Instrukcja obsługi Dolmar PS-350

Dolmar Maszyna do piłowania PS-350

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dolmar PS-350 (48 stron) w kategorii Maszyna do piłowania. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/48

Owner’s and Safety Manual

for Gasoline Chain Saws

WARNING!

Read and understand this Manual. Always follow safety precautions in the Owner’s and Safety Manual.

Improper use can cause serious injury!

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth

defects or other reproductive harm. Preserve this Manual carefully!

WARNING!

FUELS WITH MORE THAN 10% ETHANOL ARE NOT APPROVED FOR USE IN DOLMAR 2-STROKE ENGINES!

Use of alternative fuels, such as E-20 , E-85 or any fuels not meeting DOLMAR (20% ethanol) (85% ethanol)

requirements are not approved for use in DOLMAR 2-stroke gasoline engines!

USE OF ALTERNATIVE FUELS CAN CAUSE THE FOLLOWING PROBLEMS:

Poor engine performance, loss of power, overheating, fuel vapor lock, improper clutch engagement, premature

deterioration of fuel lines, premature deterioration of gaskets, premature deterioration of carburetors.

USING ALTERNATIVE FUELS AND/OR 2-STROKE OILS NOT ACCORDING TO JASO FC OR ISO-L-EGD IN

DOLMAR 2-STROKE ENGINES WILL VOID YOUR ENGINE WARRANTY!

PS-350

PS-420

EMISSIONS COMPONENT DEFECT WARRANTY COVERAGE

DOLMAR warrant to the initial retail purchaser and each subsequent owner, that this utility equipment was designed, built, and

equipped to conform at the time of initial sale to all applicable regulations of the U.S. Environmental Protection Agency (EPA), and

that the engine is free of defects in materials and workmanship which would cause this engine to fail to conform with EPA regulations

during its warranty period.

For the components listed under PARTS COVERED, the service dealer authorized by DOLMAR will, at no cost to you, make the

necessary diagnosis, repair, or replacement necessary to ensure that the engine complies with applicable U.S. EPA regulations.

EMISSION COMPONENT DEFECT WARRANTY PERIOD

The warranty period for this engine begins on the date of sale to the initial purchaser and continues for a period of 2 years.

PARTS COVERED

Listed below are the parts covered by the Emission Components Defect Warranty. Some of the parts listed below may require sche-

duled maintenance and are warranted up to the rst scheduled replacement point for that part.

Fuel Metering System Ignition System

Carburetor and internal parts Spark plug

Fuel lter, if applicable Flywheel Magneto

Throttle stopper, if applicable Ignition Coil

Choke System, if applicable

Air Induction System Miscellaneous Items Used in Above Systems

Pre lter, if exist Fuel hoses, clamps and sealing gaskets

Air lter, Air lter case, Intake manifold

Components with evaporative emissions

Fuel tank, Fuel tank cap

OBTAINING WARRANTY SERVICE

To obtain warranty service, take your engine to the nearest DOLMAR service Center authorized by DOLMAR. Bring your sales re-

ceipts indicating date of purchase for this engine. The dealer of service authorized by DOLMAR will perform the necessary repairs or

adjustments within a reasonable amount of time and furnish you with a copy of the repair order. All parts and accessories replaced

under this warranty become the property of DOLMAR.

WHAT IS NOT COVERED

• Conditions resulting from tampering, misuse, improper adjustment (unless they were made by the service dealer authorized by

DOLMAR during a warranty repair), alteration, accident, failure to use the recommended fuel and oil, or not performing required

maintenance services.

• The replacement parts used for required maintenance services.

• Consequential damages such as loss of time, inconvenience, loss of use of the engine or equipment, etc.

• Diagnosis and inspection charges that do not result in warranty-eligible service being performed.

• Any non-authorized replacement part, or malfunction of authorized parts due to use of non-authorized parts.

OWNER’S WARRANTY RESPONSIBILITIES

As the engine owner, you are responsible for the performance of the required maintenance listed in your owner’s manual.

DOLMAR recommends that you retain all receipts covering maintenance on your engine, but DOLMAR cannot deny warranty solely

for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the engine owner, you should

however be aware that DOLMAR may deny warranty coverage if your engine or a part has failed due to abuse, neglect, improper

maintenance or unapproved modications.

You are responsible for presenting your engine to the nearest service dealer authorized by DOLMAR when a problem exists.

If you have any questions regarding your warranty rights and responsibilities, you should contact the DOLMAR Warranty service

Department at 1-888-OPE-PART or info@dolmar.com for the information.

THINGS YOU SHOULD KNOW ABOUT THE EMISSION CONTROL SYSTEM WARRANTY:

MAINTENANCE AND REPAIRS

You are responsible for the proper maintenance of the engine. You should keep all receipts and maintenance records covering the

performance of regular maintenance in the event questions arise. These receipts and maintenance records should be transferred to

each subsequent owner of the engine. DOLMAR reserves the right to deny warranty coverage if the engine has not been properly

maintained. Warranty claims will not be denied, however, solely because of the lack of required maintenance or failure to keep

maintenance records.

MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY

ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A SERVICE

DEALER AUTHORIZED BY DOLMAR. THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILI-

TY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A

BEARING ON THE OUTCOME OF A WARRANTY CLAIM.

If other than the parts authorized by DOLMAR are used for maintenance replacements or for the repair of components affecting emis-

sion control, you should assure yourself that such parts are warranted by their manufacturer to be equivalent to the parts authorized

by DOLMAR in their performance and durability.

HOW TO MAKE A CLAIM

All repair qualifying under this limited warranty must be performed by a service dealer authorized by DOLMAR. In the event that any

emission-related part is found to be defective during the warranty period, you shall notify DOLMAR Warranty service Department at

1-888-OPE-PART or info@dolmar.com and you will be advised of the appropriate warranty service dealer or service providers where

the warranty repair can be performed.

The PS-350, 420 will be delivered in a protective cardboard box to prevent transport damage. Cardboard is a basic

raw material and is consequently reuseable or suitable for recycling (waste paper recycling).

WARNING !

Careless or improper use of this product can cause serious or even fatal injury.

Before operating a chain saw or other DOLMAR products it is important that you read, fully understand and

carefully follow the instructions outlined in this owners manual. Kickback may cause severe or fatal injury and

is one of many potential dangers in operating a chain saw. Kickback and other safety related precautions are

described in detail within this owners manual. Additional owners manuals are available from DOLMAR POWER

PRODUCTS, PO Box 5007, Alpharetta, GA, 30005-5007, USA, Telephone 1-888-OPE-PART or info@dolmar.

com

Contents Page

Delivery inventory .................................................... 4

Symbols ................................................................... 4

Safety precautions ..............................................5-16

Denomination of components ................................ 17

Technical data........................................................ 18

Only for Models with fastening nuts on the sprocket guard

Mounting the guide bar and saw chain ........19-26

Tightening the saw chain ..................................20

Checking the chain tension .............................. 21

Retightening the saw chain .............................. 21

Only for Models with QuickSet guide bar ..................

Mounting the guide bar and saw chain ............. 22

Tensioning the saw chain ................................. 23

Checking the chain tension .............................. 23

Retensioning the saw chain .............................. 23

Models with quick tensioner on sprocket guard ..........

Mounting the guide bar and saw chain ............. 24

Tightening the saw chain ..................................25

Checking the chain tension ..............................26

Retensioning the saw chain ..............................26

Chain brake ........................................................... 26

Engaging the chain brake ...................................... 26

Fuel / Refuelling................................................27-28

Contents Page

Chain lubrication .................................................... 29

Starting the engine ................................................ 30

Stopping the engine............................................... 30

Checking the chain brake ...................................... 31

Working in winter ................................................... 31

Adjusting the carburetor ........................................ 32

Sharpening the saw chain ................................33-34

Cleaning the brake band and sprocket interior ...... 35

Cleaning the guide bar .......................................... 35

Replacing the saw chain........................................ 36

Cleaning the air lter 37..............................................

Replacing the spark plug ....................................... 38

Checking the mufer screws ................................. 38

Replacing the starter cable .................................... 39

Replacing the return spring ................................... 39

Mounting the fan housing ...................................... 39

Cleaning the cylinder area ..................................... 40

Replacing the fuel lter .......................................... 40

Replacing / cleaning the spark arrester screen ..... 40

Instructions for daily and periodic maintenance .... 41

Service, spare parts and guarantee ...................... 42

Troubleshooting ..................................................... 43

Extract from the spare parts list ........................44-45

This product complies with: American National Standard Institute B 175.1-2000 chain saw safety standard.

Canadian Standards Association Z62.1-03 chain saw safety standard.

Z62.3-04 chain saw kickback standard.

Society of Automotive Engineers SAEJ 335-Jun 95 „Multiposition small

engine exhaust system re ignition

suppression”

The Emissions Compliance Period referred to on the emission Compliance label indicates the number of operat-

ing hours for which the engine has been shown to meet federal emissions requirements. Category C= 50 hours,

B= 125 hours, and A= 300 hours.

With the purchase of this chain saw you have chosen a German quality product. Important instructions for the

assembly and operation of this saw are given in this manual. For your own safety, we ask you to read the acci-

dent prevention instructions very carefully before putting your chain saw into operation, as incorrect handling can,

despite all precautions, lead to accidents. With a little care and attention you will have good service and lasting

satisfaction from this rst-rate product.

PS-350, PS-420

Specyfikacje produktu

Marka:	Dolmar
Kategoria:	Maszyna do piłowania
Model:	PS-350

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Dolmar PS-350, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Maszyna do piłowania Dolmar

Dolmar 153 Instrukcja

27 Września 2024

Dolmar PS7910-50 Instrukcja

20 Września 2024

Dolmar ES-173A Instrukcja

18 Września 2024

Dolmar PS3410TH-30 Instrukcja

16 Września 2024

Dolmar PS35CTLC-40 Instrukcja

15 Września 2024

Dolmar PS420C-40 Instrukcja

14 Września 2024

Dolmar 100S Instrukcja

2 Września 2024

Dolmar PS-7310 Instrukcja

30 Sierpnia 2024

Dolmar PS-350 Instrukcja

25 Sierpnia 2024

Dolmar 116 SI Instrukcja

20 Sierpnia 2024

Instrukcje Maszyna do piłowania

Najnowsze instrukcje dla Maszyna do piłowania

Makita 5603 Instrukcja

15 Października 2024

MSW -TAS287 Instrukcja

15 Października 2024

MSW T-SAW300 Instrukcja

15 Października 2024

Black & Decker KS650 Instrukcja

14 Października 2024

Black & Decker GKC3630L20 Instrukcja

14 Października 2024

Ferm FKS-165 Instrukcja

14 Października 2024

Royal Catering RCBS-1650 Instrukcja

14 Października 2024

Royal Catering RCBS-1650.1ECO Instrukcja

14 Października 2024

Husqvarna 365H Instrukcja

13 Października 2024

Makita DJV181Z Instrukcja

12 Października 2024