Instrukcja obsługi Electro Harmonix Mainframe Bit Crusher

Electro Harmonix Niesklasyfikowane Mainframe Bit Crusher

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electro Harmonix Mainframe Bit Crusher (12 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/12

Congratulations on your purchase of the MAINFRAME, a powerful but easy- -use to

sample rate reducer and bit crusher. Introducing old-school digital audio sounds

into your music has never been easier. A broad range of controls help you fine-

tune the digital artifacts, and the innovative Sample Rate Tuning Mode makes it

easy to match the sample reduction to a pitch, even on the fly. Access the

MAINFRAME and immerse your tone in the sounds of the arcades, consoles, and

terminals of yesteryear.

WARNING: Your Mainframe comes equipped with an Electro-Harmonix 9.6DC-200BI

power supply. The Mainframe requires at 9VDC with a center negative plug. Use 90mA

of the wrong adapter or a plug with the wrong polarity may damage your Mainframe and

void the warranty. Do not exceed 10 VDC on the power plug. Power supplies rated for .5

less than will cause the Mainframe to act unreliably. 90mA

- FEATURES -

 Sample Rate Reduction ranging from 48kHz to 110Hz

 Bit Depth Reduction ranging from -bit to 1-bit 24

 Selectable High/Low/Band-Pass filter to shape the artifacts of the bit crushing

and sample rate reduction

 Sample Rate Tuning Mode allows you to set the sample rate to match the key

of a song, or continu ly adjust the sample rate based on what you play on al

your instrument

 Programmable preset or expression pedal setting allows you to save your

sound or control any combination of the Mainframe’s knobs with an external

expression pedal

 Secondary knob parameters allow you to fine- tune the Mainframe’s effect

 High quality buffered bypass and silent switching

- SPECIFICATIONS -

  Audio input impedance: 2M

  Audio o put impedance the OUTPUT jackut : 500

 Current draw: mA 90

 Maximum input signal level: 6.25 dBu (4.5V peak- -peak) to

C C ONTROLS AND ONNECTIONS

1. VOL Knob This knob sets the master output level of the Mainframe.

2. BLEND Knob This knob blends between the dry guitar signal and the

effect signal. As the knob is turned clockwise, the output ranges from

completely dry guitar to a fully effected signal with the filter applied.

3. BIT DEPTH Knob As this knob is turned clockwise, the bit depth of

the signal is

reduced

, producing a distorted, noisy tone.

4. SAMPLE RATE Knob As this knob is turned clockwise, the sample

rate of the signal is

reduced

, producing a ringing or glitchy tone.

5. FILTER HPF/BPF/LPF Switch This toggle switch controls the

direction of the Mainframe’s filter:

HPF: High-Pass Filter

BPF: Band-Pass Filter

LPF: Low-Pass Filter

6. FILTER FREQ This knob controls the frequency of the Mainframe’s

filter. As the knob is turned up, the frequency increases. The frequencies

cut/passed by the filter vary by the filter type:

HPF: Frequencies above the FREQ knob setting are passed,

frequencies below are cut.

BPF: The FREQ knob controls the center frequency of a pass band.

Frequencies above and below this center frequency are cut.

LPF: Frequencies below the FREQ knob setting are passed,

frequencies above are cut.

Tip: For a tone with no filtering, set the FREQ knob to maximum and set

the toggle switch to LPF.

7. FILTER PEAK This knob controls the resonance of the Mainframe’s

filter. Turning this knob clockwise increases the resonance, producing a

sharper, more cutting tone.

8. EXP / PRESET Button and Green LED This button turns expression

mode or a saved preset on and off. When the Green LED is lit, expression

control is enabled, or the preset is enabled. See pages 6- for details on 9

how to save expression settings or a preset.

9. Footswitch and Red LED Press and release the footswitch to toggle

between bypass and effect modes. When the red LED is lit, the Mainframe

is in effect mode. Double tap the footswitch to enter Sample Rate Tuning

Mode, and tap it once again to exit Sample Rate Tuning Mode and save

the tuned sample rate.

10. INPUT Jack This 1/4" phone jack is the audio input of the

Mainframe. The input impedance is 2M . 

11. OUTPUT Jack This 1/4" phone jack is the main audio output of the

Mainframe The output impedance is 500 . . 

12. EXP Jack Connect an expression pedal or control voltage jack to

allow for external control over every knob on the Mainframe See pages .

6- for a description on how to set up and control the Mainframe with an 9

external expression pedal.

13. 9V Power Jack Plug the output of the Mainframe’s supplied

EHX9.6DC 200mA AC adapter to the 9V power jack located at the top of

the pedal. The Mainframe requires 90mA at 9VDC with a center-negative

plug. Do not exceed 10.5VDC on the power jack.

Specyfikacje produktu

Marka:	Electro Harmonix
Kategoria:	Niesklasyfikowane
Model:	Mainframe Bit Crusher

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Electro Harmonix Mainframe Bit Crusher, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Electro Harmonix

Electro Harmonix Cock Fight Instrukcja

7 Października 2024

Electro Harmonix Cock Fight Plus Instrukcja

7 Października 2024

Electro Harmonix Holy Grail Max Instrukcja

7 Października 2024

Electro Harmonix Spruce Goose Instrukcja

5 Października 2024

Electro Harmonix Germanium 4 Big Muff Pi Instrukcja

5 Października 2024

Electro Harmonix LPB-3 Instrukcja

5 Października 2024

Electro Harmonix Deluxe Memory Man 550-TT Instrukcja

5 Października 2024

Electro Harmonix 2X12 Speaker Cabinet Instrukcja

3 Października 2024

Electro Harmonix Rerun Instrukcja

3 Października 2024

Electro Harmonix 15Watt Instrukcja

30 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024

Stihl HT 70 Instrukcja

15 Października 2024

Ernesto H14270 Instrukcja

15 Października 2024

Uniden BT MIC KIT Instrukcja

15 Października 2024

Vaude Omnis Bike 26 Instrukcja

15 Października 2024

ART ProChannel II Instrukcja

15 Października 2024

Aukey DR02J Instrukcja

15 Października 2024

Master Lock 653EURD Instrukcja

15 Października 2024

Roland FR-18 Diatonic Instrukcja

15 Października 2024