Instrukcja obsługi Electro Harmonix Neo Clone


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electro Harmonix Neo Clone (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
NEO CLONE
FULL CHORUS
Congratulations on your purchase of the Electro Harmonix ! The Neo Clone Neo
Clone is a compact battery operated Chorus effects pedal that features DEPTH and
RATE controls, True Bypass and an LED function indicator. To produce the Chorus
effect, the bends the frequency slightly from the input source and mixes Neo Clone
this altered signal with some direct unaffected signal. The combination produces a
doubling effect.
-OPERATING INSTRUCTIONS-
Plug your guitar into the jack and your amp into the jack, which is the INPUT AMP
Neo Clone’s output jack. Please note that as long as anything is plugged into the
INPUT, a drain is placed on your battery. It is recommended that you disconnect
the when the unit is not in use to extend battery life. INPUT
The DEPTH switch controls the amount of frequency change that occurs in the
altered signal. The speed of Chorus modulation is controlled by the knob. RATE
The red indicates when the effect is switched on. The footswitch toggles LED
between the Chorus effect and true bypass.
- - POWER
Power from the internal 9-volt battery is activated by plugging into the jack. INPUT
The input cable should be removed when the unit is not in use to avoid running down
the battery. If a battery eliminator is used, the Neo Clone will be powered up as long
as a wall-wart is plugged into the wall.
The barrel connector on the front of the Neo Clone is for a 9-volt battery eliminator
capable of delivering at least 25 mA of current. e optional 9V power supply from Th
Electro-Harmonix is 9.6DC-200BI (same as used by Boss™ & Ibanez™) 9.6 Volts DC
200mA. The inner ring of the 9-volt battery eliminator must be negative, the outer
ring positive. The unit’s battery may be left in or taken out when the eliminator is in
use. The actual current draw of the Neo Clone is 12 mA.
To change the 9-volt battery, you must remove the 4 screws on the bottom of the
Neo Clone. Once the screws are removed, you can take off the bottom plate and
change the battery. Please do not touch the circuit board while the bottom plate is off
or you risk damaging a component.
The input impedance presented at the Input Jack is . The output impedance at 220k
the Amp Jack is 1k .


Specyfikacje produktu

Marka: Electro Harmonix
Kategoria: Niesklasyfikowane
Model: Neo Clone

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Electro Harmonix Neo Clone, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane Electro Harmonix

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024