Instrukcja obsługi Dormakaba RCI F1119

Dormakaba nieskategoryzowany RCI F1119

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dormakaba RCI F1119 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
I N S T A L L A T I O N
© 2015 RutheRfoRd ContRols Int’l | A doRMA GRoup CoMpAny
www.rutherfordcontrols.com • Phone: 1.800.265.6630 • fax: 1.800.482.9795 • e-mail: sales@rutherfordcontrols.com
When installing an electric strike on an inactive door of a set of double doors, it can be treated the same as a frame installation in most situations. For
more information contact the Technical Service Department at 1-800-265-6630 or 519-621-7651.
Fire labeled heavy-duty electric strike
F1119
isf1119 Pcn14079
r06/15Gr-1
INSTRUCTIONS
1. To determine if the Strike Shim positions need adjustment, measure dimension “R” (see Figure 1) from the center to the edge
of the latch. When necessary rearrange Strike Shims according to the chart below. The “shipped as default” positions are
illustrated in Figure 2.
SHIM PLACEMENT CHART
Note: Shims consist of two thin and one thick. Install with the indicated hardware per the appropriate measurement R range.
Shipped as Default
Figure #1 Figure #2
S1 S2
“R” distance
from center to
edge of latch
“R” distance from
center to edge of latch
Deadlock
Trigger
Deadlock
Trigger
Mortise Lock Cylindrical Lock
Measurement “R” “S1” Shims “S1” Screws “S2” Shims “S2” Screws
5/16” (8.2mm) or Less None M4 x 10mm 1 thick, 2 thin M4 x 10mm
5/16” - 3/8”, (8.2 - 9.7mm) 1 thin M4 x 10mm 1 thick, 1 thin M4 x 10mm
3/8” - 7/16”, (9.7 - 10.7mm) 1 thick M4 x 10mm 2 thin M4 x 10mm
7/16” - 1/2”, (10.7 - 12.2mm) 1 thick, 1 thin M4 x 14mm 1 thin M4 x 10mm
1/2” - 9/16” (12.2 - 13.7mm) 1 thick, 2 thin M4 x 14mm none none
INSTRUCTIONS Cont’d.
2. Determine the horizontal centerline.
FOR MORTISE LOCKS: Position the strike against the edge of
the door with the deadlock trigger fully on the strike’s angled
ramp and the latch within the strike cavity. Move door close to
the frame. The horizontal centerline is clearly molded into the
strike’s pry-guard. Transfer onto door frame.
FOR CYLINDRICAL LOCKS: Simply align the center of the
latch with the center of the strike cavity. Move door close to
the frame. The horizontal centerline is clearly molded into the
strike’s pry-guard. Transfer onto door frame.
3. Determine the vertical centerline of the door lock face,
carefully considering any stops or gasket and transfer onto
the door frame.
4. Use the vertical and horizontal centerlines marked on the
drawing below to prepare the door frame for cutting.
5. If required, install the optional “no weld” mounting brackets
as per the instructions included with the mounting brackets
in the hardware pack.
6. Connect the incoming wiring from the power supply to the
terminal screws on the strike insert. RCI door strikes are
not polarity sensitive although be certain to observe proper
polarity if a suppression diode is required for access control
applications. To meet BHMA A156.31 install the MOV
provided across the red & black power wires.
7. Install the door strike in the door frame using the screws
provided.
I N S T A L L A T I O N
Fire labeled heavy-duty electric strike
F1119
© 2015 RutheRfoRd ContRols Int’l | A doRMA GRoup CoMpAny
www.rutherfordcontrols.com • Phone: 1.800.265.6630 • fax: 1.800.482.9795 • e-mail: sales@rutherfordcontrols.com
F1119
Vertical Centre Line of Door
Lock and Mounting Face Plate
A 1 3/8” 1.38 34.9
B 9” 9.0 228.6
C 3-3/4” 3.75 95.3
D 1 1/2” 1.50 38.1
E 5/16” 0.31 7.8
F 5/32” 1.56 4.0
G 1-7/8” 1.88 47.6
X
K 8-3/8” 8.38 213.0
M 12-24 N/A N/A
MEASUREMENT
FRACTIONAL
INCHES
DECIMAL
INCHES
METRIC
mm
In or Out... we make it Easy!®
NOTE: Specifications subject to change without notice.
* Dimension F is measured from face of mounting tab to face of frame.
MOUNTING TAB KIT INSTRUCTIONS
Mounting tab kit is for use with aluminum and steel frames that
do not have factory installed mounting tabs for electric strike
installation.
1. Prepare the frame as shown in the installation instructions
(shipped separately with corresponding products). Fasten
the mounting tabs to the faceplate of the strike, selecting the
appropriate shims for your installation.
2. Using the assembled strike and tabs as a template, place
against the frame and mark the mounting hole locations.
Remove and drill a 3/16” hole in frame for each mounting tab
and countersink the frame.
3. Remove the tabs from the faceplate and install in the frame
using the 12-24 x 3/8” machine screws supplied. Tabs are zinc
plated and drilled and tapped for this purpose.
4. Make final electrical connections as described in installation
instructions (separate) and mount strike to the tabs with the
12-24 x 3/8” machine screws.
Frame
Self-Adhesive
Mounting Shim (8
incl.)
Mounting bTa
(2 incl.)
12-24 Machine
Screws (2 each to
keep tab straight)

Specyfikacje produktu

Marka: Dormakaba
Kategoria: nieskategoryzowany
Model: RCI F1119

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Dormakaba RCI F1119, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Dormakaba

Dormakaba

Dormakaba Master Key Systems Instrukcja

31 Sierpnia 2024
Dormakaba

Dormakaba CL700 Instrukcja

31 Sierpnia 2024
Dormakaba

Dormakaba C500 Instrukcja

31 Sierpnia 2024
Dormakaba

Dormakaba D800 Instrukcja

31 Sierpnia 2024
Dormakaba

Dormakaba 9321 Instrukcja

31 Sierpnia 2024
Dormakaba

Dormakaba 9320 Instrukcja

31 Sierpnia 2024
Dormakaba

Dormakaba C100 Instrukcja

31 Sierpnia 2024
Dormakaba

Dormakaba C200 Instrukcja

31 Sierpnia 2024
Dormakaba

Dormakaba Keyscan Indala Instrukcja

31 Sierpnia 2024
Dormakaba

Dormakaba ED250 Instrukcja

31 Sierpnia 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024