Instrukcja obsługi Electro Harmonix Rerun


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electro Harmonix Rerun (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/4
RERUN
User Manual
Tape Delay
Welcome to the Electro-Harmonix Rerun Tape Delay:
an extremely compact tape delay modeler with up
to 3 seconds of delay time. The Rerun lets you dial
in repeats with saturation and flutter for lush, organic
delay tones. The pedal features tap-tempo, to keep
the echoes in time with your music, tails mode, to
keep the repeats going after switching to bypass,
and foot accessible maximum feedback for run-
away self-oscillation.
Operating Instructions
Insert the output plug from the supplied 9VDC AC
adapter into the power jack at the top of the Rerun.
The unit must be powered to pass signal, even in
bypass. The Rerun features buffered analog bypass
or digital bypass depending on settings. Connect
an instrument cable from your instrument to the
Input jack. Connect an instrument cable between
the Output jack and a suitable amplifier. Click the
footswitch to engage the pedal and light the LED.
BLEND DELAY
FLUTTER
SAT FDBK
8
9
1 2
5
6
6
3 4
7
Power Suppy Requirements: Voltage: 9VDC Current: 100mA Polarity: Center-Negative
This device comes equipped with an Electro-Harmonix 9.6DC-200 power supply. Use of the wrong adapter or a
plug with the wrong polarity may damage the device and void the warranty. Do not exceed 10.5VDC on the power
plug. Power supplies rated for less than 100mA may cause the device to act unreliably.
Controls & Jacks
1. BLEND Adjusts the output mix from 100% dry
to 100% wet.
2. DELAY Controls the delay time, ranging from
8ms to 3s.
3. SAT Controls the saturation, or distortion, on
the echo repeats.
4. FDBK Controls the number of echo repeats
the Rerun generates. At minimum you get one
repeat, at maximum you get runaway self-os-
cillation.
5. FLUTTER Button Flutter emulates the pitch
modulation that occurs on old, worn-down tape
machines. Press this button to set flutter depth:
Green – LOW FLUTTER
Orange – MEDIUM FLUTTER
Red – HIGH FLUTTER
6. Footswitch and Status LED The footswitch
engages or bypasses the effect. The LED indi-
cates the selected Flutter depth. In bypass
mode, the LED is off. The LED blinks at the lat-
est tap reading when the delay time is set by
tap tempo.
7. Input Jack Impedance: 2.2MΩ, Max In: +1.5 dBu
8. Output Jack Impedance: 680Ω, Max Out: +2.1 dBu
9. Power Jack Current draw: 100mA at 9.0VDC
Tap Tempo
The footswitch can be used to set the delay
time. Press and release the footswitch at least
twice, in time with your music, to set the tempo.
The LED blinks at the tempo to confirm the
delay time is set by tap-tempo. To turn off
tap-tempo, simply turn the DELAY knob to reset
the delay time. You can completely disable
tap-tempo by following these steps:
1. Power down the Rerun.
2. Press and hold the footswitch while reapply-
ing power.
3. Continue to hold the footswitch for about
two seconds; the LED will slowly blink
through all three colors twice.
4. Release the footswitch; tap-tempo is now
disabled.
5. Repeat this process to re-enable tap-tempo.
Tap-tempo disable is recalled through power
cycles so you can set it and forget it.


Specyfikacje produktu

Marka: Electro Harmonix
Kategoria: Niesklasyfikowane
Model: Rerun

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Electro Harmonix Rerun, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Electro Harmonix

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024