Instrukcja obsługi Edifier C2V

Edifier głośnik C2V

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Edifier C2V (1 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/1

English

www.edifier.com

EDIFIER INTERNATIONAL LIMITED

Made in China

NOTICE:

For the need of technical improvement and system upgrade,

information contained herein may be subject to change

from time to time without prior notice

Manual Edition 1.1 , Dec. 2007

Printed in China

1 2

EnglishEnglish

3 4

EnglishEnglish

5 6

EnglishEnglish

7 8

EnglishEnglish

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTION Unpack the box

Box content

Amplifier

Subwoofer

2 satellite speakers

Remote control (RC30)

3.5mm to dual RCA connector cable

User's manual

Amplifier

Subwoofer

Remote control (RC30)User's manual

3.5mm to dual RCA connector cable

Satellite speaker

Illustrations and Functional Depict

1. Power on/stand-by button

2. Audio signal input status indicator

3. Audio signal input socket

4. Display window and IR receiver

5. Mode adjustment indicator

6. Audio signal output socket

7. “VOLUME” volume adjustment knob

8. Working indicator (halo)

9. “FUNCTION” function buttons

10. “INPUT” Input selection button

11. Headphone jack

12. Power switch

Front view of amplifier Rear view of amplifier

Making connections

Left satellite speaker

To A.C

Subwoofer

Right satellite speaker

Operational guidance Guidance for using remote control

Operational guidance

1. Connect the speakers and audio source

Please refer to illustrations in "Making connections"

2. Power on/off the system

Plug the power cord and turn on the power switch, the digital display will show "- -", indicating that system is in STBY mode.

Press the " " button on amplifier or " " key on remote control, the power indicator and PC input indicator will be lit; digits

shown in the digital display will run from "0" to "30", the default level of master volume. System now enters working mode.

Rotate the " " knob to adjust master volume, from 0 to 60. "0" means minimum, "60" for maximum.

Press the " " key on amplifier or " " key on remote control when system in working mode will set it back to STBY.

3. Input selection

The system has "PC" and "CD/AUX" inputs, and "PC" is the default input. Press the "INPUT" selector on front deck of

amplifier to switch between "PC" and "CD/AUX" inputs, the digital display will show the name of current input ("PC" or "CD").

4. Trimmers / control

Press the "Function" key when system in working mode, the "Bass" and "Treb" trimmer indicators will be lit sequentially:

when "Bass" lit, bass trimmer on; when "Treb" lit, treble trimmer on; when both off, back to master volume control.

The digital display will show corresponding trimmer / control value: when "Bass" lit, figure shown is bass trimmer value;

when "Treb" lit, it is treble trimmer value; when both off, it is master volume level.

Rotate " " knob to adjust the trimmers / control: when "Bass" lit, rotate the " " knob to adjust the bass

trimmer from -9 to +9; when "Treb" lit, rotate to adjust the treble trimmer from -7 to +7; when both off, rotate to adjust

the master volume.

3 seconds no action in trimmer mode, system will go back to master volume adjustment, with both trimmer indicators off

and digital display shows current master volume level.

5. Headphone output

Plug the headphone plug into the " " on amplifier's front deck. It works correctly if the output from speaker is shut and

power indicator off. " " knob can control the headphone output and digital display shows the current master

volume level.

Point the remote control to the IR window on front deck of amplifier when operating the remote control.

The optimum operational distance is 7 meters. When a remote command is received and executed,

figures shown in digital display will blink.

1. " " -- STBY/ON key

Press this button will set the system on / STBY.

2. "MUTE"

Press this button when system in working mode will instantly shut off the

speaker output. The power indicator is still on and digital display blinks

current master volume level.

Press one more time this button will recall the speaker output.

3. "Volume +/-" keys

Adjust the master volume level from 0 to 60.

4. "SW +/-" keys

Bass trimmer adjustment. When press the keys, the "Bass" trimmer

indicator will be lit and digital display shows the value.

5. "TRE +/-" keys

Treble trimmer adjustment. When press the keys, the "Treb" trimmer

indicator will be lit and digital display shows the value.

6. "PC / AUX" keys

Input selectors. Press the "PC" key, system gets signal from "PC" input,

and "PC" input indicator lit; press the "AUX" key, system gets signal from

"CD/AUX" input, and "AUX" input indicator lit.

Note: "SW +/-" and "TRE +/-" are trimmer adjustments which are both tone controls based on master volume level.

"SW +/-" ranges from -9 to +9; "TRE +/-" ranges from -7 to +7; minus figure refers to attenuation, positive for boost,

and "0" for no boost and no attenuation. 3 seconds no action in trimmer mode, the system will return to master

volume adjustment.

Battery loading:

Please refer to the figure on the right side to open the battery compartment,

load the included C2025 battery and shut the compartment.

The battery (battery or batteries or battery pack) shall not be exposed to

excessive heat such as sunshine, fire or the like.

Note:

• Do not place the remote in places that are hot and moist;

• Unload the battery when unused for long period of time.

Specification

Amplifier power output: Satellite channel: RMS 6W X 2 (THD+N=10%)

Subwoofer channel: RMS 18W (THD+N=10%)

Signal-to-Noise Ratio(Amplifier): ≥85dBA

Distortion: ≤0.5%

Input impedance: 10K ohm

Input Sensitivity: R/L: 300mV±50mV

SW: 150mV±50mV

Volume control: Front panel controls for volume and Bass level adjustments,

remote control

Bass Unit: 6.5 inch (166mm), Magnetically Shielded, 4 Ohm.

Midrange Unit: 3 inch (78mm) , Magnetically Shielded, 4 Ohm.

Tweeter Unit: 3/4 inch PV membrane dome, Magnetically Shielded, 8 Ohm.

Power input: 100V-120V ~, 50/60Hz (for USA/Canada/Japan models)

220V-240V ~, 50/60Hz (for European/China/Korea/South

America, etc.models)

Dimension: Amplifier: 72(W)x223(H)x213(D) mm

Subwoofer: 246(W)x252(H)x271(D) mm

Satellite: 90(W)x181(H)x137(D)mm

Weight: Approx. 9.2kg

Warnings:

Please do not feed powered signal from another amplifier into the input ports of this system!

Please adjust to a comfortable volume to avoid damaging your hearing and the system!

Dangerous voltage inside the subwoofer enclosure, please do not open the chassis.

Refer to qualified personnel for servicing.

Please remove the power plug if the system is unused for long period of time.

Please do not expose the system in rain or moisture environment.

Please do not place vase or utensil full of liquid on the speaker.

Troubleshooting

Not all speakers function:

Please first check if the speaker wires are connected securely;

then check if the Line-in connectors are reversed; check also if the audio source is at fault.

One satellite speaker does not function when playing CD from computer:

This kind of phenomena is prone to happen on new computer systems that one satellite

does not function when playing CD, but system works fine when playing WAV formatted files.

This is mainly due to the fault connection of CD-ROM and sound card, that one channel of

signal is shorted to the ground.

Please refer to the manual of CD-ROM and sound card to adjust the wire connection.

System does not work at all

1. Please check if power is connected, and if the wall outlet is switched on.

2. Please check if the amplifier is still in STBY mode

3. Please check if the master volume is turned to minimum

4. Please check if the audio input cable is connected correctly

5. Please check if there is signal from audio source

Noise coming from speakers

Amplifier circuitry of this product generates little noise, while the background noise of

some VCD/DVD player or computer sound card are too high.

Please keep the system in active mode and remove the audio source, if no sound can

be heard at 1 meter away from the system, then there is no problem with this product.

Magnetic interference

This system is complete magnetically shielded, and can be placed near TV or monitor.

But since magnet of the subwoofer driver is large, some magnetism leakage is inevitable

when the system is too close to the monitor, and it is recommended to keep a 1 meter

distance between the speaker system and monitor or TV set.

If you have any further questions or concerns regarding Edifier Products

Please visit our website at: www.edifier.com, or email Edifier Support for further

assistance at: main@edifier.com, If you prefer, you may contact us by phone,

Toll Free: 1-877-EDIFIER (334-3437).

1. Connecting the speakers

Please connect the left and right satellite speakers to the back panel of the external amplifer as indicated in

the diagram.

2. Connecting the system to the audio source

Please connect the sound card of your PC or other audio sources to the PC IN input connector with

the 3.5mm to dual RCA audio connecting cable, Connect Aux sources to aux input socket.

3. Connect to the power

Connect the power plug to an AC outlet, and please match the correct voltage for your area.

Specyfikacje produktu

Marka:	Edifier
Kategoria:	głośnik
Model:	C2V

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Edifier C2V, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje głośnik Edifier

Edifier M1250 Instrukcja

14 Stycznia 2025

Edifier Luna Eclipse HD e25HD Instrukcja

31 Grudnia 2025

Edifier R2750DB Instrukcja

31 Grudnia 2025

Edifier R1380T Instrukcja

31 Grudnia 2025

Edifier R1280Ts Instrukcja

31 Grudnia 2025

Edifier Hecate G1500 SE Instrukcja

31 Grudnia 2025

Edifier MR3 Instrukcja

9 Października 2024

Edifier R990BT Instrukcja

5 Października 2024

Edifier Luna Eclipse e25 Instrukcja

4 Października 2024

Edifier D32 Instrukcja

4 Października 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025

ION Insta Sound Instrukcja

15 Stycznia 2025

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025

Yamaha WX-010 Instrukcja

15 Stycznia 2025

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025