Instrukcja obsługi Dormakaba RCI 8310IQ

Dormakaba nieskategoryzowany RCI 8310IQ

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dormakaba RCI 8310IQ (6 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/6

INSTALLATION

RCI 8310IQ / 8320IQ

INTELLIMAG ELECTROMAGNETIC LOCKS®

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

Pre-Installation Instructions

1. This product must be installed according to all applicable

building and life safety codes.

2. Due to the variety of mounting configurations available with

this product, a survey and assessment of the physical area in

which the product will be installed must be performed.

3. The door frame must be inspected and deemed structurally

sound prior to installation of the electromagnetic lock. The

structural integrity of the mounting surfaces must be strong

enough to meet or exceed the holding force of the product.

4. The product must be protected from potential damage due to

intruders or tampering.

5. The product should be installed in a location that will not

hinder or create a potential safety hazard to authorized

personnel accessing the protected area.

6. Because electromagnetic locks are used in a variety of

applications and different door frame configurations, an

experienced installer with knowledge of this product must

make a determination of the optimal mounting method for this

specific application.

7. The components, hardware, installation instructions and

mounting template included with this product are intended for

use on outswinging doors.

8. Do not install this product on the exterior of buildings.

9. Do not use as a doorstop. This will void warranty.

10. Separate accessories must be used in the following

applications:

• Inswinging doors

• Narrow head jamb situations or center-hung doors

• Wherever there is insufficient space on the door

frame header to mount the lock

• Glass or Herculite doors that don’t have a door frame

• Hollow metal or wood frames where the door

stop is not thick enough to allow the product to

be installed

• Wherever an obstruction in the door prevents

installation of the armature plate at a proper height

• Doors that do not permit the armature plate to

be mounted low enough to meet the magnet

surface

Refer to the page 5 & 6 Product Accessories Guide for

further information. Accessories may impact holding force.

11. Installation of this product should be done by an

experienced installer with knowledge of this product.

NOTE: It is highly recommended that thread locking

compound be applied to all screws during installation to

reduce chance of screws loosening over extended time.

IS8310-IQ PCN18040

R08-19GR-1

1. Mount the electromagnetic lock to the door frame as outlined

on the installation template included with the product.

NOTE: During installation of the armature plate to the door it is

essential that the armature plate remains movable. The armature

plate must be allowed to pivot on the center-mounting bolt to

allow proper alignment with the magnet surface. If the plate is not

aligned with the magnet surface, the lock may lose holding force

or not lock at all.

The head of the armature mounting bolt ships with a rubber

washer affixed to it. This washer should project slightly beyond

the surface of the armature plate. This is to allow the washer

to expand when power is removed and break the air vacuum

between the plate and the magnet surface. If this washer is

removed or trimmed the lock will appear to have some holding

force even when power is removed.

For added safety, thread locking compound has been provided

for the armature plate bolt and the four captive electromagnetic

lock mounting screws.

WARNING: Improper installation, maintenance, inspection

or usage of the product or any related accessories or parts

may cause the electromagnetic lock, armature plate and

associated hardware to disengage and fall, causing serious

bodily injury and property damage. dormakaba Canada Inc.

and/or dormakaba USA Inc. will not be liable to the installer,

purchaser, end user or anyone else for damage or injury

to person or property due to improper installation, care,

storage, handling, maintenance, inspection, abuse, misuse

or act of God or nature involving this product or any related

accessories or parts.

2. Route the power supply connecting wire through the door

frame and into the wire access hole in the top of the magnet

housing. Connecting wire should be of sufficient gauge for

the lock being installed and the distance being run.

Installation Instructions

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO

THE END-USER UPON COMPLETION OF THE INSTALLATION.

3. Set the DC voltage jumpers on JP1 as follows.

For 12V operation two jumpers are used; One on the

two upper pins and the other on the two lower ones.

For 24V operation only one jumper is used to connect

the two center pins (factory setting)

Connect the positive (+) lead from the power supply to

TB1-1. Connect the negative (-) lead from the power

supply to TB1-2. For wiring installations, refer to figure

4. Delayed Relock Feature - The delayed relock feature can

be used to momentarily release the lock and keep it

unlocked for a time period from 0 to 90 seconds. The

time delay for this feature can be adjusted by carefully

turning the potentiometer in a counterclockwise

direction to increase delay time. Factory setting is zero

seconds (fully clockwise).

NOTE: On the 8320IQ double-door model turn both

potentiometers counterclockwise to increase the relock

delay.

JP1

JP2

TB1

Alarm Time Setting

Voltage Selection

Light Emitting

Diode (LED)

Time Delay Setting (0-90 secs)

CCW increases time delay

N.C

N.O.

Common

N.C

N.O.

Common

-Common (Ground)

+12/24VDC input

Bond Alert Sensor*

Output contacts SPDT rated at

2.0A @ 30VDC max

Magnet power from

Power Supply

Alarm Status*

Output contacts SPDT rated

2.0A @ 30VDC max.

Power Input Requirements

MODEL 12VDC 24VDC

8310IQ 0.59A 0.29A

8320IQ 1.18A 0.58A

*Shown with Door Open/unlocked

Fig. 1 – Wiring Schematic

Electromagnetic locks must conform to local fire codes, National Building Codes and Life Safety Codes. See your

Local Authority Having Jurisdiction for specific code requirements.

Alarm

Alarm Status Remote Indication - When the door is closed and

an illegal armature plate is detected, the common contact

(TB1-6) and the normally open contact (TB1-7) are activated

for the preset period of time. The alarm status relay contacts

are rated at 30VDC @ 2.0 amps maximum.

Alarm Time Setting - Refer to figure 1 (JP2). Note 15 or 30

seconds requires one jumper; 60 seconds requires no jumper

and indefinitely requires two jumpers. Unused jumpers can be

stored on a single pin.

15 Seconds 30 Seconds 60 Seconds indefinitely

LSS Remote Indication (Lock Status Sensor)

Magnet Locked - When the magnet is locked, the common

contact (TB1-3) and the normally open contact (TB1-4) are

closed. The normally closed contact (TB1-5) would be open.

Magnet Unlocked - When the magnet is unlocked, the common

contact (TB1-3) and the normally closed contact (TB1-5) are

closed. The LSS relay contacts are rated 30VDC @ 2.0 amps

maximum.

This feature can detect the quality of the locking bond between

the surface of the magnet and the armature plate. The

sensitivity of this feature is such that a foreign object with a

thickness of .007” (.18mm) is sufficient to allow the sensor to

detect a problem.

Due to the sensitivity of this feature and the necessity to

maintain a reliable locking bond, these surfaces must be kept

free of contaminating materials. Both the lock surface and

the armature plate must be cleaned periodically with a non-

abrasive cleanser. Alignment of armature plate and magnet is

required to ensure proper function of sensor.

LED Local Indication (Light Emitting Diode)

Red LED on solid – Maglock is unlocked

Green LED on solid – Maglock is locked.

Red LED blinking quickly – Illegal armature plate used; alarm

will be activated.

Each individually encoded armature plate is registered to

match it’s own electromagnetic lock.

Anti-Tamper Feature - Two screws prevent insertion of an

Allen wrench into the captive mounting screw opening on

the bottom of the lock. Fig. 3 shows their location. One

screw also secures the wiring cavity cover. The mounting

plate cannot be separated from the lock without removing

these two screws.

Inspection and Maintenance

This product and all related accessories or parts must be

inspected and maintained on a . Contacting quarterly basis

surfaces of the electromagnetic lock and armature plate

must be kept free of contaminating materials. Surfaces

must be cleaned periodically with a non-abrasive cleaner.

All mounting fasteners must be inspected on a quarterly

basis. When properly installed, the ends of the armature

plate allow a slight movement but the plate will feel secure

when grasped at the bolt. There should be no movement

to the mounting bracket or housing of the electromagnetic

lock.

For added safety, thread locking compound has been

provided for the armature plate bolt and the four captive

electromagnetic lock mounting screws.

WARNING: Improper installation, maintenance, inspection

or usage of the product or any related accessories or

parts may cause the electromagnetic lock, armature plate

and associated hardware to disengage and fall, causing

serious bodily injury and property damage.

Fig. 3 – Lock Mounting

Anti-tamper

feature screw Anti-tamper

feature and

wiring cavity

screw

Captive

mounting

screw

PLEASE DELIVER ALL INSTALLATION

INSTRUCTIONS TO THE END-USER UPON

COMPLETION OF THE INSTALLATION.

To Ensure Instant Release All switching devices must be

wired in between the DC power source and the positive

terminal of the lock in Fig 2.

Switching the negative power supply line will not allow the

lock to release immediately. RCI electromagnetic locks

contain MOV’s for surge suppression and do not require

any additional suppression to be added during installation.

The installation of diodes across the lock input terminals

will cause a delay in release.

Fig. 2 – Power Connections

SWITCH

INCORRECT

CORRECT

SWITCH

FILTERED DC SUPPLY

Specyfikacje produktu

Marka:	Dormakaba
Kategoria:	nieskategoryzowany
Model:	RCI 8310IQ

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Dormakaba RCI 8310IQ, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje nieskategoryzowany Dormakaba

Dormakaba Master Key Systems Instrukcja

31 Sierpnia 2024

Dormakaba CL700 Instrukcja

31 Sierpnia 2024

Dormakaba C500 Instrukcja

31 Sierpnia 2024

Dormakaba D800 Instrukcja

31 Sierpnia 2024

Dormakaba 9321 Instrukcja

31 Sierpnia 2024

Dormakaba 9320 Instrukcja

31 Sierpnia 2024

Dormakaba C100 Instrukcja

31 Sierpnia 2024

Dormakaba C200 Instrukcja

31 Sierpnia 2024

Dormakaba Keyscan Indala Instrukcja

31 Sierpnia 2024

Dormakaba ED250 Instrukcja

31 Sierpnia 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024

Emko EZM-9920 Instrukcja

27 Października 2024

Emko ESM-3712-H Instrukcja

27 Października 2024

Emko ATS-10 Instrukcja

27 Października 2024

Emko EAOM-11.2 Instrukcja

27 Października 2024

Emko EPM-3790 Instrukcja

27 Października 2024

Emko EPM-7790 Instrukcja

27 Października 2024

Livarno Lux IAN 108340 Instrukcja

27 Października 2024

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024