Instrukcja obs艂ugi Edimax ES-3105P

Edimax Schakelaar ES-3105P

Przeczytaj poni偶ej 馃摉 instrukcj臋 obs艂ugi w j臋zyku polskim dla Edimax ES-3105P (1 stron) w kategorii Schakelaar. Ta instrukcja by艂a pomocna dla 4 os贸b i zosta艂a oceniona przez 2 u偶ytkownik贸w na 艣rednio 4.5 gwiazdek

Strona 1/1
(2) LED
Table 1-1 LED description
Power is supplied
No power
LED Color Status Description
PWR
(Power) Green Lit
Off
A valid link is established
No link is established
Data packets received
Off
LNK/ACT
(Link/Activity)
SPEED
(10/100M)
Green
Yellow
Lit
Off
Lit This port run at 100Mbps
This port run at 10Mbps
Flash
5/8/16 Port Fast Ethernet Switch
2
2Installation
1. Operating Environment
This switching hub must be installed and operated within the limits of
specified operating temperature (32-1310F) and humidity (10-95%
Noncondensing). Do not place objects on top of the unit. Do not obstruct any
vents at the sides of the unit. Do not position the unit near any heating source
such as heater, radiator, or direct exposure to sun. Prevent entering of water
and moisture into the unit. If necessary, use dehumidifier to reduce humidity.
2. Connecting to network devices
The RJ-45 ports on the switch support Auto-MDI/MDI-X function which
allow using straight-through or cross-over type cables to connect this switch
to workstation or hub.
Connect one end of the network cable to the RJ-45 port on the rear panel, and
connect the other end of the network cable to the RJ-45 port on the network
device. Follow the same procedure to connect all the RJ-45 ports of the
switch. The UTP network cables must comply with EIA/TIA 568
specifications and Category 5 standard for 100Mbps data transmission.
Maximum length, using UTP cable, between the switch and connected device
is 100 meters (300ft). Once the network cable is connected to both ends and
the attached network device is powered on, the green LNK/ACT LED should
be lit.
3. Connecting the power
Connect the output end of the power
adapter to the power connector on the
rear panel of the unit. Connect the
power adapter to the power outlet.
The green Power LED on the front
panel should be lit. Figure 2-1 Connect the AC power adapter
DC Power
AC Power
External Power Adapter
3
3Trouble-shooting
1. Power LED is not lit
zCheck if the power cord is properly connected to the external power
adapter and the power outlet. Make sure the DC power jack is firmly
plugged into the power socket of the switch.
2. Link/Activity is not lit when connect to 100Mbps device
zCheck the power switch of the network device attached to the switch;
make sure it is turned ON.
zCheck the network cable; make sure it is properly connected to the
switch and the network device.
zCheck the network cable; make sure the UTP cables comply with
EIA/TIA 568 and Category 5 specification.
[!] Contact your dealer if problem persist.
1
1Physical Description
(1) Panel
Figure 1-1 Panel description
Power LED
LED Panel
RJ45 Connectors
Power Connector
POWER
100M
LNK/ACT
Fast Ethernet Switch
41 52 63 7 8
10/100M LED
Link/Activity LED
8-Port 10/100Mbps
LED Panel
Power LED 100/10Mbps LED
Link/Activity LED
POWE R
10 0M
LNK/ACT
Fast Ethernet Switch 12345
RJ45 Connectors
Power Connector
5-Port 10/100Mbps
POWER
100M
LN K/ ACT
3 112 101 94 125 136 147 158 16
Fast Ethernet Switch
LED Panel
RJ45 Connectors
Power Connector
100/10Mbps
Link/Activity LED
Power LED
16-Port 10/100Mbps
5-Port
8-Port
16-Port

Specyfikacje produktu

Marka: Edimax
Kategoria: Schakelaar
Model: ES-3105P

Potrzebujesz pomocy?

Je艣li potrzebujesz pomocy z Edimax ES-3105P, zadaj pytanie poni偶ej, a inni u偶ytkownicy Ci odpowiedz膮




Instrukcje Schakelaar Edimax

Instrukcje Schakelaar

Najnowsze instrukcje dla Schakelaar

ATen

ATen CE610-AT-E Instrukcja

19 Wrze艣nia 2024
ATen

ATen KA7240S Instrukcja

19 Wrze艣nia 2024
Lindy

Lindy 38155 Instrukcja

19 Wrze艣nia 2024
ATen

ATen VS0801H Instrukcja

19 Wrze艣nia 2024
ATen

ATen KE9950 Instrukcja

19 Wrze艣nia 2024
OSD Audio

OSD Audio SSVC4 Instrukcja

18 Wrze艣nia 2024
ATen

ATen CS1794 Instrukcja

18 Wrze艣nia 2024