Instrukcja obsługi Electro Harmonix Next Step Slammi

Electro Harmonix Niesklasyfikowane Next Step Slammi

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electro Harmonix Next Step Slammi (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
SLAMMI
POLYPHONIC PITCH-SHIFT /HARMONY PEDAL ER
Congratulations on your purchase of the Electro-Harmonix , foot controlled Slammi a
polyphonic pitch-shifter/harmony pedal. The smoothly sweeps the pitch of Slammi
the guitar signal either up or down without using any moving parts, it does not use a
potentiometer, optics or magnetism. The result is a responsive pedal that allows
precise control over a clean, glitch free, polyphonic pitch-shifting algorithm. To top it
off the can create harmonized intervals by mixing your dry signal with the Slammi
effect using the adjustable DRY VOL control.
GETTING STARTED
Plug your guitar into the INPUT jack; connect your amp to the OUTPUT jack Tilt the .
Slammi forward to light the EHX logo in the center of the pedal. Your Slammi is ready
to go! as long as a plug is inserted into the P jack, a drain is Please note: IN UT
placed on the 9V battery inside the Slammi. It is recommended that you disconnect
the INPUT jack when the Slammi is not in use to extend battery life.
MAX BEND Control
The Max Bend control, located on the input side of the Slammi, acts as an 11-way
switch selecting the maximum bend or maximum interval of chromatic transposition.
The chart below shows where each maximum bend setting is located on the
thumbwheel, the odd numbers are not actually on the control:
0
1
2
3
4
5
6
8
9
10
Detune
½
Step
Major
2nd
Major
3rd
Perfect
4th
Perfect
5th
Major
6th
1
Oct
2
Oct
3
Oct/
Dive
BEND Push Button
The Bend button, next to the MAX BEND thumbwheel, selects whether the pitch is
shifted up or down relative to the original pitch. If the button is , the pitch will be out
shifted ; likewise if the button is , the pitch is shifted . UP in DOWN DRY VOL Control
The Dry Volume (DRY VOL) thumbwheel, xt to the INPUT jack, controls the volume ne
of your dry signal, mixing it with the effect signal. This enables you to harmonize with
your original pitch while at a fixed interval or when you bend notes. A detuned effect
can be made when MAX BEND is set to 0 and DRY VOL is above 0.
CALIBRATION
To ensure the Slammi responds to its full sweep range, it may be necessary to
calibrate the sweep of the Slammi when it is used on a different surface since its last
use. It is particularly important to calibrate if the Slammi is used on a slanted surface.
We recommend calibrating the Slammi after unwrapping it from its packaging, during
your first use of the pedal. Slammi is unique compared to other Next Step The
pedals in that it can be calibrated so maximum effect is either in the toe-down
position or heel-down position, allowing you to reverse the pedal sweep direction. ’s
CALIBRATION PROCEDURE TOE POSITION = MAX BEND (factory default) –
1. Place the pedal on the surface where it will be used.
2. Ensure the Slammi pedal is sitting flat on the surface then press and release
the CALIBRATE button once; the EHX logo begins to blink indicating the toe
position has been saved.
3. While the EHX logo continues to blink, rock the pedal all the way back to the
extreme heel position and hold it there.
4. Press and release the CALIBRATE button once more.
5. The EHX logo will stop blinking to indicate the heel position has been saved.
CALIBRATION PROCEDURE HEEL POSITION = MAX BEND –
1. Place the pedal on the surface where it will be used.
2. Rotate the Slammi back to the el position and hold it there while you he
press and release the CALIBRATE button once; the EHX logo begins to blink
indicating the heel position has been saved.
3. While the EHX logo blinks, tilt the pedal forward to the toe position allowing
the pedal sit flat on the surface. to
4. Press and release the CALIBRATE button once more.
5. The EHX logo will stop blinking to indicate the toe position has been saved.
If you accidentally press the CALIBRATE button and the EHX logo blinks, do not press
CALIBRATE again. After approximately 7 seconds, the Slammi will stop blinking and
ignore the button press.
Please Note: to reduce the total sweep range of the Slammi, when calibrating,
move the Slammi up a little when pressing the button to save the toe position or
move the Slammi forward a bit when pressing the button to save the heel position.
ENTERING/EXITING BYPASS
Switch between and effect mode by tipping the Slammi forward, in buffered bypass
the toe direction, past the flat position of the Slammi. You do not need to tip the
Slammi all the way forward; 25% of the total forward travel will do it. The Slammi
needs to return to its flat position before you can switch between bypass and effect
mode again.
When the Slammi is in effect mode, the EHX logo in the center of the pedal will light
up. In bypass mode, the logo does not light .
POWER
Plugging into the INPUT jack activates power from the internal 9 Volt battery. The
input cable should be removed when the unit is not in use to avoid running down the
battery. If an AC Adapter is used, the Slammi will be powered up as long as the AC
Adapter is correctly plugged in.
The Slammi’s power jack is located on the same side as the OUTPUT jack. A 9 Volt
AC Adapter capable of delivering at least 50 mA of current is required to power the
Slammi. The inner ring of the 9 Volt AC Adapter must be negative, the outer ring
positive. The optional 9V power supply from Electro-Harmonix is 9.6DC-200BI (same
as used by Boss® & Ibanez®) 9.6 Volts DC/200mA. The unit’s battery may be left in
or taken out when the AC Adapter is in use. The actual current draw of the
Slammi mA.is 24
CHANGING THE BATTERY
1. Locate the battery door at the front of the Slammi under the toe area of the ,
foot plate.
2. Remove the large black screw that holds the battery door to the case, most
coins or larger slotted screwdrivers can be used to remove this screw.
3. Connect your new 9V battery to the wired battery connector.
4. Insert the 9V battery into the battery holder clip on the battery door so that
the wired connector is on the same side of the hole in the battery door.
5. Place the battery door back into its window, in the case of the Slammi and
re-install the screw.
NOTES AND SPECIFICATIONS
• Slammi has buffered bypass.
• The input impedance presented at the INPUT Jack is 2M . The output
impedance at the OUTPUT Jack is . 780
• The current draw of the Slammi is mA. 24

Specyfikacje produktu

Marka: Electro Harmonix
Kategoria: Niesklasyfikowane
Model: Next Step Slammi

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Electro Harmonix Next Step Slammi, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Electro Harmonix

Electro Harmonix

Electro Harmonix Cock Fight Instrukcja

7 Października 2024
Electro Harmonix

Electro Harmonix Cock Fight Plus Instrukcja

7 Października 2024
Electro Harmonix

Electro Harmonix Holy Grail Max Instrukcja

7 Października 2024
Electro Harmonix

Electro Harmonix Spruce Goose Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix Germanium 4 Big Muff Pi Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix LPB-3 Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix Deluxe Memory Man 550-TT Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix 2X12 Speaker Cabinet Instrukcja

3 Października 2024
Electro Harmonix

Electro Harmonix Rerun Instrukcja

3 Października 2024
Electro Harmonix

Electro Harmonix 15Watt Instrukcja

30 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024