Instrukcja obsługi Dürkopp Adler 743-121-01
Dürkopp Adler
maszyna do szycia
743-121-01
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dürkopp Adler 743-121-01 (102 stron) w kategorii maszyna do szycia. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/102
743-121-01
Service Instructions
All rights reserved.
Property of Dürkopp Adler AG and protected by copyright. Any reuse of these contents,
including extracts, is prohibited without the prior written approval of Dürkopp Adler AG.
Copyright © Dürkopp Adler AG 2018
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Table of Contents
Service Instructions 743-121-01 - 01.0 - 09/2018 1
1 About these instructions ........................................................... 3
1.1 For whom are these instructions intended?.................................. 3
1.2 Representation conventions – symbols and characters ............... 3
1.3 Other documents .......................................................................... 5
1.4 Liability.......................................................................................... 5
2 Safety........................................................................................... 7
2.1 Basic safety instructions ............................................................... 7
2.2 Signal words and symbols used in warnings................................ 8
3 Working basis ........................................................................... 11
3.1 Order of the settings ................................................................... 11
3.2 Laying the cable guide................................................................ 11
3.3 Screws in safety covers.............................................................. 12
3.4 Removing the covers.................................................................. 12
3.4.1 Swiveling up the machine head.................................................. 13
3.4.2 Removing and fitting the head cover .......................................... 14
3.4.3 Removing and fitting the arm cover............................................ 15
3.4.4 Removing and fitting the sliding plate......................................... 15
3.5 Flats on shafts ............................................................................ 16
4 Setting the machine head ........................................................ 17
4.1 Gages ......................................................................................... 17
4.2 Setting the adjusting disk............................................................ 18
4.3 Setting the arm shaft crank......................................................... 19
4.4 Needle evasive movement ......................................................... 20
4.4.1 Setting the needle evasive moment ........................................... 20
4.4.2 Adjusting the needle evasive moment........................................ 20
4.5 Setting the thread tensioning spring ........................................... 21
4.6 Setting the symmetry of the looper motion ................................. 22
4.7 Setting the looper ....................................................................... 23
4.8 Setting the needle bar height...................................................... 24
4.9 Setting the needle guard ............................................................ 25
4.10 Setting the thread take-up disk................................................... 26
4.11 Setting the rocker bolt and the left lower shaft bearing .............. 27
4.12 Setting the looper drive housing ................................................. 28
4.13 Setting the position sensor ......................................................... 29
4.14 Replacing the right arm shaft bearing......................................... 30
4.15 Replacing the pressure regulator ............................................... 31
5 Setting the sewing unit ............................................................ 33
5.1 Setting the thread cutter ............................................................. 33
5.1.1 Removing the thread cutter ........................................................ 34
5.1.2 Installing the thread cutter .......................................................... 34
5.1.3 Setting the support bracket......................................................... 34
5.1.4 Checking the functionality of the thread cutter ........................... 35
5.1.5 Installing and removing the blade............................................... 35
5.1.6 Replacing the piston ................................................................... 38
5.2 Setting the folding table .............................................................. 39
5.2.1 Setting the folding table retraction .............................................. 40
5.2.2 Setting the angle adjustment ...................................................... 41
5.3 Setting the transport carriage ..................................................... 43
Specyfikacje produktu
Marka: | Dürkopp Adler |
Kategoria: | maszyna do szycia |
Model: | 743-121-01 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Dürkopp Adler 743-121-01, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje maszyna do szycia Dürkopp Adler
31 Maja 2024
31 Maja 2024
Instrukcje maszyna do szycia
- maszyna do szycia SilverCrest
- maszyna do szycia Toyota
- maszyna do szycia Singer
- maszyna do szycia Medion
- maszyna do szycia Brother
- maszyna do szycia Husqvarna
- maszyna do szycia Baby Lock
- maszyna do szycia Victoria
- maszyna do szycia Bernina
- maszyna do szycia Huskystar
- maszyna do szycia Pfaff
- maszyna do szycia Husqvarna-Viking
- maszyna do szycia Carina
- maszyna do szycia Minerva
Najnowsze instrukcje dla maszyna do szycia
6 Lipca 2024
28 Czerwca 2024
27 Czerwca 2024
27 Czerwca 2024
26 Czerwca 2024
26 Czerwca 2024
18 Czerwca 2024
11 Czerwca 2024
29 Maja 2024
28 Maja 2024