added. Fully CW is 100% wet with no remaining dry
signal.
MODE –This is a rotary switch used to select between the 3 lter modes available
on the RIDDLE. Select between LP (low pass), BP (band pass), and HP (high pass)
modes to emphasize a dierent frequency band. Selecting between these modes
does not change the start and stop frequencies.
ATTACK –This knob controls how quickly the lter will sweep from the frequency
set by the “START” knob to the frequency set by the “STOP” knob. Fully CCW
will have the fastest attack setting and is good for quick percussive styles of playing.
Fully CW will have the slowest attack setting and creates a slower smoother sweep
for a bowed sound.
DECAY –This knob controls how sensitive the reset circuit is when falling back
from the “STOP” setting to the “START” setting. Fully CCW will have the most
sensitive reset. In this setting the sweep will reset the fastest and the easiest. Use
this when playing quick staccato notes to make sure every note triggers a new
envelope sweep. Fully CW will maximize the decay setting. Use a longer decay
setting when you don’t want every note to reset.
START –This knob sets the frequency that the sweep starts at. Fully CCW is the
lowest frequency (about 40Hz). Fully CW is the highest setting (about 3Khz). Use
this knob along with the “STOP” knob to set the range and direction of the sweep.
For example, a low “START” and a high “STOP” will sweep upward. A high
“START” and a low “STOP” will sweep downward.
STOP –This knob sets the frequency that the filter sweeps to. Fully CCW is the
lowest setting (about Hz). Fully CW is the highest setting (about 5KHz).80
Q –This knob controls the resonance of the Q. Fully CCW is the widest bandwidth
and fully CW is the most resonant for a more dramatic eect.
SENSITIVITY –This knob controls the input sensitivity of the envelope lter
circuit. Fully CCW is the least sensitive, and the circuit will be less reactive to the
instrument input. Fully CW is the most sensitive and the circuit will be the most
reactive to the instrument input.
A NOTE ON INTERACTIVE CONTROLS:
The “ATTACK”, “DECAY”, “START”, “STOP” and “SENSITIVITY” knob are
highly interactive. If Attack is set to slow, the Decay is set to fast, or the Sensitivity
is set to low, the lter sweep may not reach the stop frequency. The lowest
frequency sweeps in the RIDDLE can be dicult to hear. If this causes the attack to
sound abrupt, tune the start position so the sweep begins at a more audible
frequency. All of the functions depend heavily on how the Sensitivity. Take some
time to become familiar with these knobs and functions and learn how they work
together to eect dierent styles of playing.
DISTORTION FOOTSWITCH/STATUS LED This footswitch engages the –
analog distortion circuitry in the RIDDLE When distortion is engaged, the LED .
will turn on, and when distortion is disengaged the LED will turn o. The intensity
of the distortion is controlled by the “SENSITIVITY” knob. Inside the pedal there is
a Trim Pot labeled “ ”DISTORTION LEVEL . This can be adjusted by the user to
ne tune the volume of the distortion when engaged. This will not aect the gain or
intensity of the distortion. adjust any other trim pot on the board as they DO NOT
have been carefully calibrated for optimum performance.
EXPRESSION PEDAL INPUT –An optional expression pedal can be used with
the RIDDLE for manual control of the lter. When the pedal is in toe up position,
the frequency will be at the “START” position. In the toe down position, the
frequency will be at the “STOP” position. Use this along with various “Q” knob
setting to get resonant lter sweeps as well as wah-wah sounds with versatile a
range.
BYPASS FOOTSWITCH/STATUS LED The footswitch engages/disengages the –
eect. If the eect is engaged, the LED will light up. When the eect is disengaged,
the LED will turn o, and the pedal will be in true bypass.
INPUT Jack – Connect your instrument’s output to this ¼” mono jack. The input
impedance presented at this jack is 710Kohms
EFFECT OUT Jack –Connect this ¼” mono jack to your amplifier’s input. The
output impedance presented at this jack is ohms. 300
DIRECT OUT Jack –This is a direct out signal from the input. This signal does
not go though any of the eects circuitry.
CAUTION: This pedal was designed to give the user the maximum potential for
user customizability and there are some setting combinations that are extreme. If the
Q setting is maxed, at the peak high and low frequency this pedal can be
INCREDIBLY loud.

Specyfikacje produktu

Marka: Electro Harmonix
Kategoria: Niesklasyfikowane
Model: Riddle

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Electro Harmonix Riddle, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Electro Harmonix

Electro Harmonix

Electro Harmonix Cock Fight Instrukcja

7 Października 2024
Electro Harmonix

Electro Harmonix Cock Fight Plus Instrukcja

7 Października 2024
Electro Harmonix

Electro Harmonix Holy Grail Max Instrukcja

7 Października 2024
Electro Harmonix

Electro Harmonix Spruce Goose Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix Germanium 4 Big Muff Pi Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix LPB-3 Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix Deluxe Memory Man 550-TT Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix 2X12 Speaker Cabinet Instrukcja

3 Października 2024
Electro Harmonix

Electro Harmonix Rerun Instrukcja

3 Października 2024
Electro Harmonix

Electro Harmonix 15Watt Instrukcja

30 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024