Instrukcja obsługi DJI FPV Air Unit

DJI warkot FPV Air Unit

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DJI FPV Air Unit (7 stron) w kategorii warkot. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/7
2019.05v1.0
DJI FPV AIR UNIT
Quick Start Guide
快速入门指南
快速入門指南
クイックスタートガイド
스타트 가이드
Kurzanleitung
Guía de inicio rápido
Guide de démarrage rapide
Guida rapida
Snelstartgids
Guia de início rápido
Guia de Início Rápido
Краткое руководство пользователя
2
EN
Disclaimer
Congratulations on purchasing your new DJI™ product. The
information in this document affects your safety and your legal
rights and responsibilities. Read this entire document carefully
to ensure proper conguration before use. Failure to read and
follow instructions and warnings in this document may result in
serious injury to yourself or others, damage to your DJI product,
or damage to other objects in the vicinity. This document and
all other collateral documents are subject to change at the sole
discretion of DJI. Visit www.dji.com for the latest information for
this product.
By using this product, you hereby signify that you have read
this disclaimer and warning carefully and that you understand
and agree to abide by the terms and conditions herein. You
agree that you are solely responsible for your own conduct
while using this product, and for any consequences thereof.
You agree to use this product only for purposes that are
proper and in accordance with all applicable laws, rules, and
regulations, and all terms, precautions, practices, policies, and
guidelines DJI has made and may make available.
DJI accepts no liability for damage, injury, or any legal
responsibility incurred directly or indirectly from the use of
this product. The user shall observe safe and lawful practices
including, but not limited to, those set forth in this document.
Notwithstanding the above, you r statu to ry rights under
applicable national le gislation are n ot affected by this
disclaimer.
DJI is a trademark of SZ DJI TECHNOLOGY CO., LTD.
(abbreviated as “DJI”) and its affiliated companies. Names
of products, brands, etc., appearing in this document are
trademarks or registered trademarks of their respective owner
companies. This product and document are copyrighted by
DJI with all rights reserved. No part of this product or document
shall be reproduced in any form without prior written consent of
or authorization from DJI.
Introduction
The DJI FPV Air Unit is an advanced video transmission module
that supports a 5.8 GHz digital video signal and 720p 120fps
image transmission, with a transmission range of up to 4 km
and a minimum end-to-end latency within 28 ms*. The air
unit can be mounted on a racing drone and used with DJI
FPV Goggles or a remote controller to transmit video, control
signals, and ight controller information wirelessly.
1. MMCX Antenna Ports
2. 3-in-1 Port
3. USB-C Port
4. microSD Card Slot
1
2
3
4
5 6
7
5. Link Button
6. Linking Status Indicator
7. Camera
* The end-to-end latency is the total time from camera input to screen
display. The device is able to reach its minimum latency and
maximum transmission distance (FCC) in a wide open area with no
electromagnetic interference.
3
Connection
Refer to the illustration below to mount and connect the air unit to
a racing drone.
RED: Power (7.4-17.6 V)
BLACK: Power GND
WHITE: UART RX (Connects to Flight Controller
OSD TX, 0-3.3 V)
GRAY: UART TX (Connects to Flight Controller OSD
RX, 0-3.3 V)
BROWN: Signal GND
YELLOW: DJI HDL (Connects to Flight Controller
S.Bus, 0-3.3 V)
An electric soldering iron and soldering tin are required
for connection. Make sure that there are no short circuits
or open circuits when soldering the cables.
There are up to eight channels for the air unit depending
on the region (FCC: eight, CE/SRRC: four, MIC: three).
Each channel has a bandwidth of 20 MHz. The public
channel is 8, which is the default channel when the
equipment is powered on. The channel can be changed
manually to avoid interference from other devices.
The air unit may become hot during or after operation.
DO NOT touch the air unit before it cools down.
DO NOT use the air unit for an extended period when
the temperature is high or there is poor ventilation.
Otherwise, the air unit may overheat and enter low-
power mode which will affect its performance. If the
air unit enters low-power mode, restart it or wait for it
to cool down and it will automatically return to normal.
Keep the antennas of the air unit at least 40 mm apart.
Keep the air unit away from metal objects or carbon
ber frames. Make sure to choose a position where
the transmission will not be blocked during ight.
Activation
When powered on, connected the air unit to your computer and
run DJI ASSISTANTTM 2 for activation.
Download DJI Assistant 2 at https://www.dji.com/fpv/downloads
Linking
The air unit support three linking methods: A, B, and A+B
(Must link A before B).
1. Power on the air unit and the DJI FPV Goggles.
2. Press the link button on the air unit and the goggles.*
3. The linking status indicator of the air unit turns solid green.
The goggles stop beeping when successfully linked and the
video display is normal.
3-in-1 Cable (Power, DJI HDL, UART)
A.


Specyfikacje produktu

Marka: DJI
Kategoria: warkot
Model: FPV Air Unit

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z DJI FPV Air Unit, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje warkot DJI

Instrukcje warkot

Najnowsze instrukcje dla warkot

Xiaomi

Xiaomi FIMI X8 Mini Instrukcja

9 Października 2024
Hobbywing

Hobbywing XRotor X8 Instrukcja

9 Października 2024
Denver

Denver PSQ-20008 MK2 Instrukcja

9 Października 2024
Denver

Denver LQI-105 Instrukcja

9 Października 2024
Kogan

Kogan Viper-X 3 Instrukcja

8 Października 2024
Kogan

Kogan Zenith Instrukcja

8 Października 2024
Jamara

Jamara Payload Altitude Instrukcja

8 Października 2024
Carrera

Carrera RC Video Next Instrukcja

8 Października 2024
Syma

Syma X8HW Instrukcja

7 Października 2024