Instrukcja obsługi Electro Harmonix Hell Melter

Electro Harmonix Niesklasyfikowane Hell Melter

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Electro Harmonix Hell Melter (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
Congratulations, you are now possessed by the Hell Melter. This device
is built to produce the legendary ‘chainsaw’ distortion tone, but with
added features that expand the threat of tonal destruction. Do you
want the gruesome vintage grind found on classic death metal records?
Do you seek added volume, distortion, clarity, or control? Sink deep
into the Hell Melter and you shall nd all the havoc you’ll ever need.
Operating Instructions
Connect your guitar to the INPUT jack of the Hell Melter and the OUTPUT
jack to your amp’s input. Plug in the included power supply and plug its
output plug into the Hell Melter’s power jack. Press the EFFECT footswitch
to ensure the red LED is lit, and the Hell Melter is ready.
A good starting point is to turn all the knobs (except for DRY LVL and GATE)
to their maximum positions and play the heaviest riffs you've got. Setting
all the EQ knobs to maximum, including MID FREQ, produces the uniquely
punchy “chainsaw” sound that has powered countless heavy bands.
Note: the original circuit that produced this sound used components
with wide tolerances, resulting in noticeable tone differences from unit
to unit. The Hell Melter can recreate many of these different tones with
slight tweaks near the maximum position of the MID FREQ knob.
POWER SUPPY REQUIREMENTS:
Voltage: Current: 9VDC 140mA Center-Negative Polarity:
This device comes equipped with an Electro-Harmonix 9.6DC-200 power supply. Use of the wrong adapt-
er or a plug with the wrong polarity may damage the device and void the warranty. Do not exceed 12VDC
on the power plug. Power supplies rated for less than 140mA can cause the device to act unreliably
Advanced Heavy Metal Distortion
- 2 -
1. DISTORTION Knob Adjusts the amount of distortion and saturation, from a
light grind to a roaring chainsaw. Turn clockwise for more distortion.
2. LEVEL Knob Adjusts the overall output level of the Hell Melter. Turn clockwise
for more output. More output is available than on the original ‘chainsaw’ circuit.
3. LOW Knob Provides active boost or cut to the bass frequency range. The middle
position leaves bass frequencies at.
4. MID LVL Knob Provides active boost or cut to the mid frequency, with the
frequency set by the MID FREQ knob. The middle position leaves mid frequen-
cies at.
5. MID FREQ Knob Adjusts the frequency boosted or cut by the MID LVL knob.
Turn the knob clockwise to increase the frequency.
Controls and Connections
- 3 -
6. HIGH Knob Provides active boost or cut to high frequencies. The middle posi-
tion leaves high frequencies at. Tip: the frequencies controlled by the HIGH
Knob are slightly lower than a typical ‘treble’ control, allowing you to produce
searing highs without a lot of treble harshness. To emphasize even higher
‘treble’ frequencies, turn the HIGH knob below the middle position, and increase
the LEVEL knob to re-emphasize treble.
7. NORM/BURN Switch Switches between “Normal” and “Burn” Modes:
Normal Mode The famous vintage chainsaw distortion sound.
Burn Mode A custom, modernized distortion sound, utilizing higher voltage
rails and alternative clipping options. This results in a less compressed and
more open distortion sound with a more pronounced attack.
8. GATE Mini Knob Removes unwanted hum by adjusting the noise oor thresh-
old. The gate mutes the OUTPUT jack when the signal at the INPUT jack is below
the threshold setting of the GATE knob. As GATE is turned clockwise, a louder
guitar signal at the INPUT jack is required to unmute the OUTPUT jack. Set GATE
fully counter-clockwise to disable.
Setting the GATE knob: Start with GATE fully counterclockwise, DIST above noon,
and your guitar volume at max. You may want to hold the strings so they don’t
ring out. Slowly turn GATE clockwise until the Hell Melter mutes. Now turn GATE
a little further clockwise and then test it. If you have to play with too much force
to unmute the gate, then turn GATE a little counter-clockwise. If you want the
gate to act more quickly at the end of notes, then turn GATE further clockwise.
9. DRY LVL Mini Knob Adds clean, undistorted input signal to the output. As the
knob is turned clockwise, the amount of dry signal increases. At the minimum
position, no dry signal is mixed into the output. Tip: this is especially useful to
maintain note clarity when stacking the Hell Melter with a dirty amp or another
gain pedal.
10. EFFECT Footswitch and Red LED This footswitch engages or bypasses the
effect. The LED lights when the effect is active. The Hell Melter employs high
quality buffered bypass.
11. BOOST Footswitch and Yellow LED This footswitch engages Boost Mode, add-
ing extra gain at the input of the circuit, and adjustable volume boost.
12. BOOST LEVEL Internal Trimmer This trimmer controls the additional volume
added when Boost Mode is active. To access it, remove the 4 screws on the back
plate of the Hell Melter, and locate the trimmer next to the BOOST Footswitch.
Taking care not to touch the rest of the circuitry of the board, turn this trimmer
clockwise using a small at-head screwdriver to increase the volume boost. At
the minimum position, Boost Mode provides no volume boost.
13. INPUT Jack Audio input to the Hell Melter.
14. OUTPUT Jack Audio output from the Hell Melter.
15. 9V Power Jack Attach the output plug from the included power supply to the
9V power jack. The Hell Melter draws 140mA at 9VDC on a center-negative plug.
Do not exceed 12VDC on the power jack. The Hell Melter does not take batteries.

Specyfikacje produktu

Marka: Electro Harmonix
Kategoria: Niesklasyfikowane
Model: Hell Melter

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Electro Harmonix Hell Melter, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Electro Harmonix

Electro Harmonix

Electro Harmonix Cock Fight Instrukcja

7 Października 2024
Electro Harmonix

Electro Harmonix Cock Fight Plus Instrukcja

7 Października 2024
Electro Harmonix

Electro Harmonix Holy Grail Max Instrukcja

7 Października 2024
Electro Harmonix

Electro Harmonix Spruce Goose Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix Germanium 4 Big Muff Pi Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix LPB-3 Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix Deluxe Memory Man 550-TT Instrukcja

5 Października 2024
Electro Harmonix

Electro Harmonix 2X12 Speaker Cabinet Instrukcja

3 Października 2024
Electro Harmonix

Electro Harmonix Rerun Instrukcja

3 Października 2024
Electro Harmonix

Electro Harmonix 15Watt Instrukcja

30 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024