Instrukcja obsługi DeWalt DW925

DeWalt Wiertarka DW925

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DeWalt DW925 (25 stron) w kategorii Wiertarka. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/25

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

DW925

Cordless Adjustable Clutch Driver/Drill

Perceuse-tournevis sans fil à embrayage réglable

Taladro/Destornillador Inalámbrico con Embrague Ajustable

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y

PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D EWALT TOOL,

CALL US TOLL FREE AT:

1-800-4-DEWALT (1-800-433-9258)

General Safety Instructions for All Battery Operated

Tools

WARNING! Read and understand all instructions. Failure to follow all instructions listed below,

may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flam-

mable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

• Keep bystanders, children, and visitors away while operating a power tool. Distractions can

cause you to lose control.

ELECTRICAL SAFETY

• Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from heat, oil,

sharp edges or moving parts. Replace damaged cords immediately. Damaged cords may create

a fire.

• A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery. A charger that may be suitable for

one type of battery may create a risk of fire when used with another battery.

• Use battery operated tool only with specifically designated battery pack. Use of any other

batteries may create a risk of fire.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment

of inattention while operating power tools may result in serious personal injury,

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, cloth-

ing , and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in

moving parts.

• Avoid accidental starting. Be sure switch is in the locked or off position before inserting battery

pack. Carrying tools with your finger on the switch or inserting the battery pack into a tool with the

switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left

attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and balance

enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat,

or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support the workpiece to a stable plat-

form. Holding the work by hand or against your body is unstable and may lead to loss of control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the job bet-

ter and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the

switch is dangerous and must be repaired.

• Disconnect battery pack from tool or place the switch in the locked or off positionbefore

making any adjustments, changing accessories, or storing the tool. Such preventative safe-

ty measures reduce the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are dangerous

in the hands of untrained users.

• When battery pack is not in use, keep it away from metal objects like: paper clips, coins, keys,

nails, screws, or other small metal objects that can make a connection from one terminal to the

other. Shorting the battery terminals together may cause sparks, burns, or a fire.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with

sharp cutting edges are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any other con-

dition that may affect the tools operation. If damaged, have the tool serviced before using.

Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may create a risk of injury when used on another

tool.

SERVICE

• Tool service must be performed only by qualified repair personnel. Service or maintenance

performed by unqualified personnel may result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in the

Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance

Instructions may create a risk of shock or injury.

Additional Specific Safety Instructions

• Hold tool by insulated gripping surfaces when performing an operation where the cutting

tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts

of the tool “live” and shock the operator.

WARNING: Use of this tool can generate dust containing chemicals known to cause can-

cer, birth defects or other reproductive harm. Use appropriate respiratory protection.

• When working on a ladder or on scaffolding be sure to lay the tool down on its side

when not in use. Some tools with large battery packs will stand upright but may be easily

knocked over.

• The label on your tool may include the following symbols.

V ..............volts A ................amperes

Hz ............hertz W ..............watts

min ..........minutes ............alternating current

..........direct current no ..............no load speed

............Class II ..............earthing terminal

................Construction ..............safety alert symbo

.../min ......revolutions per minute

Important Safety Instructions for Battery Chargers

• This manual contains important safety and operating instructions.

• Before using charger, read all instructions and cautionary markings on (1) charger, (2) bat-

tery pack, and (3) product using battery pack.

• DANGER: 120 volts present at charging terminals. Do not probe with conductive objects.

Danger of electric shock or electrocution.

• DANGER: If battery pack case is cracked or damaged, do not insert into charger. Danger

of electric shock or electrocution.

• The charger and battery pack are specifically designed to work together. DO NOT attempt

to charge the battery pack with any chargers other than the ones in this manual.

• Do not expose charger to rain or snow.

• These chargers are not intended for any uses other than charging DeWalt rechargeable bat-

teries. Any other uses may result in risk of fire, electric shock or electrocution.

• To reduce risk of damage to electric plug and cord, pull by plug rather than cord when dis-

connecting charger.

• Make sure cord is located so that it will not be stepped on, tripped over, or otherwise sub-

jected to damage or stress.

• An extension cord should not be used unless absolutely necessary. Use of improper exten-

sion cord could result in risk of fire, electric shock, or electrocution.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for safe-

ty. The smaller the gauge number of the wire, the greater the capacity of the cable, that is

16 gauge has more capacity than 18 gauge. When using more than one extension to make

up the total length, be sure each individual extension contains at least the minimum wire

size.

RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS

Total Extension Cord Length (feet)

25 50 75 100 125 150 175

Wire Gauge

18 18 16 16 14 14 12

• The charger is ventilated through slots in the top and the bottom of the housing. Do not

place any object on top of charger or place the charger on a soft surface that might block

the ventilation slots and result in excessive internal heat. Place the charger in a position

away from any heat source.

• Do not operate charger with damaged cord or plug — have them replaced immediately.

• Do not operate charger if it has received a sharp blow, been dropped, or otherwise dam-

aged in any way; take it to an authorized service center.

• Do not disassemble charger; take it to an authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.

• To reduce risk of electric shock, unplug charger from outlet before attempting any cleaning.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• DO NOT store or use the tool and battery pack in locations where the temperature may

reach or exceed 105°F (such as outside sheds or metal buildings in summer).

• The charger is designed to operate on standard household electrical power (120 Volts). Do

not attempt to use it on any other voltage!

Important Safety Instructions for Battery Packs

The battery pack is not fully charged out of the carton! First read the safety instructions below.

Then follow charging notes and procedures.

READ ALL INSTRUCTIONS.

• Do not incinerate the battery pack even if it is severely damaged or is completely worn

out.The battery pack can explode in a fire.

• A small leakage of liquid from the battery pack cells may occur under extreme usage or tem-

perature conditions. This does not indicate a failure. However, if the outer seal is broken and

this leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If battery liquid gets into your eyes, flush them with clean water for a minimum of 10 min-

utes and seek immediate medical attention. (Medical note: The liquid is 25-35% solution of

potassium hydroxide.)

• Never attempt to open the battery pack for any reason. If the plastic housing of the battery

pack breaks or cracks, immediately discontinue use and do not recharge.

• Do not carry extra battery packs in aprons, pockets, or tool boxes along with other metal

objects. Battery pack could be short circuited causing damage to the battery pack and pos-

sibly causing severe burns or fire.

• Charge the battery packs only in DeWalt chargers.

• NOTE: Review and observe all of the “Important Charging Notes” in the charger instruction

section of this manual.

• NOTE: The batteries in your battery pack are the nickel–cadmium type. Cadmium is con-

sidered to be a toxic material by the Environmental Protection Agency. Before disposing of

damaged or worn out Nickel–Cadmium battery packs, check with your state Environmental

Protection Agency to find out about special restrictions on the disposal of these battery

packs or return them to a DeWALT certified service center for recycling.

Battery Packs

Your tool uses a 7.2, Volt D WALT battery pack. When ordering replacement battery packs,E

be sure to include catalog number and voltage.

D EWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

Questions? See us in the World Wide Web at www.dewalt.com

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel-

cadmium battery (or battery pack) indicates that the costs to recycle the battery

(or battery pack) at the end of its useful life have already been paid by DeWalt.

In some areas, it is illegal to place spent nickel-cadmium batteries in the trash or

municipal solid waste stream and the RBRC program provides an environmen-

tally conscious alternative.

RBRC in cooperation with DeWalt and other battery users, has established programs in the

United States to facilitate the collection of spent nickel-cadmium batteries. Help protect our

environment and conserve natural resources by returning the spent nickel-cadmium battery to

an authorized DeWalt service center or to your local retailer for recycling. You may also con-

tact your local recycling center for information on where to drop off the spent battery.

Chargers

Your battery can be charged in DEWALT 1 Hour Chargers or 15 Minute Chargers. Be sure to

read all safety instructions before using your charger.

Charging Procedure

These chargers require no adjustment and are designed to be as easy as possible to oper-

ate. Simply place your battery pack into the receptacle of a plugged in charger (FIG.1) and it

will automatically charge the pack.

1 HOUR CHARGERS

1. Plug the charger into an appropriate AC power outlet.

2. Insert the battery pack into the charger, as shown in FIG.1, making sure the pack is fully

seated in the charger. The red (charging) light will blink continuously indicating that the

charging process has started.

3. The battery pack will be fully charged in about 1 hour. The completion of charge will be indi-

cated by the red light remaining ON continuously. The pack is fully charged and may be

used at this time or left in the charger.

15 MINUTE CHARGERS

1. Plug the charger into an appropriate AC power outlet. The charger will beep twice, the red

light will blink and go off.

2. Insert the battery pack into the charger, as shown in FIG. 1, making sure the pack is fully

seated in the charger. The red light will blink and the charger will beep once indicating the

charging process has started.

3. The battery pack will be fully charged in less than 15 minutes under most conditions. This

will be indicated by the red light remaining ON and 3 beeps. The pack is fully charged and

may be used at this time or left in the charger.

Weak Battery Packs: (15 Minute Chargers). The charger can also detect a weak battery.

Such batteries are still usable but should not be expected to perform as much work. In such

cases, about 10 seconds after battery insertion, the charger will beep rapidly 8 times to indi-

cate a weak battery condition. The charger will then go on to charge the battery to the high-

est capacity possible.

Leaving the battery pack in the charger: When the red light remains ON, the charger has

switched to its "equalize charge" mode which lasts approximately 4 hours, after which the

charger will switch to "maintenance charge" mode. The battery pack can be removed at any

time during these charge cycles, but will only be fully charged if the red light is continuously

ON. The charger and battery pack can be left connected with the red light glowing indefinite-

ly. The charger will keep the battery pack fresh and fully charged. A battery pack will slowly

lose its charge when kept out of the charger. If the battery pack has not been kept on main-

tenance charge, it may need to be recharged before use. A battery pack may also slowly lose

its charge if left in a charger that is not plugged into an appropriate AC source.

Trouble Indicators: These chargers are designed to detect certain problems that can arise

with battery packs which would be indicated by the red light flashing at a fast rate (and con-

tinuous beeping for 15 Minute Chargers). If this occurs, re-insert battery pack. If problem per-

sists, try a different battery pack to determine if the charger is OK. If the new pack charges

correctly, then the original pack is defective and should be returned to a service center for

recycling. If the new battery pack elicits the same trouble indication as the original, have

charger tested at an authorized service center.

PROBLEM POWER LINE

If your charger has a Problem Power Line indicator: When the charger ‘is used with some

portable power sources such as generators or sources that convert DC to AC, the charger may

temporarily suspend operation, flashing the red light with two fast blinks followed by a

pause. This indicates the power source is out of limits.

HOT PACK DELAY

If your charger has a Hot Pack Delay feature: When the charger detects a battery that is hot, it

automatically starts a Hot Pack Delay, suspending charging until the battery has cooled. After

the battery has cooled, the charger automatically switches to the Pack Charging mode. This

feature ensures maximum battery life. The red light flashes long, then short while in the Hot

Pack Delay mode.

Installing and Removing the Battery Pack

NOTE: Make sure your battery pack is fully charged.

To install the battery pack into the tool handle, align the base of the tool with the notch

inside the tool’s handle (FIG. 2) and slide the battery pack firmly into the handle until you hear

the lock snap into place as shown in FIG. 3.

To remove the battery pack from the tool, press the release buttons and firmly pull the bat-

tery pack out of the tool handle. Insert it into the charger as described in the charger section

of this manual.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when the

air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack

in an air temperature below +40°F(+4.5°C), or above +105°F (+40.5°C). This is important

and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a normal

condition, and does not indicate a problem.

3. The 15 minute charger has an internal temperature limit that, when exceeded, will tem-

porarily stop the full charge current. This is indicated by the yellow light being ON. The nor-

mal charge cycle will resume when the temperature falls below the preset limit and will be

indicated by the yellow light turning OFF. The charge time may be extended beyond the

normal 15 minutes. Use the charger in normal room temperatures whenever possible. To

prevent overheating, do not cover the charger and do not charge battery packs in direct

sunlight or near heat sources.

4. If the battery pack does not charge properly — (1) Check current at receptacle by plugging

in a lamp or other appliance, (2) Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights. (3) Move charger and battery pack to a

location where the surrounding air temperature is approximately 65°F - 75°F (18°- 24°C).

(4) If charging problems persist, take or send the tool, battery pack and charger to your

local service center.

5. The battery pack should be recharged when it fails to produce sufficient power on jobs

which were easily done previously. DO NOT CONTINUE to use under these conditions.

Follow the charging procedure. You may also charge a partially used pack whenever you

desire with no adverse affect on the battery pack.

6. Under certain conditions, with the charger plugged in to the power supply, the exposed

charging contacts inside the charger can be shorted by foreign material. Foreign materials

of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup

of metallic particles should be kept away from charger cavities. Always unplug the charg-

er from the power supply when there is no battery pack in the cavity. Unplug charger before

attempting to clean.

7. Do not freeze or immerse charger in water or any other liquid.

8. WARNING: Don't allow any liquid to get inside charger. Electric shock may result. To

facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack

in a warm environment such as in a metal shed, or an uninsulated trailer.

9. CAUTION: Never attempt to open the battery pack for any reason. If the plastic housing

of the battery pack breaks or cracks, return to a service center for recycling.

Important!

This product is not user servicable. There are no user servicable parts inside the charger.

Servicing at an authorized service center is required to avoid damage to static sensitive inter-

nal components.

READ ALL OF THE INSTRUCTIONS IN THE BATTERY CHARGER SECTION OF THIS

MANUAL BEFORE ATTEMPTING TO CHARGE THE BATTERY PACK FOR YOUR TOOL.

Always use correct battery pack (pack supplied with tool or replacement pack exactly like it.)

Never install any other battery pack. It will ruin your tool and may create a hazardous condi-

tion.

Variable Speed Switch (Fig. 4)

To turn the tool on, squeeze the trigger switch (A). To turn the tool off, release the trigger

switch. Your tool is equipped with a brake. The chuck will stop as soon as the trigger switch

is fully released.

The variable speed switch enables you to select the best speed for a particular application.

The farther you squeeze the trigger, the faster the tool will operate. Use lower speeds for start-

ing holes without a centerpunch, drilling in metals or plastics, driving screws and drilling

ceramics. Higher speeds are better for drilling in wood, wood compositions and for using abra-

sive and polishing accessories. For maximum tool life, use variable speed only for starting

holes or fasteners.

NOTE: Continuous use in variable speed range is not recommended. It may damage the

switch and should be avoided.

Forward/Reverse Control Button (Fig. 4)

A forward/reverse control button (B) determines the direction of the tool and also serves as a

lock off button. To select forward rotation, release the trigger switch and depress the for-

ward/reverse control button on the right side of the tool.To select reverse, depress the for-

ward/reverse control button on the left side of the tool. The center position of the control but-

ton locks the tool in the off position. When changing the position of the control button, be sure

the trigger is released. The first time the tool is run after changing the direction of rota-NOTE:

tion, you may hear a click on start up. This is normal and does not indicate a problem.

Torque Adjustment Collar (Fig. 5)

The torque adjustment collar (A) is clearly marked with numbers and a drill bit symbol.The col-

lar should be rotated until the desired setting is located at the top of the tool. Locators are pro-

vided in the collar to eliminate the guess work when selecting fastening torque. The higher the

number on the collar, the higher the torque and the larger the fastener which can be driven.

To lock the clutch for drilling operations, move to the drill bit position.

NOTE: When using the Drill/Driver for drilling holes, be sure that the Torque Adjusting Collar

is set so the figure of the drill is aligned with the arrow on the top of the tool. Failure to do this

will allow the clutch to slip while attempting to drill

Keyless Chuck (Fig. 6)

Your tool features a keyless chuck for greater convenience. To insert a drill bit or other acces-

sory, follow the steps listed below.

1. Lock the trigger switch in the off position as described earlier.

2. Grasp the rear half of the chuck with one hand and use your other hand to rotate the front

half counterclockwise, as shown in FIG 6. Rotate far enough so that the chuck opens suffi-

ciently to accept the desired accessory.

3. Insert the bit or other accessory about 3/4” into the chuck and tighten securely by holding the

rear half of the chuck and rotating the front portion in the clockwise direction.

To release the accessory, repeat step 2 listed above.

WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front

part of the chuck and turning the tool on. Damage to the chuck and personal injury may result.

Always lock off trigger switch when changing accessories.

Be sure to tighten chuck with two hands on both the rear sleeve and the forward sleeve for max-

imum tightness.

Chuck Removal (Fig. 7)

Always wear eye protection.

Turn the adjustment collar to the “drill” position. Tighten the chuck around the shorter end of a

hex key (not supplied) of 1/4” or greater size. Using a wooden mallet or similar object, strike the

longer end in the clockwise direction, as shown in FIG. 7. This will loosen the screw inside the

chuck.

Open chuck jaws fully, insert screwdriver (or Torx tool if required) into front of chuck between

jaws to engage screw head. Remove screw by turning clockwise (left-hand-thread). Place hex

key in chuck and tighten, as shown in FIG. 8. Using a wooden mallet or similar object, strike

key sharply in the counterclockwise direction. This will loosen the chuck so that it can be

unscrewed by hand.

Chuck Installation (Fig. 8)

Screw the chuck on by hand as far as it will go and insert screw (LH thread). Tighten screw

securely. Tighten the chuck around the shorter end of a 1/4” or larger hex key (not supplied)

strike the longer end in the clockwise direction with a wooden mallet, as shown in FIG. 7. Tighten

the screw once again by turning in a counterclockwise direction.

Operation as a Drill

Turn the collar to the drill bit symbol. Install and tighten the desired drill bit in the chuck. Follow

these instructions for best results when drilling:

DRILLING

1. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits, or

hole saws. For METAL, use high speed steel twist drill bits or hole saws.

2. Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material, use

a “back-up” block to prevent damage to the material.

3. Always apply pressure in a straight line with the bit. Use enough pressure to keep the drill bit

biting, but do not push hard enough to stall the motor or deflect the bit.

4. Hold tool firmly to control the twisting action of the drill.

5. IF DRILL STALLS, it is usually because it is being overloaded. RELEASE TRIGGER

IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK

TRIGGER OFF AND ON IN AN ATTEMPT TO START A STALLED DRILL – THIS CAN

DAMAGE THE DRILL.

6. To minimize stalling or breaking through the material, reduce pressure on drill and ease the

bit through the last fractional part of the hole.

7. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent

jamming.

8. With variable speed drills there is no need to center punch the point to be drilled. Use a slow

speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep

enough to drill without the bit skipping out. Operate at full on after starting the bit.

Drilling in Wood

Holes in wood can be made with the same twist drills used for metal. These bits may overheat

unless pulled out frequently to clear chips from the flutes. For larger holes, use low speed wood

bits. Work that is likely to splinter should be backed up with a block of wood.

Drilling in Metals

Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which

should be drilled dry. The cutting lubricants that work best are sulphurized cutting oil or lard oil;

bacon grease will also serve the purpose.

Operation as a Screwdriver

Insert the desired fastener accessory into the chuck as you would any drill bit. Make a few

practice runs in scrap or unseen areas to determine the proper position of the clutch collar.

Maintenance

CLEANING: With the motor running, blow dirt and dust out of all air vents with dry air at least

once a week. Wear safety glasses when performing this. Exterior plastic parts may be cleaned

with a damp cloth and mild detergent. Although these parts are highly solvent resistant,

NEVER use solvents.

POUR TOUT RENSEIGNEMENT SUPPLÉMENTAIRE SUR CET OUTIL OU TOUT AUTRE

OUTIL DEWALT, COMPOSER SANS FRAIS LE NUMÉRO :

1 800 4-D WALT (1 800 433-9258)E

Regles de sécurité générales pour tous les outils à

baterie

AVERTISSEMENT! Vous devez lire et comprendre toutes les instructions. Le non-

respect, même partiel, des instructions ci-après entraîne un risque de choc électrique, d’in-

cendie et/ou de blessures graves.

CONSERVEZ CES INSTRUCTIONS.

AIRE DE TRAVAIL

• Veillez à ce que l’aire de travail soit propre et bien éclairée. Le désordre et le manque de

lumière favorisent les accidents.

• N’utilisez pas d’outils électriques dans une atmosphère explosive, par exemple en

présence de liquides, de gaz ou de poussières inflammables. Les outils électriques créent

des étincelles qui pourraient enflammer les poussières ou les vapeurs.

• Tenez à distance les curieux, les enfants et les visiteurs pendant que vous travaillez avec

un outil électrique. Ils pourraient vous distraire et vous faire faire une fausse manoeuvre.

SÉCURITÉ ÉLECTRIQUE

• Ne maltraitez pas le cordon. Ne transportez pas l’outil par son cordon et ne débranchez pas la

fiche en tirant sur le cordon. N’exposez pas le cordon à la chaleur, à des huiles, à des arêtes vives

ou à des pièces en mouvement. Remplacez immédiatement un cordon endommagé. Un cordon

endommagé augmente le risque de choc électrique.

• Un outil à bloc-batterrie amovible ou à batterie intégrée ne doit être rechargé qu’avec le

chargeur prévu pour la batterie. Un chargeur qui convient à tel type de batterie peut présen-

teer un risque d’incendie avec tel autre type de batterie.

• N’utilisez un outil qu’avec un bloc-batterie conçu spécifiquement pour lui. L’emploi d’un

autre bloc-batterie peut créerr un risque d’incendie.

SÉCURITÉ DES PERSONNES

• Restez alerte, concentrez-vous sur votre travail et faites preuve de jugement. N’utilisez pas

un outil électrique si vous êtes fatigué ou sous l’influence de drogues, d’alcool ou de médica-

ments. Un instant d’inattention suffit pour entraîner des blessures graves.

• Habillez-vous convenablement. Ne portez ni vêtements flottants ni bijoux. Confinez les

cheveux longs. N’approchez jamais les cheveux, les vêtements ou les gants des pièces en mou-

vement. Des vêtements flottants, des bijoux ou des cheveux longs risquent d’être happés par des

pièces en mouvement.

• Méfiez-vous d’un démarrage accidental. Avant d’insérer un bloc-batterie, assurez-vous quee

l’interrupteur de l’outil est sur ARRÊT. Le fait de transporter un outil avec le doigt sur la détente

ou d’insérer un bloc-batterie alors que l’interrrupteur set en position MARCHE peut mener tout

droit à un accident.

• Enlevez les clés de réglage ou de serrage avant de démarrer l’outil. Une clé laissée dans un

pièce tournante de l’outil peut provoquer des blessures.

• Ne vous penchez pas trop en avant. Maintenez un bon appui et restez en équilibre en tout

temps. Un bonne stabilité vous permet de mieux réagir à une situation inattendue.

• Utilisez des accessoires de sécurité. Portez toujours des lunettes ou une visière. Selon les

conditions, portez aussi un masque antipoussière, des bottes de sécurité antidérapantes, un

casque protecteur et/ou un appareil antibruit.

UTILISATION ET ENTRETIEN DES OUTILS

• Immobilisez le matériau sur une surface stable au moyen de brides ou de toute autre

façon adéquate. Le fait de tenir la pièce avec la main ou contre votre corps offre un stabilité

insuffisante et peut amener un dérapage de l’outil.

• Ne forcez pas l’outil. Utilisez l’outil approprié à la tâche. L’outil correct fonctionne mieux et de

façon plus sécuritaire. Respectez aussi la vitesse de travail qui lui est propre.

• N’utilisez pas un outil si son interrupteur est bloqué. Un outil que vous ne pouvez pas com-

mander par son interrupteur est dangereux et droit être réparé.

• Retirez le bloc-batterie ou mettez l’interrupteur sur ARRÊT ou en position verrouillée

avant d’effectuer un réglage, de changer d’accessoire ou de ranger l’outil. De telled

mesures préventives réduisent le rrisque de démarrrage accidentel d l’outil.

• Rangez les outils hors de la portée des enfantes et d’autres personnes inexpérimentées.

Les outils sont dangereux dans les mains d’utilisateurs novices.

• Lorsque le bloc-batterie n’est pas en service, tenez-le à l’écart d’autres métalliques (trom-

bones, pièces de monnaie. clés, clous, vis, etc.) susceptibles d’établir un contact élec-

trique entre les deux bornes. La mise en court-circuit des bornes de la batterie peut produire

des éntincelles et constitue un risque de brûlures ou d’incendie.

• Prenez soin de bien entretenir les outils. Les outils de coupe doivent être toujours bien affûtés

et propres. Des outils bien entretenus, dont les arêtes sont bien tranchantes, sont moins sus-

ceptibles de coincer et plus faciles à diriger.

• Soyez attentif à tout désalignement ou coincement des pièces en mouvement, à tout bris

ou à toute autre condition préjudiciable au bon fonctionnement de l’outil. Si vous constatez

qu’un outil est endommagé, faites-le réparer avant de vous en servir. De nombreux accidents

sont causés par des outils en mauvais état.

• N’utilisez que des accessoires que le fabricant recommande pour votre modèle d’outil. Certains

accessoires peuvent convenir à un outil, mais être dangereux avec autre.

RÉPARATION

• La réparation des outils électriques doit être confiée à un réparateur qualifié. L’entretien ou

la réparation d’un outil électrique par un amateur peut avoir des conséquences graves.

• Pour la réparation d’un outil, n’employez que des pièces de rechange d’origine. Suivez les

directives données à la section «Réparation» de ce manuel. L’emploi de pièces non autorisées

ou le non-respect des instructions d’entretien peut créer un risque de choc électrique ou de

blessures.

Règles de sécurité additionnelles

• Tenir l’outil par les surfaces isolées prévues à cette fin lorsqu’il risque d’entrer en

contact avec des fils cachés ou son propre cordon, car de tels contacts peuvent mettre

les pièces métalliques de l’outil sous tension, engendrant des risques de choc électrique.

• Lorsqu’on est installé sur une échelle ou un échafaudage pour travailler, on doit

déposer l’outil sur le côté lorsqu’on ne s’en sert plus. Bien que certains outils munis

d’un gros bloc-piles puissent être placés à la verticale, dans cette position, ils peuvent facile-

ment être renversés.

•L’étiquette de l’outil peut comporter les symboles suivants.

V ..................volts A ..................ampères

Hz ................hertz W ..................watts

min................minutes ................courant alternatif

..............courant continu no..................sous vide

..................Construction de ..................borne de mise à la minute

....................classe II ../min ............tours à la minute

................symbole d´avertissement

CONSERVER CES MESURES

Importantes mesures de sécurité relatives au chargeur

• Le présent guide contient des conseils importants relatifs à la sécurité et à l’utilisation.

• Bien lire toutes les directives et tous les avertissements qui se trouvent sur (1) le chargeur, (2)

l’ensemble de piles et (3) l’outil avant d’utiliser le chargeur.

• DANGER : Les bornes du chargeur sont sous une tension de 120 volts. Ne pas les examin-

er avec un objet conducteur; cela présente des risques de secousses électriques.

•DANGER : Ne pas placer dans le chargeur un ensemble de piles craqué ou endommagé; cela

présente des risques de secousses électriques.

• Le chargeur et l’ensemble de piles ont été conçus pour fonctionner ensemble. NE JAMAIS ten-

ter de charger l’ensemble de piles à l’aide d’un chargeur autre que ceux décrits dans le présent

guide.

• Protéger le chargeur de la pluie ou de la neige.

• L’utilisation du chargeur pour tout ensemble de piles autre que les ensembles rechargeables

DEWALT comporte des risques d’incendie et de secousses électriques.

• Pour minimiser les risques de dommages au cordon et à sa fiche, débrancher l’appareil en tirant

sur la fiche plutôt que sur le cordon.

• Veiller à ce que le cordon soit rangé de sorte qu’on ne marche pas dessus, qu’il ne présente pas

de risques de blessures, et qu’il ne soit pas autrement sujet aux dommages et aux contraintes.

• Sauf nécessité absolue, ne jamais utiliser de cordon de rallonge. L’utilisation d’un cordon de ral-

longe non conforme présente des risques d’incendies et de secousses électriques.

• Les cordons de rallonge doivent être faits de conducteurs de calibre approprié (AWG ou jauge

américaine des fils) par mesure de sécurité. Le numéro de calibre du fil est inversement propor-

tionnel à la capacité du cordon. Ainsi, un cordon de calibre 16 a une capacité supérieure à celle

d’un cordon de calibre 18. Lorsqu’il est nècessaire d’utiliser plus d’un cordon de rallonge, veiller

à ce que chaque cordon ait au moins le calibre minimal.

CALIBRE MINIMAL RECOMMANDÉ (AWG)

POUR LES CORDONS DE RALLONGE

Longueur totale de cordon de rallonge (en mètres)

7,6 15 30 50

Calibre (AWG) du cordon

18 18 16 14

• La ventilation du chargeur se fait par les fentes sur le dessus et le dessous de l’appareil. Ne rien

déposer sur le chargeur et ne pas déposer ce dernier sur une surface qui pourrait en bloquer les

orifices car cela risque de provoquer la surchauffe de l’appareil. Éloigner le chargeur des sources

de chaleur.

• Ne jamais se servir du chargeur lorsque le cordon ou la fiche sont endommagés. Les remplacer

immédiatement.

• Ne jamais se servir d’un chargeur qui a encaissé un coup brusque, qui est tombé ou qui est

endommagé. Le faire vérifier à un centre de service autorisé.

• Ne jamais démonter le chargeur. N’en confier la réparation ou l’entretien qu’à un centre de ser-

vice autorisé. Le remontage non conforme du produit comporte des risques d’incendies ou de

secousses électriques.

• Pour minimiser les risques de secousses électriques, débrancher le chargeur de la prise de

courant avant de le nettoyer. Le risque n’est pas éliminé en enlevant l’ensemble de piles du

chargeur.

• NE JAMAIS raccorder deux chargeurs l’un à l’autre.

• NE PAS ranger le produit dans un endroit où la température peut atteindre ou dépasser 40 °C

(105 °F) (comme dans une remise métallique en été).

• Le chargeur est conçu pour fonctionner sur une alimentation domestique standard (120 volts).

Ne pas essayer de s’en servir sous toute autre tension.

Importantes mesures de sécurité relatives aux ensembles

de piles

L’ensemble de piles n’est pas complètement chargé à sa sortie de l’usine. Lire d’abord les instruc-

tions suivantes, puis se conformer aux directives relatives au chargement.

LIRE TOUTES LES DIRECTIVES.

• Ne pas incinérer l’ensemble de piles même s’il est très endommagé ou complètement usé. La

chaleur des flammes peut faire exploser les piles.

• Il peut se produire une légère fuite du liquide excitateur des piles dans des conditions d’utilisa-

CHARGER CLEANING INSTRUCTIONS:

WARNING: Disconnect the charger from the AC outlet before cleaning.

Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-

metallic brush. Do not use water or any cleaning solutions.

Accessories

Recommended accessories for use with your tool are available at extra cost from your local

service center.

CAUTION: The use of any non-recommended accessory may be hazardous.

If you need any assistance in locating any accessory, please contact D EWALT Industrial Tool

Co., 701 East Joppa Road, Baltimore, MD 21286 or call 1-800-4-D WALT. (1-800-433-9258)E

Maximum Recommended Capacity

BITS, METAL DRILLING 3/8"

WOOD, FLAT BORING 3/8”

Important

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (includ-

ing brush inspection and replacement) should be performed by certified service centers or

other qualified service organizations, always using identical replacement parts.

Full Warranty

DEWALT heavy duty industrial tools are warranted for one year from date of purchase. We will

repair, without charge, any defects due to faulty materials or workmanship. For warranty repair

information, call 1-800-4-DEWALT. This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by others. This warranty gives you spe-

cific legal rights and you may have other rights which vary in certain states or provinces.

In addition to the warranty, D EWALT tools are covered by our:

30 DAY NO RISK SATISFACTION GUARANTEE

If you are not completely satisfied with the performance of your D EWALT heavy duty industri-

al tool, simply return it to the participating seller within 30 days for a full refund. Please return

the complete unit, transportation prepaid. Proof of purchase may be required.

FIG. 1 FIG. 3

FIG. 2

FIG. 4

FIG. 5

FIG.8

FIG. 7

BBFIG. 6

Specyfikacje produktu

Marka:	DeWalt
Kategoria:	Wiertarka
Model:	DW925

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z DeWalt DW925, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Wiertarka DeWalt

DeWalt DWD450 Instrukcja

14 Października 2024

DeWalt DCH033 Instrukcja

9 Października 2024

DeWalt DWD216G Instrukcja

8 Października 2024

DeWalt DCD445 Instrukcja

8 Października 2024

DeWalt DW235G Instrukcja

8 Października 2024

DeWalt DC987-XE Instrukcja

7 Października 2024

DeWalt DW922K2 Instrukcja

7 Października 2024

DeWalt DCD932 Instrukcja

7 Października 2024

DeWalt D21717 Instrukcja

7 Października 2024

DeWalt DC930 Instrukcja

21 Września 2024

Instrukcje Wiertarka

Najnowsze instrukcje dla Wiertarka

Ozito BDP-500 Instrukcja

15 Października 2024

Einhell BM-G1100 E Instrukcja

14 Października 2024

Sun Joe 24V-DDK-LTX-PNK Instrukcja

14 Października 2024

Black & Decker GC1800 Instrukcja

13 Października 2024

Rupes BH 252R Instrukcja

13 Października 2024

Makita HP2070 Instrukcja

13 Października 2024

Makita DHR263ZJ Instrukcja

12 Października 2024

Black & Decker BDCDE120 Instrukcja

10 Października 2024

Gamma BH-1500W Instrukcja

9 Października 2024

Flex IW 1/2" 1500 18-EC Instrukcja

9 Października 2024