Instrukcja obsługi Dimplex XLE100

Dimplex Podgrzewacz XLE100

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dimplex XLE100 (38 stron) w kategorii Podgrzewacz. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/38

08/80271/0 ISSUE: 5 Series: A

Dimplex XLE Series Heater

Models: XLE050 / XLE070 / XLE100

XLE125 / XLE150

These instructions should be read carefully and

retained for future use. Note also the information

presented on the appliance.

INSTRUCTION MANUAL

Installation and Operating

IMPORTANT

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR

FUTURE REFERENCE. Note also the information presented on the appliance

IMPORTANT SAFETY ADVICE

When using electrical heaters, basic precautions should always be followed to reduce

the risk of ﬁre, electrical shock, and injury to persons, including the following:

IMPORTANT – The wall bracket supplied with the heater must be used.

IMPORTANT – All packaging should be disposed of in an appropriate manner.

OVERHEATING WARNING

WARNING - In order to avoid overheating, do not cover or obstruct the heater. Do not

place material or garments on the heater, or obstruct the air circulation around the

heater, for instance by curtains or furniture, as this could cause overheating and a ﬁre

risk. NEVER cover or obstruct in any way the heat outlet slots at the top of the heater

or the air outlet slots in the base of the heater.

WARNING - THE SURFACES ON THIS HEATER CAN BE HOT.

The heater carries a warning ‘DO NOT COVER’ to alert the user to the risk of ﬁre that

exists if the heater is accidentally covered.

CAUTION - Some parts of this product can become very hot and cause burns.

Particular attention has to be given where children and vulnerable people are present.

For your safety this heater is ﬁtted with a thermal cut-out. In the event that the product

overheats for some reason, the cut-out prevents excessive temperatures on the product

by cutting the power to the heater. Once the heater has cooled down, it will reset

automatically, it will continue to cycle on and o automatically until the reason for

overheating is removed.

The display screen may ﬂash red to indicate the product has overheated. To reset the

display, remove the obstruction and hold Enter for 10 seconds.

SUITABLE APPLICATIONS

WARNING - This heater is suitable for normal domestic household purposes and should not

be used in any other type of environment. This product should only be used in the country

where it was purchased from by a recognised commercial retailer. Do not use outdoors.

SERVICING AND REPAIRS

WARNING - Servicing and product repairs should only be undertaken by the

manufacturers approved service agent or a similarly trained or qualiﬁed person, using

only exact manufacturer approved spare parts.

PLEASE NOTE: Household dust, lit cigarettes, candles and oil burners, combined with

the convection eect of electric heaters can cause signiﬁcant soot deposits to build

up on the surface directly above and to the sides of the heater. This is not a fault of the

heater. Extensive burning of candles or smoking in the operating environment of this

product can produce heavy discolouration within a few months of use.

CAUTION

FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/OR

DAMAGE AND MAY INVALIDATE YOUR GUARANTEE

OPERATING WARNINGS

IMPORTANT: Remember to observe all safety warnings and precautions when operating

the heater on the automatic or timer modes, either attended or unattended since a ﬁre

risk exists when the heater is accidentally covered or obstructed.

Mains cables are not provided with this heater.

CAUTION: Do not use if either of the heater’s mains power leads become damaged. If

the supply cord is damaged it must be replaced by the installer or an approved Dimplex

service partner.

Curtains must not come to within 250mm of the top of the heater.

Do not sit or stand on the heater.

Do not place objects in contact with the heater.

To maintain stability, it is essential that the heater is placed on a level surface and care

should be taken to avoid irregular surfaces, such as may result from carpets or tiled

surrounds partially protruding under the heater.

ELECTRICAL INSTALLATION

The installation of the heater should be carried out by trained personnel.

WARNING - Minimum clearances and IP zone requirements must be adhered to in

accordance with the current wiring regulations.

WARNING - The electrical installation of this heater must be carried out by a suitably

qualiﬁed or trained electrician, and be in strict accordance with current wiring Regulations.

The peak supply must be connected via a switched fused spur with a fuse rated suitably

for the appliances ﬂex, the o-peak supply , via a 20A double pole switch. Failure to

follow these instructions will mean that the manufacturer’s instructions have not been

adhered to. THERE ARE NO EXCEPTIONS.

• This heater must be earthed

• Not suitable for connection via a plug top

• Do not locate the heater immediately above or below a ﬁxed electrical point i.e. socket

outlet.

This appliance is intended for installation to a single phase supply only and is not suitable

for connection to 3 phase supplies.

The heater is not ﬁtted with a mains cable, this should be ﬁtted by the installer. Cable

type (minimum size) H05VV-F 1.5mm² three core for peak and 2.5mm² three core for

o-peak for connection to the ﬁxed wiring of the premises through suitable isolation

devices positioned adjacent to the heater. The supply circuits to the heater must

incorporate a double pole isolating switch having a contact separation of at least 3mm.

In installation the supply cord must be cut to the appropriate length for the electrical

connection point. Excess cable should not be inserted or stored behind the heater.

If, during reassembly of the heater, a part of the thermal insulation shows damage or

deterioration, it should be replaced by an identical part.

WARNING: All electrical connections to the terminal block must be secure to prevent

risk of ignition. Tighten to 0.5 Nm.

Specyfikacje produktu

Marka:	Dimplex
Kategoria:	Podgrzewacz
Model:	XLE100
Kolor produktu:	Czarny
Wbudowane głośniki:	Nie
Wyjścia słuchawkowe:	1
Długość przekątnej ekranu:	21.5 "
Rozdzielczość:	1920 x 1080 px
Współczynnik kontrastu (typowy):	1000:1
Ekran dotykowy:	Nie
Pobór mocy:	24 W
Ilość portów HDMI:	1
Jasność wyświetlacza (typowa):	250 cd/m²
Kąt widzenia (poziomy):	170 °
Kąt widzenia (pionowy):	160 °
Czas odpowiedzi (typowy):	5 ms
Rozmiar plamki:	0.248 x 0.248 mm
Częstotliwość odświeżania poziomego:	24 - 83 kHz
Częstotliwość odświeżania pionowego:	50 - 76 Hz
Wbudowana kamera/aparat:	Nie
Interfejs do montażu panelu:	100 x 100 mm
Liczba portów VGA (D-Sub):	1
HDCP:	Nie
Szerokość (bez podstawy):	516.2 mm
Głębokość (bez podstawy):	173 mm
Wysokość (bez podstawy):	387.1 mm
Waga (bez podstawy):	4000 g
Wbudowany tuner tv:	Nie