Instrukcja obsługi Dormakaba RCI 3590

Dormakaba nieskategoryzowany RCI 3590

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dormakaba RCI 3590 (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

I N S T A L L A T I O N 3590 Lock N’ Prox

Battery Powered Cabinet Lock with Built-in Proximity

IS3590-A PCN17034

R10/17GR-1

Pre-Installation Instructions

1. Prior to installing the lock into position, ensure the programming card and user cards/fobs have been initialized.

2. Test card and lock to ensure proximity reader will read through the material that the lock is to be installed on.

3. Cards/Fobs can read through as much as 1” (25mm) of non-metallic materials.

4. DO NOT INSTALL MULTIPLE LOCKS OR EXTERNAL READERS IN CLOSE PROXIMITY (Fig. 6).

5. Ensure that lock body and catch body do not contact when latch engages to ensure proper operation

Initializing the Lock

1. Press the programming button

on the back of the lock (Fig. 1).

2. Lock will make a rapid

beeping sound. Present the

programming card to lock

within three seconds.

3. Two short tones indicate the

programming card has been

initialized.

4. Multiple locks can be

programmed using the same

programming card.

Adding User Cards or

Fobs

1. Present the programming card to lock.

2. Lock will make a rapid beeping sound. Present a user card/fob to the

lock within three seconds.

3. Two tones will indicate that the user card/fob has been accepted

4. Lock can now be opened with this card/fob.

5. Additional cards/fobs can be added by repeating steps 1–4.

Deleting a User Card/Fob

1. Present the programming card to the lock.

2. Lock will make a rapid beeping sound. Present user card/fob to the

lock within three seconds.

3. Four rapid tones indicated the card/fob has been successfully

removed.

If user card/fobs have been lost all users will need to deleted and re-

enrolled.

Deleting All User Cards/Fobs

1. Present programming card to lock 16 consecutive times.

2. Sixteen beeps will sound followed by one long tone.

3. All user cards/fobs have been deleted.

Alarm Feature (Optional Alarm Pin must be used)

1. When the alarm feature is enabled the lock will detect if the door is

left ajar or forced open.

2. When the door is left ajar for more than 30 seconds the alarm will

beep for approx. 5 seconds. After the 5 seconds it will increase the

volume of sound. Closing the door or presenting a valid user card will

silence the alarm.

3. If the door is forced open the sounder will sound at full volume

immediately. To silence the alarm a valid user card must be

presented to the lock.

FCC Regulatory Statements

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the Federal Communication

Commission (FCC) rules. These limits are designed to provide

reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment causes harmful interference

to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by doing one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES

OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY

RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID

THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Fig. 1

Programming

Button

www.rutherfordcontrols.com • Phone: 1.800.265.6630 • fax: 1.800.482.9795 • e-mail: sales@rutherfordcontrols.com

Installation Instructions

1. Determine proper location for lock and fasten using provided fasteners (Fig. 1 & 2).

2. As these are RFID devices ensure minimum spacing of multiple locks and external antennas is observed to ensure proper functionality and battery life

(Fig. 1).

8" Min.

4" Min.

Fig. 1

60mm

48mm

30mm30mm

4mm

60mm

48mm

8mm

Fig. 2