Instrukcja obsługi DeWalt DW160V
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DeWalt DW160V (7 stron) w kategorii Wiertarka. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/7

Defi nitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderate injury.
NOTICE: may Indicates a practice which, if not avoided, not related to personal injury
result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D WALT TOOL, CALL E
US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258).
WARNING: To reduce the risk of injury, read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a ground fault
circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
INSTRUCTION MANUAL
GUIDE D’UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y
PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
(APR13) Part No. N294579 DW160V Copyright © 2005, 2011, 2013 DEWALT
The following are trademarks for one or more D WALT power tools: the yellow and black color scheme, the “D” shaped E
air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on
the surface of the tool.
b) Protective Use personal protective equipment. Always wear eye protection.
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench
or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught
in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust collection can
reduce dust-related hazards.
4) POWER TOOL USE AND CARE
a) The Do not force the power tool. Use the correct power tool for your application.
correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool
that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Additional Specifi c Safety Rules for Right Angle Drills
• Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal
injury.
• Hold power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
• Use clamps or another practical way to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body leaves it unstable and may
lead to loss of control.
• Wear safety goggles or other eye protection. Drilling operations cause chips to fly. Flying
particles can cause permanent eye damage.
• Keep a firm grip on the tool at all times. Failure to do so will result in loss of control.
Breaking through or encountering hard materials such as re-bar may be hazardous as well.
• Accessories and tool may get hot during operation. Wear gloves when handling them
if performing heat producing applications such as drilling metals.
• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or
long hair can be caught in moving parts.
• An extension cord must have adequate wire size (AWG or American Wire Gauge)
for safety. The smaller the gauge number of the wire, the greater the capacity of the cable,
that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. When using more than one extension
to make up the total length, be sure each individual extension contains at least the minimum
wire size. The following table shows the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge
number, the heavier the cord.
Minimum Gauge for Cord Sets
Ampere Rating
Volts Total Length of Cord in Feet (meters)
120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
More
Than
Not More
Than AWG
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.
Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially designed to filter out microscopic
particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.
WARNING: Always wear proper personal hearing protection that conforms to ANSI
S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product
may contribute to hearing loss.
• The label on your tool may include the following symbols. The symbols and their definitions
are as follows:
V .....................volts A .........................amperes
Hz ...................hertz W ........................watts
min .................minutes or AC .............alternating current
or DC .....direct current or AC/DC......alternating or direct current
...................Class I Construction no .......................no load speed
....
....
....
........
....
....
........
....
....
.......
...
...
.......
....
....
.......
...
...
....
.
.
.(grounded) n .........................rated speed
................... Class II Construction .......................earthing terminal
(double insulated) ........................safety alert symbol
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-800-4-D WALT • www.dewalt.comE
DW160V
3/8" (10mm) VSR Right Angle Drill
Perceuse à angle droit VSR 10 mm (3/8 po)
Taladro de ángulo recto de 3/8" (10 mm) VSR

…/min ............per minute BPM ...................beats per minute
IPM .................impacts per minute RPM ...................revolutions per minute
SPM ...............strokes per minute sfpm ...................surface feet per minute
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Motor
Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than
10% will cause loss of power and overheating. DEWALT tools are factory tested; if this tool does
not operate, check power supply.
COMPONENTS (Fig. 1)
WARNING: Never modify the power tool or any part of it. Damage or personal injury could
result.
A. Paddle C. Chuck guard
B. Forward/reverse switch D. Chuck
Variable Speed Switch (Fig. 1)
To turn the tool on, squeeze the paddle (A) that runs the length of the tool, as shown in
Figure1. To turn the tool off, release the paddle.
A variable speed paddle switch permits speed control—the farther the switch is depressed, the
higher the speed of the drill.
NOTE: Continuous use in variable speed range is not recommended. It may damage the switch
and should be avoided.
Forward/Reverse Switch (Fig. 1, 2)
Release paddle (A) and allow the tool to come to a complete stop. Slide the forward/reverse
switch (B) to the opposite position.
NOTE: Do not reverse direction of tool while the motor is running.
ADJUSTMENTS
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power
source before installing and removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury.
Chuck (Fig. 3, 4)
Open chuck jaws by aligning hole (E) in chuck (D) with an opening (F) in the chuck guard (C).
Insert the chuck key (G) through the opening and into the chuck. Insert shank of bit about 3/4"
(19mm) into chuck. It’s important to tighten chuck with all three holes (E). To release bit, turn
chuck key (G) counterclockwise in just one of the holes.
Chuck Key Holder (Fig. 4)
1. Push double-hole end of chuck key holder (H) through slot in other end of holder.
2. Slip loop over electric plug and draw loop tight around cord.
3. Push ends of chuck key handle through two holes in end of holder.
OPERATION
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power
source before installing and removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury.
Drilling (Fig. 5, 6, 7)
1. Use sharp drill bits only.
• For WOOD, use twist drill bits, spade bits, power auger bits, or hole saws.
• For METAL, use high speed steel twist drill bits or hole saws.
• For MASONRY, such as brick, cement, cinder block, etc., use carbide-tipped bits.
2. Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material, use a
“back-up” block to prevent damage to the material.
3. Always apply pressure in a straight line with the bit. Use enough pressure to keep the drill
bit biting, but do not push hard enough to stall the motor or deflect the bit.
4. Hold tool firmly to control the twisting action of the drill.
5. IF DRILL STALLS, it is usually because it is being overloaded. RELEASE TRIGGER
IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK
TRIGGER OFF AND ON IN AN ATTEMPT TO START A STALLED DRILL – THIS CAN
DAMAGE THE DRILL.
6. To minimize stalling on breaking through the material, reduce pressure on drill and ease the
bit through the last fractional part of the hole.
7. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent
jamming.
8. For optimum control and comfort, the drill may be grasped in one of the following illustrated
manners: Around the neck of the drill using one or two fingers to operate the paddle switch
as in Figure5, in an inverted position with the heel of the hand pushing on the head of the
drill and one or two fingers on the paddle switch as in Figure 6, or holding the head of the
drill with one hand and operating the paddle switch with the other hand, holding the back
end of the drill as in Figure 7.
Drilling in Wood
Holes in wood can be made with the same twist drills used for metal. These bits may overheat
unless pulled out frequently to clear chips from the flutes. For larger holes, use spade bits, power
auger bits, or hole saws. Work that is likely to splinter should be backed up with a block of wood.
Drilling in Metal
Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which
should be drilled dry. The cutting lubricants that work best are sulphurized cutting oil or lard oil;
bacon grease will also serve the purpose.
Drilling in Masonry
Use carbide tipped masonry bits at low speeds. Keep even force on the drill but not so much
that you crack the brittle materials. A smooth, even flow of dust indicates the proper drilling
rate.
MAINTENANCE
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power
source before installing and removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing this.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered by D WALT, have not been tested E
with this product, use of such accessories with this tool could be hazardous. To reduce the risk
of injury, only DEWALT recommended accessories should be used with this product.
Recommended accessories for use with your tool are available at extra cost from your local dealer
or authorized service center. If you need assistance in locating any accessory, please contact
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-DEWALT
(1-800-433-9258) or visit our website: www.dewalt.com.
For safety in use, the following accessories should be used only in sizes up to the maximums
shown in the table below.
SPECIFICATIONS
Chuck Size 3/8" (9.5 mm)
Drill Speed (RPM) 1200
D
C
A
B
B
FIG. 1
FIG. 7
FIG. 3
F
E
C
FIG. 4
H
FIG. 6FIG. 5
A
FIG. 2
MAXIMUM RECOMMENDED CAPACITIES
Twist bits in metal 3/8" (9.5 mm)
Flat boring bits in wood 1-1/4" (31.7 mm)
Carbide tipped bits in masonry 9/16" (14.2 mm)
Hole saws in wood or metal 1-1/4" (31.7 mm)
CAUTION: Accessories must be rated for at least the speed recom mended on the
tool warning label. Wheels and other accessories running over rated speed can fly apart
and cause injury. Accessory ratings must always be above tool speed as shown on tool
nameplate.
Wire wheel brushes 4" ( diameter maximum101.6 mm)
Wire cup brushes 3" ( diameter maximum76.2 mm)
Buffing wheels 3" (76.2 mm) diameter maximum
Rubber backing pads 4-5/8" diameter maximum(117.4 mm)
ROUND-SHANK MASONRY BITS
These bits are carbide-tipped for top performance and extra long life in most masonry drilling
applications.
BIT USABLE SHANK
DIAMETER DRILLING DEPTH DIAMETER
3/16" (3.8 mm) 38.1 mm) 3.8 mm)1-1/2" ( 3/16" (
1/4" (6.3 mm) 50.8 mm) 6.3 mm)2" ( 1/4" (
5/16" (3.1 mm) 57.1 mm) 6.3 mm) 2-1/4" ( 1/4" (
3/8" (9.5 mm) 63.5 mm) 6.3 mm) 2-1/2" ( 1/4" (
1/2" (12.7 mm) 63.5 mm) 6.3 mm) 2-1/2" ( 1/4" (
9/16" (14.2 mm) 107.9 mm) 6.3 mm) 4-1/4" ( 1/4" (
HIGH-SPEED HOLE SAWS (use with mandrels)
SAW OUTSIDE FOR CONDUIT FOR PIPE TAP
DIAMETERS SIZES SIZES
5/8" (15.8 mm) Built in mandrel no separate mandrel
3/4" (19 mm) 9.5 mm)3/8" (
7/8" (22.2 mm) 12.7 mm)1/2" (
1-5/16" (33.3 mm) 19 mm)3/4" (
1" (25.4 mm)
1-1/16" (26.9 mm)
1-1/8" (28.5 mm) 19 mm)3/4" (
1-3/16" (30.1 mm) 25.4 mm)1" (
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including
brush inspection and replacement) should be performed by a DEWALT factory service center,
a D WALT authorized service center or other qualified service personnel. Always use identical E
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRANTY SERVICE: Registering your product will help you obtain more efficient
warranty service in case there is a problem with your product.
• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or
theft, your registration of ownership will serve as your proof of purchase.
• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely
event a safety notification is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials or workmanship for
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to
accessories or damage caused where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have other rights which vary in certain
states or provinces.
G
D

Défi nitions: lignes directrices en
matière de sécurité
Les définitions ci-dessous décrivent le niveau de danger pour chaque
mot-indicateur employé. Lire le mode d’emploi et porter une attention particulière
à ces symboles.
DANGER : indique une situation dangereuse imminente qui, si elle n’est pas
évitée, entraînera la mort ou des blessures graves.
AVERTISSEMENT: indique une situation potentiellement dangereuse qui,
si elle n’est pas évitée, entraîner lapourrait mort ou des blessures graves.
ATTENTION: indique une situation potentiellement dangereuse qui, si elle
n’est pas évitée, entraîner des pourrait blessures légères ou modérées.
AVIS : indique une pratique ne posant aucun risque de dommages corporels
mais qui par contre, si rien n’est fait pour l’éviter, pourrait poser des risques de
dommages matériels.
POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL OU DE TOUT AUTRE
OUTIL DEWALT, COMPOSEZ LE NUMÉRO SANS FRAIS : 1-800-4-DEWALT (1-800-433-
9258).
AVERTISSEMENT : afin de réduire le risque de blessures, lire le mode d’emploi de l’outil.
Avertissements de sécurité généraux pour les outils
électriques
AVERTISSEMENT ! Lire tous les avertissements de sécurité et toutes les
directives. Le non-respect des avertissements et des directives pourrait se solder par
un choc électrique, un incendie et/ou une blessure grave.
CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES
LES DIRECTIVES POUR UN USAGE ULTÉRIEUR
Le terme « outil électrique » cité dans les avertissements se rapporte à votre outil électrique à
alimentation sur secteur (avec fil) ou par piles (sans fil).
1) SÉCURITÉ DU LIEU DE TRAVAIL
a) Tenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont
propices aux accidents.
b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, tel qu’en
présence de liquides, de gaz ou de poussières inflammables. Les outils électriques
produisent des étincelles qui pourraient enflammer la poussière ou les vapeurs.
c) Éloigner les enfants et les personnes à proximité pendant l’utilisation d’un outil
électrique. Une distraction pourrait en faire perdre la maîtrise à l’utilisateur.
2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ
a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais
modifier la fiche d’aucune façon. Ne jamais utiliser de fiche d’adaptation avec un
outil électrique mis à la terre. Le risque de choc électrique sera réduit par l’utilisation
de fiches non modifiées correspondant à la prise.
b) Éviter tout contact physique avec des surfaces mises à la terre comme des
tuyaux, des radiateurs, des cuisinières et des réfrigérateurs. Le risque de choc
électrique est plus élevé si votre corps est mis à la terre.
c) Ne pas exposer les outils électriques à la pluie ou à l’humidité. La pénétration de
l’eau dans un outil électrique augmente le risque de choc électrique.
d) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour
transporter, tirer ou débrancher un outil électrique. Tenir le cordon éloigné de
la chaleur, de l’huile, des bords tranchants et des pièces mobiles. Les cordons
endommagés ou enchevêtrés augmentent les risques de choc électrique.
e) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge
convenant à cette application. L’utilisation d’une rallonge conçue pour l’extérieur
réduira les risques de choc électrique.
f) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit
humide, brancher l’outil dans une prise ou sur un circuit d’alimentation dotés
d’un disjoncteur de fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur réduit
les risques de choc électrique.
3) SÉCURITÉ PERSONNELLE
a) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un
outil électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue
ou sous l’influence de drogues, d’alcool ou de médicaments. Un simple moment
d’inattention en utilisant un outil électrique peut entraîner des blessures corporelles
graves.
b) Utiliser des équipements de protection individuelle. Toujours porter une
protection oculaire. L’utilisation d’équipements de protection comme un masque
antipoussière, des chaussures antidérapantes, un casque de sécurité ou des protecteurs
auditifs lorsque la situation le requiert réduira les risques de blessures corporelles.
c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve
à la position d’arrêt avant de relier l’outil à une source d’alimentation et/ou
d’insérer un bloc-piles, de ramasser ou de transporter l’outil. Transporter un outil
électrique alors que le doigt repose sur l’interrupteur ou brancher un outil électrique dont
l’interrupteur est à la position de marche risque de provoquer un accident.
d) Retirer toute clé de réglage ou clé avant de démarrer l’outil. Une clé ou une clé de
réglage attachée à une partie pivotante de l’outil électrique peut provoquer des blessures
corporelles.
e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela permet
de mieux maîtriser l’outil électrique dans les situations imprévues.
f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de
bijoux. Garder les cheveux, les vêtements et les gants à l’écart des pièces
mobiles. Les vêtements amples, les bijoux ou les cheveux longs risquent de rester
coincés dans les pièces mobiles.
g) Si des composants sont fournis pour le raccordement de dispositifs de
dépoussiérage et de ramassage, s’assurer que ceux-ci sont bien raccordés et
utilisés. L’utilisation d’un dispositif de dépoussiérage peut réduire les dangers engendrés
par les poussières.
4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE
a) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à l’application.
L’outil électrique approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse
pour laquelle il a été conçu.
b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout outil
électrique dont l’interrupteur est défectueux est dangereux et doit être réparé.
c) Débrancher la fiche de la source d’alimentation et/ou du bloc-piles de l’outil
électrique avant de faire tout réglage ou changement d’accessoire ou avant de
ranger l’outil. Ces mesures préventives réduisent les risques de démarrage accidentel
de l’outil électrique.
d) Ranger les outils électriques hors de la portée des enfants et ne permettre à
aucune personne n’étant pas familière avec un outil électrique ou son mode
d’emploi d’utiliser cet outil. Les outils électriques deviennent dangereux entre les
mains d’utilisateurs inexpérimentés.
e) Entretien des outils électriques. Vérifier si les pièces mobiles sont mal alignées
ou coincées, si des pièces sont brisées ou présentent toute autre condition
susceptible de nuire au bon fonctionnement de l’outil électrique. En cas de
dommage, faire réparer l’outil électrique avant toute nouvelle utilisation.
Beaucoup d’accidents sont causés par des outils électriques mal entretenus.
f) S’assurer que les outils de coupe sont aiguisés et propres. Les outils de coupe bien
entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles à maîtriser.
g) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux
présentes directives en tenant compte des conditions de travail et du travail
à effectuer. L’utilisation d’un outil électrique pour toute opération autre que celle pour
laquelle il a été conçu est dangereuse.
5) RÉPARATION
a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant
que des pièces de rechange identiques. Cela permettra de maintenir une utilisation
sécuritaire de l’outil électrique.
Règles de sécurité spécifi ques supplémentaires pour les
perceuses à angle droit
• Utiliser la/les poignée(s) auxiliaire(s) si fournie(s) avec l’outil. Une perte de contrôle de
l’outil pourrait occasionner des dommages corporels.
• Tenir l’outil par les surfaces isolées prévues à cet effet pendant toute utilisation où
l’organe de coupe pourrait entrer en contact avec des fils électriques cachés ou
son propre cordon. Tout contact de l’organe de coupe avec un fil sous tension mettra les
parties métalliques exposées de l’outil sous tension et électrocutera l’utilisateur.
• Utiliser des brides de fixation ou tout autre dispositif de fixation permettant de
soutenir et de retenir la pièce sur une plate-forme stable. Tenir la pièce avec la main
ou contre son corps est instable et risque de provoquer une perte de maîtrise de l’outil.
• Porter des lunettes de protection ou toute autre protection oculaire. Le perçage
pourrait faire voltiger des éclats. Des particules volantes pourraient occasionner des
dommages oculaires permanents.
• Maintenir systématiquement l’outil fermement. Le non-respect de cette directive
pourrait entrainer la perte de contrôle de l’outil. Traverser ou rencontrer des matériaux durs,
comme les armatures, peut aussi s’avérer dangereux.
• Les accessoires et l’outil peuvent devenir brûlants au toucher pendant l’utilisation.
Porter des gants pendant leur utilisation pour effectuer des travaux produisant beaucoup de
chaleur comme le perçage des métaux.
• Prendre des précautions à proximité des évents, car ils cachent des pièces mobiles.
Vêtements amples, bijoux ou cheveux longs risquent de rester coincés dans ces pièces
mobiles.
• Pour la sécurité de l’utilisateur, utiliser une rallonge de calibre adéquat (AWG,
American Wire Gauge [calibrage américain normalisé des fils électriques]). Plus le
calibre est petit, et plus sa capacité est grande. Un calibre16, par exemple, a une capacité
supérieure à un calibre18. L’usage d’une rallonge de calibre insuffisant causera une chute
de tension qui entraînera perte de puissance et surchauffe. Si plus d’une rallonge est utilisée
pour obtenir une certaine longueur, s’assurer que chaque rallonge présente au moins le
calibre de fil minimum. Le tableau ci-dessous illustre les calibres à utiliser selon la longueur
de rallonge et l’intensité nominale indiquée sur la plaque signalétique. En cas de doute, utiliser
le calibre suivant. Plus le calibre est petit, plus la rallonge peut supporter de courant.
Calibres minimaux des rallonges
Intensité (en ampères) volts Longueur totale de cordon en mètres (pieds)
120 V 7,6 (25) 15,2 (50) 30,5 (100) 45,7 (150)
240 V 15,2 (50) 30,5 (100) 61,0 (200) 91,4 (300)
Supérieur à Inférieur à AWG
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Non recommandé
AVERTISSEMENT: porter SYSTEMATIQUEMENT des lunettes de protection. Les lunettes
courantes NE sont PAS des lunettes de protection. Utiliser aussi un masque antipoussières si
la découpe doit en produire beaucoup. PORTER SYSTÉMATIQUEMENT UN ÉQUIPEMENT DE
SÉCURITÉ HOMOLOGUÉ:
• Protection oculaire ANSI Z87.1 (CAN/CSA Z94.3);
• Protection auditive ANSI S12.6 (S3.19);
• Protection des voies respiratoires NIOSH/OSHA/MSHA.
AVERTISSEMENT : les scies, meules, ponceuses, perceuses ou autres outils de
construction peuvent produire des poussières contenant des produits chimiques reconnus par
l’État californien pour causer cancers, malformations congénitales ou être nocifs au système
reproducteur. Parmi ces produits chimiques, on retrouve:
• Le plomb dans les peintures à base de plomb;
• La silice cristallisée dans les briques et le ciment, ou autres produits de maçonnerie; et
• L’arsenic et le chrome dans le bois ayant subi un traitement chimique.
Le risque associé à de telles expositions varie selon la fréquence à laquelle on effectue ces
travaux. Pour réduire toute exposition à ces produits: travailler dans un endroit bien aéré, en
utilisant du matériel de sécurité homologué, tel un masque antipoussières spécialement conçu
pour filtrer les particules microscopiques.
• Limiter toute exposition prolongée avec les poussières provenant du ponçage,
sciage, meulage, perçage ou toute autre activité de construction. Porter des
vêtements de protection et nettoyer à l’eau savonneuse les parties du corps
exposées. Le fait de laisser la poussière pénétrer dans la bouche, les yeux ou la peau peut
favoriser l’absorption de produits chimiques dangereux.
AVERTISSEMENT: cet outil peut produire et/ou répandre de la poussière susceptible de
causer des dommages sérieux et permanents au système respiratoire. Utiliser systématiquement
un appareil de protection des voies respiratoires homologué par le NIOSH ou l’OSHA. Diriger les
particules dans le sens opposé au visage et au corps.
AVERTISSEMENT: pendant l’utilisation, porter systématiquement une protection
auditive individuelle adéquate homologuée ANSI S12.6 (S3.19). Sous certaines conditions
et suivant la durée d’utilisation, le bruit émanant de ce produit pourrait contribuer à une perte
de l’acuité auditive.
• L’étiquette apposée sur votre outil peut inclure les symboles suivants. Les symboles et leur
définition sont indiqués ci-après:
V .................... volts A .......................ampères
Hz .................. hertz W ...................... watts
min ................minutes ou AC .......... courant alternatif
ou DC ....courant continu ou AC/DC ... courant alternatif ou
..................classe I fabrication continu
(mis à la terre) no ..................... vitesse à vide
..................fabrication classe II n ....................... vitesse nominale
(double isolation) ..................... borne de terre
…/min ...........par minute ...................... symbole d’avertissement
In addition to the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time
during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt
for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country specific warranty information contained in the packaging, call
the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-DEWALT (1-800-433-9258) for a free replacement.
TO REDUCE THE RISK OF INJURY, USER
MUST READ INSTRUCTION MANUAL.
ALWAYS USE PROPER EYE AND RESPIRATORY PROTECTION.
SER.
DEWALT INDUSTRIAL TOOL CO., BALTIMORE, MD 21286 USA
FOR SERVICE INFORMATION, CALL 1-800-4-
D
E EWALT www.D WALT.com
WARNING
ADVERTENCIA/AVERTISSEMENT
PARA EL MANEJO SEGURO LEA EL MANUAL DE INSTRUCCIONES.
SIEMPRE SE DEBERÁ LLEVAR LA PROTECCIÓN APROPIADA PARA LA
VISTA Y PARA LAS VÍAS RESPIRATORIAS.
À TITRE PRÉVENTIF, LIRE LE GUIDE. IL FAUT TOUJOURS PORTER DE
L’ÉQUIPEMENT DE PROTECTION OCULAIRE ET RESPIRATOIRE APPROPRIÉ.
DW160V
3/8" (10mm) VSR RIGHT ANGLE DRILL
Specyfikacje produktu
Marka: | DeWalt |
Kategoria: | Wiertarka |
Model: | DW160V |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z DeWalt DW160V, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Wiertarka DeWalt

15 Stycznia 2025

5 Stycznia 2025

3 Stycznia 2025

30 Grudnia 2025

23 Grudnia 2024

14 Października 2024

9 Października 2024

8 Października 2024

8 Października 2024

8 Października 2024
Instrukcje Wiertarka
- Wiertarka Ikea
- Wiertarka AEG
- Wiertarka Worx
- Wiertarka Kawasaki
- Wiertarka Milwaukee
- Wiertarka Stihl
- Wiertarka Bosch
- Wiertarka Yato
- Wiertarka Parkside
- Wiertarka Global
- Wiertarka Toolcraft
- Wiertarka Festool
- Wiertarka Panasonic
- Wiertarka Bavaria By Einhell
- Wiertarka Stanley
- Wiertarka Black & Decker
- Wiertarka Scheppach
- Wiertarka Proxxon
- Wiertarka Ribimex
- Wiertarka Hazet
- Wiertarka RIKON
- Wiertarka Einhell
- Wiertarka Genesis
- Wiertarka Hyundai
- Wiertarka Silverline
- Wiertarka Makita
- Wiertarka Ozito
- Wiertarka RYOBI
- Wiertarka Flex
- Wiertarka GO/ON
- Wiertarka DEDRA
- Wiertarka Baumr-AG
- Wiertarka Biltema
- Wiertarka Hilti
- Wiertarka BaseTech
- Wiertarka Max Bahr
- Wiertarka Trotec
- Wiertarka Dremel
- Wiertarka Handwerk
- Wiertarka Velleman
- Wiertarka Meec Tools
- Wiertarka Güde
- Wiertarka Bavaria
- Wiertarka Cecotec
- Wiertarka Zipper
- Wiertarka Mafell
- Wiertarka Delta
- Wiertarka Ferrex
- Wiertarka DURO PRO
- Wiertarka McKenzie
- Wiertarka Westfalia
- Wiertarka Ergotools Pattfield
- Wiertarka Fein
- Wiertarka Ferm
- Wiertarka Hitachi
- Wiertarka Herkules
- Wiertarka Craftsman
- Wiertarka Fieldmann
- Wiertarka Ridgid
- Wiertarka PowerPlus
- Wiertarka Alpha Tools
- Wiertarka Vonroc
- Wiertarka Powerfix
- Wiertarka HiKOKI
- Wiertarka Workzone
- Wiertarka Porter-Cable
- Wiertarka Metabo
- Wiertarka Cotech
- Wiertarka Skil
- Wiertarka Toolland
- Wiertarka Kinzo
- Wiertarka Tryton
- Wiertarka Sun Joe
- Wiertarka Tacklife
- Wiertarka Luxor
- Wiertarka Maktec
- Wiertarka Steren
- Wiertarka Bort
- Wiertarka Tanaka
- Wiertarka Malmbergs
- Wiertarka Power Craft
- Wiertarka Eibenstock
- Wiertarka Topcraft
- Wiertarka Festo
- Wiertarka Sparky
- Wiertarka Gamma
- Wiertarka Carat
- Wiertarka Kress
- Wiertarka Duro
- Wiertarka Berner
- Wiertarka Varo
- Wiertarka Defort
- Wiertarka Max
- Wiertarka Truper
- Wiertarka Bruder Mannesmann
- Wiertarka Powerblade
- Wiertarka Meister Craft
- Wiertarka Rupes
- Wiertarka Batavia
- Wiertarka Protool
- Wiertarka Economy
- Wiertarka Holzmann
- Wiertarka Graphite
- Wiertarka Huvema
- Wiertarka Black Decker
- Wiertarka Stomer
- Wiertarka Elu
- Wiertarka Fe Powertools
- Wiertarka Blucave
- Wiertarka Ecomac
- Wiertarka Lux Tools
- Wiertarka Kreg
- Wiertarka Sthor
- Wiertarka Verto
- Wiertarka Wurth
- Wiertarka Spit
- Wiertarka King Craft
- Wiertarka Rok
- Wiertarka Profitech
- Wiertarka Narex
- Wiertarka Baier
- Wiertarka RUKO
- Wiertarka Toolson
- Wiertarka Felisatti
- Wiertarka MSW
- Wiertarka Robust
- Wiertarka Einhell Bavaria
- Wiertarka MyTool
- Wiertarka G-Technology
- Wiertarka Stalco
- Wiertarka Total
- Wiertarka Netter Vibration
Najnowsze instrukcje dla Wiertarka

14 Stycznia 2025

12 Stycznia 2025

11 Stycznia 2025

11 Stycznia 2025

11 Stycznia 2025

11 Stycznia 2025

10 Stycznia 2025

10 Stycznia 2025

10 Stycznia 2025

10 Stycznia 2025