Instrukcja obsługi Dimplex DEUF2

Dimplex Podgrzewacz DEUF2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dimplex DEUF2 (4 stron) w kategorii Podgrzewacz. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
The product complies with the European Safety Standards EN60335:2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014:1,
EN55014:2, EN61000:3-2 and EN61000:3-3 which cover the essential requirements of EMC Directive 2014/30/EU and the LVD Directive 2014/35/EU.
08/51929/0 Issue 6
DEUF2
Installation and Operating Instructions
As with all portable heang appliances: This product is suitable only for well insulated spaces or occasional use.
Fan Heaters
Model(s) : DEUF2
Dimensions
(millimetres)
IMPORTANT SAFETY ADVICE
READ THESE INSTRUCTIONS BEFORE USE.
DO NOT use the heater on deep pile carpets or
the long hair type of rugs, or less than 750mm
(30”) away from any overhanging surface. Keep
combustible materials such as drapes and other
furnishings clear from the front, sides and rear of
the heater. Do not use heater to dry your laundry.
DO NOT use the heater in the immediate
surroundings of a bath, a shower or a swimming
pool.
DO NOT place the heater directly below a xed
socket outlet.
The socket-outlet must be accessible at all times
to enable the mains plug to be disconnected as
quickly as possible.
DO NOT COVER or obstruct the air inlet and
outlet openings in any way.
The heater must be on a at stable surface when
in use.
DO NOT operate the heater with the mains lead
overhanging the front outlet grille.
The heater carries the warning symbol to
indicate that it must not be covered.
WARNING: In order to avoid overheating do not
cover the heater.
The instruction leaet belongs to the appliance
and must be kept in a safe place. If changing
owners, the leaet must be surrendered to the
new owner.
WARNING: To avoid danger of suffocation please
remove all packaging materials particularly plastic
and EPS and keep these away from vulnerable
people,children and babies.
WARNING: To avoid the risk of accidental
strangulation from the supply cord all children and
vulnerable people must be supervised when in the
vicinity of the product whether it is working or not.
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
IMPORTANT: If the mains lead of this appliance is
damaged, it must be replaced by the manufacturer
or its service agent or a similarly qualied person
in order to avoid a hazard.
WARNING: In order to avoid a hazard due to
inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through an
external switching device, such as a timer, or
connected to a circuit that is regularly switched
on and off by the utility.
This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience or knowledge if they have been given
supervision or instruction concerning the use of
the appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
Children of less than 3 years should be kept away
unless continuously supervised. Children aged
from 3 years and less than 8 years shall only
switch on/off the appliance provided that it has
been placed or installed in its intended normal
operating position and they have been given
supervision or instruction concerning the use of
the appliance in a safe way and understand the
hazards involved. Children aged from 3 years and
less than 8 years shall not plug in, regulate and
clean the appliance or perform user maintenance.
CAUTION: Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.
Avoid use of an extension cord because the
extension cord may overheat and cause risk of
re.
Model(s) Specication
DEUF2 2.0kW Thermostat & Switch
H W D
241 212 166
Fig. 1
3
4
1
2
Electrical connection
This heater must be used on an supply only and the voltage A.C.~
marked on the heater must correspond to the supply voltage. This
heater is tted with a plug incorporating a 13 amp fuse. When
replacing the fuse, a 13 amp fuse approved by ASTA to BS 1362
must be used.
If the plug is not suitable for the socket outlets in your home, the
plug must be cut off and an appropriate one tted. A plug cut off
from a mains lead will give a shock hazard if inserted into a 13
amp socket elsewhere in the house. To avoid this, it should be
disposed of immediately.
NOTE: The fuse cover of a non-rewirable plug must be retted
when changing the fuse. Should the cover become lost, the plug
must not be used until the correct replacement fuse cover is
obtained from your supplier or by contacting our customer helpline.
IMPORTANT : The wires in this mains lead are coloured in
accordance with the following code :
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead may not correspond
with the coloured markings in your plug, proceed as follows :
Connect the wire to the terminal marked ‘ ’ or coloured BROWN L
RED BLUE. Connect the wire to the terminal marked ‘N’ or
coloured .BLACK Note : ‘L’ or ‘ ’ must not be connected to N
the EARTH terminal marked ‘E’ or ‘ ’ or coloured or GREEN
GREEN AND YELLOW.
If in doubt, consult your electrician.
Using the Heater
Main Elements - See Fig 1.
Heat Control - see Fig. 1.2
Thermostat Control - see Fig. 1.3
The heat output is controlled by the
thermostat, according to the room
temperature.
Turn the thermostat knob fully
clockwise to maximum setting initially.
When the room is warm enough,
reduce the setting slowly until the
heater just clicks off.
The heater will now cycle on and off to maintain your
selected room temperature. An audible click may be heard
when the thermostat operates - this is normal.
Note : If the heater does not come on when the thermostat is
at a low setting, this is normally because the room is warmer
than the thermostat setting and is not a fault.
* When the heat control is set to ‘ ’ for cool blow, set the
thermostat control to maximum.
Position ‘ ’ will turn the heater on and off to maintain a
temperature of approximately 5°C.
Safety - overheat protection
For your safety, this appliance is tted with a thermal cut-out.
In the event that the product overheats, the cut-out switches
the heater off automatically. To bring the heater back into
operation, remove the cause of overheating, then turn off
the electrical supply to the heater for a few minutes.
When the heater has cooled sufciently reconnect and
switch on the heater.
If the cut-out operates repeatedly, contact your supplier.
Cleaning
WARNING ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
Do not use detergents, abrasive cleaning powders or polish
of any kind on the heater.
Wipe with a dry cloth to remove dust and a damp cloth (not
wet) to clean off stains. Be careful not to allow moisture
into the heater.
Ensure that dust or uff does not accumulate inside the
heater as this could lead to overheating of the element.
Use a vacuum cleaner to remove any uff which does
accumulate.
Recycling
For electrical products sold within the
European Community.
At the end of the electrical products useful life
it should not be disposed of with household
waste. Please recycle where facilities exist.
Check with your Local Authority or retailer
for recycling advice in your country.
ModelIdentier(s): DEUF2
Heat output
Nominal heat output Pnom 2.0 kW
Minimum heat output (indicative) Pmin 0.8 kW
Maximum continuous heat output Pmax,c 2.0 kW
Auxiliary electricity Consumption
At nominal heat output 0.0elmax kW
At minimum heat output elmin 0.0 kW
In standby mode elSB 0.0 kW
Type of heat output/ room temperature control
Mechanical thermostat room temperature control Yes
Contact details
GDHV
Millbrook House, Grange Drive, Hedge
End, Southampton.
SO30 2DF
1. Power Indicator Light
2. Thermostat Control Knob
3. Switch Knob
4. Air Outlet
- Off
- Cool Blow*
- Half Heat
- Full Heat
Fig. 1.2
Fig. 1.3
*

Specyfikacje produktu

Marka: Dimplex
Kategoria: Podgrzewacz
Model: DEUF2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Dimplex DEUF2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Podgrzewacz Dimplex

Dimplex

Dimplex DHOC24 Instrukcja

11 Lutego 2025
Dimplex

Dimplex DHCHR20D Instrukcja

11 Lutego 2025
Dimplex

Dimplex DHCHR20M Instrukcja

11 Lutego 2025
Dimplex

Dimplex DX 521 Instrukcja

13 Stycznia 2025
Dimplex

Dimplex DTD4T Instrukcja

30 Grudnia 2025
Dimplex

Dimplex ECOT4FT Instrukcja

8 Października 2024
Dimplex

Dimplex VFM60HY Instrukcja

5 Października 2024
Dimplex

Dimplex Huxley Revillusion HXY20-AU Instrukcja

3 Października 2024
Dimplex

Dimplex Strata Revillusion STA20-AU Instrukcja

3 Października 2024
Dimplex

Dimplex SILVERTON Instrukcja

2 Października 2024

Instrukcje Podgrzewacz

Najnowsze instrukcje dla Podgrzewacz

Ambiano

Ambiano HFE-1 Instrukcja

22 Marca 2025
Fire Sense

Fire Sense 62555 Instrukcja

11 Marca 2025
Listo

Listo LRS4263b Instrukcja

27 Lutego 2025
Nobo

Nobo NTL4R 15 Instrukcja

27 Lutego 2025
Nobo

Nobo NTL4R 20 Instrukcja

27 Lutego 2025
Nobo

Nobo NTL4R 24 Instrukcja

27 Lutego 2025
Nobo

Nobo NTL4R 10 Instrukcja

27 Lutego 2025
Honeywell

Honeywell Two Position HHF250 Instrukcja

27 Lutego 2025
Honeywell

Honeywell UberHeat Plus HCE220 Instrukcja

27 Lutego 2025
Honeywell

Honeywell UberHeat 5 HCE210 Instrukcja

27 Lutego 2025