Instrukcja obsługi DeWalt DC901

DeWalt Wiertarka DC901

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DeWalt DC901 (7 stron) w kategorii Wiertarka. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/7

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

DEWALT Industrial Tool Co., 701 Joppa Road, Towson, MD 21286

The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme;

the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the

array of lozenge-shaped humps on the surface of the tool.

DC901

Heavy-Duty 36V 1/2" (13 mm) Cordless Hammerdrill / Marteau perforateur

industriel de 1/2 po (13 mm ) sans fil de 36 volts / Taladro percutor inalámbrico de

36 V para de 13 mm (1/2") trabajo pesado

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-D WALT • www.dewalt.comE

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the

manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury.

NOTICE: may Indicates a practice not related to personal injury which, if not avoided,

result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D WALT TOOL, CALL E

US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault

circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric

shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while operating power tools may

result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energizing power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or

a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) The Do not force the power tool. Use the correct power tool for your application.

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits, etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed. Use of the power tool for operations different from those intended could result

in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the manufacturer. A charger that is

suitable for one type of battery pack may create a risk of fire when used with another battery

pack.

b) Use power tools only with specifically designated battery packs. Use of any other

battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects, like paper

clips, coins, keys, nails, screws, or other small metal objects, that can make a

connection from one terminal to another. Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the battery may cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Speciﬁ c Safety Rules for Hammerdrills

• Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.

• Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

• Hold power tool by insulated gripping surfaces, when performing an operation where

the cutting accessory may contact hidden wiring. Cutting accessory contacting a "live"

wire may make exposed metal parts of the power tool "live" and could give the operator an

electric shock.

• Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

• Wear ear protectors when hammering for extended periods of time. Prolonged exposure

to high intensity noise can cause hearing loss. Temporary hearing loss or serious ear drum

damage may result from high sound levels generated by hammerdrilling.

• Wear safety goggles or other eye protection. Hammering and drilling operations cause

chips to fly. Flying particles can cause permanent eye damage.

• Always use the side handle supplied with the tool. Keep a firm grip on the tool at all times.

Do not attempt to operate this tool without holding it with both hands.

• Hammer bits and tools get hot during operation. Wear gloves when touching them.

• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long

hair can be caught in moving parts.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use

face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the State of California to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

WARNING: Always wear proper personal hearing protection that conforms to ANSI

S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product

may contribute to hearing loss.

CAUTION: When not in use, place tool on its side on a stable surface where it will not

cause a tripping or falling hazard. Some tools with large battery packs will stand upright on the

battery pack but may be easily knocked over.

• The label on your tool may include the following symbols. The symbols and their definitions are

as follows:

V .....................volts A .........................amperes

Hz ...................hertz W ........................watts

min .................minutes or AC .............alternating current

or DC .....direct current or AC/DC......alternating or direct current

...................Class I Construction no .......................no load speed

...

......

...

......

...

......

...

......

...

......

...

.....

...

...(grounded) n .........................rated speed

...................Class II Construction .......................earthing terminal

(double insulated) ........................safety alert symbol

…/min ............per minute BPM ...................beats per minute

IPM .................impacts per minute RPM ...................revolutions per minute

SPM ...............strokes per minute sfpm ...................surface feet per minute

Important Safety Instructions for All Battery Packs

When ordering replacement battery packs, be sure to include catalog number and voltage. Consult

the chart at the end of this manual for compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using the battery pack and charger,

read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Inserting or removing the battery from the charger may

ignite the dust or fumes.

• NEVER force battery pack into charger. DO NOT modify battery pack in any way to fit

into a non-compatible charger as battery pack may rupture causing serious personal

injury. Consult the chart at the end of this manual for compatibility of batteries and chargers.

• Charge the battery packs only in DEWALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations where the temperature may

reach or exceed 105 °F (40 °C) (such as outside sheds or metal buildings in summer).

WARNING: Never attempt to open the battery pack for any reason. If battery pack case is

cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do

not use a battery pack or charger that has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Damaged battery

packs should be returned to service center for recycling.

WARNING: Fire hazard. Do not store or carry battery so that metal objects can

contact exposed battery terminals. For example, do not place battery in aprons, pockets, tool

boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc. without battery cap.

Transporting batteries can possibly cause fires if the battery terminals inadvertently

come in contact with conductive materials such as keys, coins, hand tools and the like.

The U.S. Department of Transportation Hazardous Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes (i.e., packed in suitcases and carry-on luggage)

UNLESS they are properly protected from short circuits. So when transporting individual batteries,

make sure that the battery terminals are protected and well insulated from materials that could

contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely damaged or is completely

worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin, immediately wash area with mild

soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes

or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a

mixture of liquid organic carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If

symptoms persist, seek medical attention.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

The RBRCTM Seal

The RBRC™ (Rechargeable Battery Recycling Corp oration) Seal on the nickel

cadmium, nickel metal hydride or lithiumion batteries (or battery packs) indicate that

the costs to recycle these batteries (or battery packs) at the end of their useful life

have already been paid by DEWALT. In some areas, it is illegal to place spent nickel

cadmium, nickel metal hydride or lithium ion batteries in the trash or municipal solid

waste stream and the RBRC program provides an environmentally conscious

alternative.

RBRC™ in cooperation with DEWALT and other battery users, has established programs in the

United States and Canada to facilitate the collection of spent nickel cadmium, nickel metal hydride

or lithium ion batteries. Help protect our environment and conserve natural resources by returning

the spent nickel cadmium, nickel metal hydride or lithium ion batteries to an authorized DEWALT

service center or to your local retailer for recycling. You may also contact your local recycling center

for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.

Important Safety Instructions for All Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions

for battery chargers.

• Before using charger, read all instructions and cautionary markings on charger, battery pack,

and product using battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside the charger. Electric shock may

result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only D WALT rechargeable battery E

packs. Other types of batteries may overheat and burst resulting in personal injury and property

damage.

NOTICE: Under certain conditions, with the charger plugged in to the power supply, the exposed

charging contacts inside the charger can be shorted by foreign material. Foreign materials of a

conductive nature such as, but not limited to, grinding dust, metal chips, steel wool, aluminum foil,

or any buildup of metallic particles should be kept away from charger cavities. Always unplug the

charger from the power supply when there is no battery pack in the cavity. Unplug charger before

attempting to clean.

• DO NOT attempt to charge the battery pack with any chargers other than the ones in

this manual. The charger and battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than charging DEWALT

rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger. This will reduce risk of damage

to electric plug and cord.

• Make sure that cord is located so that it will not be stepped on, tripped over, or

otherwise subjected to damage or stress.

• Do not use an extension cord unless it is absolutely necessary. Use of improper extension

cord could result in risk of fire, electric shock, or electrocution.

• When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for

safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is

16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using more than one extension to make up

the total length, be sure each individual extension contains at least the minimum wire size. The

following table shows the correct size to use depending on cord length and nameplate ampere

rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the

cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not More

Than AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of charger or place the charger on a soft surface that

might block the ventilation slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated through slots in the top and

the bottom of the housing.

• Do not mount charger on wall or permanently affix charger to any surface. The charger

is intended to use on a flat, stable surface (i.e., table top, bench top).

• Do not operate charger with damaged cord or plug.

• Do not operate charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way. Take it to an authorized service center.

• Do not disassemble charger; take it to an authorized service center when service or

repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting any cleaning. This will

reduce the risk of electric shock. Removing the battery pack will not reduce this risk.

• NEVER attempt to connect two chargers together.

• The charger is designed to operate on standard 120 volt household electrical power.

Do not attempt to use it on any other voltage. This does not apply to the vehicular charger.

Chargers

Your tool uses a D WALT charger. Be sure to read all safety instructions before using your charger. E

Consult the chart at the end of this manual for compatibility of chargers and battery packs.

Charging Procedure (Fig. 9)

1. Plug the charger into an appropriate outlet before inserting battery pack.

2. Insert the battery pack (H) into the charger, as shown in Figure 9, making sure the pack is fully

seated in charger. The charger is equipped with a three-light fuel gauge that will blink according

to the state of charge of the battery pack.

3. The completion of charge is indicated by the three red lights remaining ON continuously. The

pack is fully charged and may be used at this time or left on the charger.

0% - 33% 1st light blinks

33% - 66% 1st light on, 2nd light blinks

66% - 99% 1st, 2nd lights on, 3rd light blinks

100% 1st, 2nd, 3rd lights on

Charger Diagnostics

This charger is designed to detect certain problems that can arise with the battery packs or the

charger. Problems are indicated by the three red lights flashing together in different patterns.

PROBLEM POWERLINE

When the charger is used with some portable power sources such as generators or sources that

convert DC to AC, the charger may temporarily suspend operation. The three red lights will flash

together with . This indicates that the power souce is out two fast blinks followed by a pause

of limits.

BAD BATTERY

The charger can detect a weak or damaged battery. The three red lights will flash together with

rapid blinking. The battery will no longer charge and should be returned to a service center or a

collection site for recycling.

BAD CHARGER

The charger will detect if it is not functioning properly. The three red lights will flash together with

one fast blink followed by a long blink. The charger will no longer work and should be returned

to an authorized service center or replaced.

LEAVING THE BATTERY IN THE CHARGER

The charger and battery pack can be left connected with the red lights glowing indefinitely. The

charger will keep the battery pack fresh and fully charged. This charger features an automatic tune-

up mode which equals or balances the individual cells in the battery pack to allow it to function

at peak capacity. Battery packs should be tuned up weekly or whenever the battery no longer

delivers the same amount of work. To use the automatic tune-up mode, place the battery pack in

the charger and leave it for at least 8 hours.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery pack is charged when the air

temperature is between 65 °F and 75 °F (18 °–24 °C). DO NOT charge the battery pack in an

air temperature below +40 °F (+4.5 °C), or above +105 °F (+40.5°C). This is important and will

prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a normal

condition, and does not indicate a problem. To facilitate the cooling of the battery pack after

use, avoid placing the charger or battery pack in a warm environment such as in a metal shed,

or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other appliance;

b. Check to see if receptacle is connected to a light switch which turns power off when you turn

out the lights;

c. Move charger and battery pack to a location where the surrounding air temperature is

approximately 65 °F–75 °F (18°– 24 °C);

d. If charging problems persist, take the tool, battery pack and charger to your local service

center.

4. The battery pack should be recharged when it fails to produce sufficient power on jobs which

were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack whenever you desire with no

adverse affect on the battery pack.

5. Under certain conditions, with the charger plugged into the power supply, the exposed

charging contacts inside the charger can be shorted by foreign material. Foreign materials of a

conductive nature such as, but not limited to, steel wool, aluminum grinding dust, metal chips,

foil, or any buildup of metallic particles should be kept away from charger cavities. Always

unplug the charger from the power supply when there is no battery pack in the cavity. Unplug

charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside charger. Electric shock may result.

WARNING: Burn hazard. Never attempt to open the battery pack for any reason. If the plastic

housing of the battery pack breaks or cracks, return to a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct sunlight and excess heat

or cold.

2. For long storage, it is recommended to store a fully charged battery pack in a cool dry place

out of the charger for optimal results.

NOTE: Battery packs should not be stored completely depleted of charge. The battery pack will

need to be recharged before use.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

COMPONENTS (Fig. 1)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.

A. Trigger switch E. Gear shifter

B. Forward/reverse control (lock-off) button F. Chuck sleeve

C. Mode control collar G. Battery release button

D. Torque adjustment collar H. Battery pack

KEY FEATURES AND FUNCTIONS

Variable Speed Switch (Fig. 1)

To turn the tool on, squeeze the trigger switch (A). To turn the tool off, release the trigger switch.

Your tool is equipped with a brake. The chuck will stop as soon as the trigger switch is fully released.

NOTE: Continuous use in variable speed range is not recommended. It may damage the switch

and should be avoided.

Forward/Reverse Control Button (Fig. 1)

A forward/reverse control button (B) determines the direction the tool will spin and also serves as

a lock-off button.

To select forward rotation, release the trigger switch and depress the for ward/re verse control button

on the right side of the tool.

To select reverse, depress the forward/reverse control button on the left side of the tool.

The center position of the control button locks the tool in the OFF position. When changing the

position of the control button, be sure the trigger is released.

NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click on

start up. This is normal and does not indicate a problem.

Mode Control Collar

Your drill is equipped with a separate mode control collar (Fig. 1, C) to switch between drilling,

screwdriving and hammerdrilling mode.

SCREWDRIVING (FIG. 2)

1. Select the desired speed/torque range using the three-speed gear shifter (E) on the top of tool

to match the speed and torque to the planned application. To set the torque level to the proper

setting on the clutch collar, initially set the clutch collar at a lower setting to ensure the fastener

to be set to your specification.

NOTE: Use the lowest torque setting required to seat the fastener at the desired depth. The

lower the number, the lower the torque output.

2. Rotate the mode control collar (C) so the screw symbol is aligned with the arrow.

3. Set the torque adjustment collar (D) to the appropriate number setting for the torque desired.

NOTE: The torque adjustment collar may be set on any number and change between

screwdriving and drilling modes using the mode control collar.

DRILLING (FIG. 3)

CAUTION: When the mode collar is in the drill/hammerdrill mode, the drill will not clutch out

regardless of the position of the torque adjustment collar (D).

Rotate the mode control collar (C) so the drill symbol is aligned with the arrow.

NOTE: The torque adjustment collar (D) may be set on any number.

HAMMERDRILLING (FIG. 4)

Rotate the mode control collar (C) so the hammer symbol is aligned with the arrow.

Torque Adjustment Collar (Fig. 2)

Your tool has an adjustable torque screwdriver mechanism for driving and removing a wide array of

fastener shapes and sizes and a hammer mechanism for drilling into masonry. Circling the torque

adjustment collar (D) are numbers. These numbers are used to set the clutch to deliver a torque

range. The higher the number on the collar, the higher the torque and the larger the fastener which

can be driven. To select any of the numbers, rotate until the desired number aligns with the arrow.

Three-Speed Gearing (Fig. 2)

The three-speed feature of your tool allows you to shift gears for greater versatility. To select speed

1 (highest torque setting), turn the tool off and permit it to stop. Slide the gear shifter (E) all the way

to the left. Speed 2 (middle torque and speed setting) is in the middle position. Speed 3 (highest

speed setting) is to the right.

NOTE: Do not change gears when the tool is running. Always allow the drill to come to a complete

stop before changing gears. If you have trouble changing gears, make sure that the gear shifter is

engaged in one of the three speed settings.

Keyless Single Sleeve Chuck (Fig. 5–7)

WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part

of the chuck and turning the tool on. Damage to the chuck and personal injury may result. Always

lock off trigger switch and disconnect tool from power source when changing acces sories.

WARNING: Always ensure the bit is secure before starting the tool. A loose bit may eject from

tool causing possible personal injury.

TO INSERT A DRILL BIT OR OTHER ACCESSORY

Your tool features a keyless chuck with one rotating sleeve for one-handed operation of the chuck.

To insert a drill bit or other accessory, follow these steps.

1. Turn tool off and disconnect tool from power source.

2. Grasp the black sleeve of the chuck (F) with one hand and use the other hand to secure the tool

as shown in Figure 5. Rotate the sleeve counterclockwise (as viewed from the front) far enough

to accept the desired accessory.

3. Insert the accessory about 3/4" (19 mm) into the chuck and tighten securely by rotating the

chuck sleeve clockwise with one hand while holding the tool with the other hand. Continue to

rotate the chuck sleeve until several ratchet clicks are heard to ensure full gripping power.

Be sure to tighten chuck with one hand on the chuck sleeve and one hand holding the tool for

maximum tightness.

To release the accessory, repeat Steps 1 and 2 above.

OPERATION

WARNING: To reduce the risk of serious personal injury, turn tool off and remove the

battery pack before making any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Installing and Removing the Battery Pack (Fig. 8)

NOTE: For best results, make sure your battery pack is fully charged.

CAUTION: Make certain the forward/reverse (lock-off) button (B), as shown in Figure 1, is

engaged to prevent switch actuation before removing or installing battery.

To install the battery pack into the tool handle, align the battery pack with the rails inside the tool’s

handle and slide it into the handle until the battery pack is firmly seated in the tool and ensure that

it does not disengage.

To remove the battery pack from the tool, press the release button (G) and firmly pull the battery

pack out of the tool handle. Insert it into the charger as described in the charger section of this

manual.

Side Handle

WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side handle

properly installed. Failure to do so may result in the side handle slipping during tool operation and

subsequent loss of control. Hold tool with both hands to maximize control.

Side handle clamps to the front of the gear case as shown and may be rotated to

permit right- or left-hand use. Side handle must be tightened sufficiently to

resist the twisting action of the tool if the accessory binds or stalls. Be sure

to grip the side handle at the far end to control the tool during a stall.

If model is not equipped with side handle, grip drill with one hand on the

handle and one hand on the battery pack.

Screwdriver Operation (Fig. 2)

Select the desired speed/torque range using the three-speed gear shifter (E) on the top of tool

to match the speed and torque to the planned operation. Insert the desired fastener accessory

into the chuck as you would any drill bit. Set the torque adjustment collar (D) to the desired

setting. Make a few practice runs in scrap or unseen areas to determine the proper position of the

clutch collar.

Drill Operation (Fig. 3)

1. Select the desired speed/torque range using the gear shifter (E) to match the speed and torque

to the planned operation.

2. For WOOD, use twist bits, spade bits, power auger bits or hole saws. For METAL, use high-

speed steel twist drill bits or hole saws. Use a cutting lubricant when drilling metals. The

exceptions are cast iron and brass which should be drilled dry.

3. Always apply pressure in a straight line with the bit. Use enough pressure to keep the drill bit

biting, but do not push hard enough to stall the motor or deflect the bit.

4. Hold tool firmly with both hands to control the twisting action of the drill.

5. IF DRILL STALLS, RELEASE TRIGGER it is usually because it is being overloaded.

IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK

TRIGGER OFF AND ON IN AN ATTEMPT TO START A STALLED DRILL – THIS CAN

DAMAGE THE DRILL.

6. Keep the motor running when pulling the bit back out of a drilled hole. This will help prevent

jamming.

Hammerdrill Operation (Fig. 4)

1. When drilling, use just enough force on the hammer to keep it from bouncing excessively or

“rising” off the bit. Too much force will cause slower drilling speeds, overheating, and a lower

drilling rate.

2. Drill straight, keeping the bit at a right angle to the work. Do not exert side pressure on the bit

when drilling as this will cause clogging of the bit flutes and a slower drilling speed.

3. When drilling deep holes, if the hammer speed starts to drop off, pull the bit partially out of the

hole with the tool still running to help clear debris from the hole.

4. For MASONRY, use carbide-tipped bits or masonry bits. A smooth, even flow of dust indicates

the proper drilling rate.

MAINTENANCE

WARNING: To reduce the risk of serious personal injury, turn tool off and remove the

battery pack before making any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week. To

minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when performing

this.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts

of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse

any part of the tool into a liquid.

FIG. 8

FIG. 9

FIG. 5 FIG. 6 FIG. 7

FIG. 2

SCREWDRIVING

VISSAGE

DESTORNILLADOR

FIG. 4

HAMMERDRILLING

MARTEAU PERFORATEUR

TALADRO PERCUTOR

FIG. 3

DRILLING

PERÇAGE

TALADRO

FIG. 1

g) Si des composants sont fournis pour le raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux-ci sont bien raccordés et utilisés. L’utilisation

d’un dispositif de dépoussiérage peut réduire les dangers engendrés par les poussières.

4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE

a) Ne pas forcer un outil électrique. Utiliser l’outil électrique approprié à l’application.

L’outil électrique approprié effectuera un meilleur travail, de façon plus sûre et à la vitesse

pour laquelle il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur est défectueux. Tout outil

électrique dont l’interrupteur est défectueux est dangereux et doit être réparé.

c) Débrancher la fiche de la source d’alimentation et/ou du bloc-piles de l’outil

électrique avant de faire tout réglage ou changement d’accessoire ou avant de

ranger l’outil. Ces mesures préventives réduisent les risques de démarrage accidentel de

l’outil électrique.

d) Ranger les outils électriques hors de la portée des enfants et ne permettre à

aucune personne n’étant pas familière avec un outil électrique ou son mode

d’emploi d’utiliser cet outil. Les outils électriques deviennent dangereux entre les mains

d’utilisateurs inexpérimentés.

e) Entretien des outils électriques. Vérifier si les pièces mobiles sont mal alignées ou

coincées, si des pièces sont brisées ou présentent toute autre condition susceptible

de nuire au bon fonctionnement de l’outil électrique. En cas de dommage, faire

réparer l’outil électrique avant toute nouvelle utilisation. Beaucoup d’accidents sont

causés par des outils électriques mal entretenus.

f) S’assurer que les outils de coupe sont aiguisés et propres. Les outils de coupe bien

entretenus et affûtés sont moins susceptibles de se coincer et sont plus faciles à maîtriser.

g) Utiliser l’outil électrique, les accessoires, les forets, etc. conformément aux

présentes directives en tenant compte des conditions de travail et du travail à

effectuer. L’utilisation d’un outil électrique pour toute opération autre que celle pour laquelle

il a été conçu est dangereuse.

5) UTILISATION ET ENTRETIEN DU BLOC-PILES

a) L’utilisation Ne recharger l’outil qu’au moyen du chargeur précisé par le fabricant.

d’un chargeur qui convient à un type de bloc-piles risque de provoquer un incendie s’il est

utilisé avec un autre type de b loc-piles.

b) Utiliser les outils électriques uniquement avec les blocs-piles conçus à cet effet.

L’utilisation de tout autre bloc-piles risque de causer des blessures ou un incendie.

c) Lorsque le bloc-piles n’est pas utilisé, le tenir éloigné des objets métalliques,

notamment des trombones, de la monnaie, des clés, des clous, des vis ou autres

petits objets métalliques qui peuvent établir une connexion entre les deux bornes.

Le court-circuit des bornes du bloc-piles risque de provoquer des brûlures ou un incendie.

d) En cas d’utilisation abusive, le liquide peut gicler hors du bloc-piles; éviter tout

contact avec ce liquide. Si un contact accidentel se produit, laver à grande eau. Si

le liquide entre en contact avec les yeux, obtenir également des soins médicaux. Le

liquide qui gicle hors du bloc-piles peut provoquer des irritations ou des brûlures.

6) RÉPARATION

a) Faire réparer l’outil électrique par un réparateur professionnel en n’utilisant que

des pièces de rechange identiques. Cela permettra de maintenir une utilisation sécuritaire

de l’outil électrique.

Règles de sécurité spéciﬁ ques pour les marteaux

perforateurs

• Porter des protecteurs auditifs si une perceuse à percussion est utilisée. Une exposition

au bruit peut entraîner une perte auditive.

• Utiliser la/les poignée(s) auxiliaire(s) si fournie(s) avec l’outil. Une perte de contrôle de

l’outil pourrait occasionner des dommages corporels.

• Tenir l’outil par les surfaces isolées prévues à cet effet pendant toute utilisation où

l’organe de coupe pourrait entrer en contact avec des fils électriques cachés. Tout

contact de l’organe de coupe avec un fil sous tension mettra les parties métalliques exposées

de l’outil sous tension et électrocutera l’utilisateur.

• Utiliser des brides de fixation ou tout autre dispositif de fixation permettant de

soutenir et de retenir la pièce sur une plate-forme stable. Tenir la pièce avec la main ou

contre son corps est instable et risque de provoquer une perte de maîtrise de l’outil.

• Porter des protecteurs auditifs lors de martelage sur des périodes prolongées. Une

exposition prolongée à un bruit d’intensité élevé peut provoquer une perte auditive. Les niveaux

sonores élevés produits par le marteau perforateur pourraient provoquer une perte auditive

temporaire ou endommager gravement les tympans.

• Porter des lunettes de sécurité ou une autre protection oculaire. Le martelage et la

perforation peuvent projeter des fragments. Les particules projetées peuvent endommager les

yeux irréversiblement.

• Toujours utiliser la poignée latérale fournie avec l’outil. Tenir fermement l’outil en tout

temps. Ne pas utiliser l’outil sans le tenir des deux mains.

• Les mèches à maçonnerie et les outils deviennent chauds en cours de fonctionnement.

Pour les toucher, porter des gants.

• Prendre des précautions à proximité des évents, car ils cachent des pièces mobiles.

Vêtements amples, bijoux ou cheveux longs risquent de rester coincés dans ces pièces mobiles.

AVERTISSEMENT: porter SYSTEMATIQUEMENT des lunettes de protection. Les lunettes

courantes NE sont PAS des lunettes de protection. Utiliser aussi un masque antipoussières si

la découpe doit en produire beaucoup. PORTER SYSTÉMATIQUEMENT UN ÉQUIPEMENT DE

SÉCURITÉ HOMOLOGUÉ:

• Protection oculaire ANSI Z87.1 (CAN/CSA Z94.3);

• Protection auditive ANSI S12.6 (S3.19);

• Protection des voies respiratoires NIOSH/OSHA/MSHA.

AVERTISSEMENT: les scies, meules, ponceuses, perceuses ou autres outils de construction

peuvent produire des poussières contenant des produits chimiques reconnus par l’État californien

pour causer cancers, malformations congénitales ou être nocifs au système reproducteur. Parmi

ces produits chimiques, on retrouve:

• Le plomb dans les peintures à base de plomb;

• La silice cristallisée dans les briques et le ciment, ou autres produits de maçonnerie; et

• L’arsenic et le chrome dans le bois ayant subi un traitement chimique.

Le risque associé à de telles expositions varie selon la fréquence à laquelle on effectue ces travaux.

Pour réduire toute exposition à ces produits: travailler dans un endroit bien aéré, en utilisant du

matériel de sécurité homologué, tel un masque antipoussières spécialement conçu pour filtrer les

particules microscopiques.

• Limiter toute exposition prolongée avec les poussières provenant du ponçage, sciage,

meulage, perçage ou toute autre activité de construction. Porter des vêtements de

protection et nettoyer à l’eau savonneuse les parties du corps exposées. Le fait de

laisser la poussière pénétrer dans la bouche, les yeux ou la peau peut favoriser l’absorption de

produits chimiques dangereux.

AVERTISSEMENT : cet outil peut produire et/ou répandre de la poussière susceptible de

causer des dommages sérieux et permanents au système respiratoire. Utiliser systématiquement

un appareil de protection des voies respiratoires homologué par le NIOSH ou l’OSHA. Diriger les

particules dans le sens opposé au visage et au corps.

AVERTISSEMENT : pendant l’utilisation, porter systématiquement une protection

auditive individuelle adéquate homologuée ANSI S12.6 (S3.19). Sous certaines conditions

et suivant la durée d’utilisation, le bruit émanant de ce produit pourrait contribuer à une perte de

l’acuité auditive.

ATTENTION: après utilisation, ranger l’outil sur son côté, sur une surface stable, là où

il ne pourra ni faire trébucher ni faire chuter quelqu’un. Certains outils équipés d’un large

bloc-piles peuvent tenir à la verticale sur celui-ci, mais manquent alors de stabilité.

• L’étiquette apposée sur votre outil peut inclure les symboles suivants. Les symboles et leur

définition sont indiqués ci-après:

V ....................volts A ....................... ampères

Hz ..................hertz W ...................... watts

min ................minutes ou AC .......... courant alternatif

ou DC ....courant continu ou AC/DC ... courant alternatif ou

..................classe I fabrication continu

(mis à la terre) no ..................... vitesse à vide

..................fabrication classe II n ....................... vitesse nominale

(double isolation) ..................... borne de terre

…/min ...........par minute ...................... symbole d’avertissement

IPM ................impacts par minute BPM .................battements par minute

sfpm ..............pieds linéaires par minute (plpm) r/min ................. tours par minute

SPM (FPM) ....fréquence par minute

Consignes de sécurité importantes propres à tous les

blocs-piles

Pour commander un bloc-piles de rechange, s’assurer d’inclure son numéro de catalogue et

sa tension. Consulter le tableau figurant à la fin du présent mode d’emploi pour connaître la

compatibilité des chargeurs et des blocs-piles.

Le bloc-piles n’est pas totalement chargé d’usine. Avant d’utiliser le bloc-piles et le chargeur, lire les

consignes de sécurité ci-dessous. Puis suivre la procédure de charge indiquée.

LIRE TOUTES LES CONSIGNES

• Ne pas recharger ou utiliser un bloc-piles en milieu déflagrant, en présence, par

exemple, de poussières, gaz ou liquides inflammables. Le fait d’insérer ou retirer un bloc-

piles de son chargeur pourrait causer l’inflammation de poussières ou d’émanations.

• NE JAMAIS forcer l’insertion d’un bloc-piles dans un chargeur. NE modifier un bloc-

piles d’AUCUNE façon pour le faire rentrer dans un chargeur incompatible, car il

pourrait se briser et causer des dommages corporels graves. Consulter le tableau en

dernière page de ce manuel pour connaître les compatibilités entre chargeurs et blocs-piles.

• Recharger les blocs-piles exclusivement dans des chargeurs DEWALT.

• NE PAS éclabousser le bloc-piles ou l’immerger dans l’eau ou dans tout autre liquide.

• Ne pas entreposer ou utiliser l’appareil et le bloc-piles en présence de températures

ambiantes pouvant excéder 40°C (105°F) (comme dans des hangars ou des bâtiments

métalliques l’été).

AVERTISSEMENT : ne jamais ouvrir le bloc-piles pour quelque raison que ce soit. Si le boîtier

du bloc-piles est fissuré ou endommagé, ne pas l’insérer dans un chargeur. Ne pas broyer,

échapper ou endommager le bloc-piles. Ne pas utiliser un bloc-piles ou un chargeur qui a reçu

un choc violent, qui est tombé, écrasé ou qui a été endommagé de quelque manière que ce

soit (p. ex. percé par un clou, frappé d’un coup de marteau, marché dessus). Les blocs-piles

endommagés doivent être envoyés au centre de réparation pour être recyclés.

AVERTISSEMENT : risque d’incendie. Ne pas ranger ni ne transporter les piles de

manière à ce que des objets métalliques puissent entrer en contact avec les bornes

exposées des piles. On ne doit pas mettre, par exemple, le bloc-piles sans capuchon dans un

tablier, une poche, une boîte à outils, une boîte de nécessaire de produit, un tiroir, etc. avec des

clous, des vis, des clés, etc. Le transport des piles peut causer un incendie si les bornes des

piles entrent en contact involontairement avec des matières conductrices comme des

clés, de la monnaie, des outils manuels et d’autres éléments semblables. La Hazardous

Material Regulations (réglementation sur les produits dangereux) du département américain des

transports interdit en fait le transport des blocs-piles pour le commerce et dans les avions (c.-à-d.

dans des valises et les bagages à main) À MOINS qu’ils ne soient bien protégés contre les

courts-circuits. Pour le transport de piles individuelles, on doit donc s’assurer que les bornes sont

protégées et bien isolées contre toute matière pouvant entrer en contact avec elles et provoquer

un court-circuit.

DIRECTIVES DE SÉCURITÉ SPÉCIFIQUES POUR LES PILES AU LITHIUM-ION (Li-Ion)

• Ne pas incinérer le bloc-piles même s’il est sévèrement endommagé ou complètement

usagé, car il pourrait exploser et causer un incendie. Pendant l’incinération des blocs-piles au

lithium-ion, des vapeurs et matières toxiques sont dégagées.

• En cas de contact du liquide de la pile avec la peau, rincer immédiatement au savon

doux et à l’eau. En cas de contact oculaire, rincer l’œil ouvert à l’eau claire une quinzaine de

minutes ou jusqu’à ce que l’irritation cesse. Si des soins médicaux s’avéraient nécessaires,

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and

grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush.

Do not use water or any cleaning solutions.

Repairs

The charger and battery pack are not serviceable.

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush

inspection and replacement) should be performed by a DEWALT factory service center, a DEWALT

authorized service center or other qualified service personnel. Always use identical replacement

parts.

Accessories

WARNING: Since accessories, other than those offered by D WALT, have not been tested with E

this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury,

only DEWALT recommended accessories should be used with this product.

Recommended accessories for use with your tool are available at extra cost from your local dealer or

authorized service center. If you need assistance in locating any accessory, please contact DEWALT

Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286, call 1-800-4-DEWALT (1-800-433-

9258) or visit our website: www.dewalt.com.

MAXIMUM RECOMMENDED CAPACITIES

Speed 1 Speed 2 Speed 3

BITS, METALDRILLING 1/2" (12,7 mm) 1/4" (6.4 mm) 1/4" (6.4 mm)

WOOD, FLATBORING 1-1/2" (38.1 mm) 5/8" (15.9 mm) 5/8" (15.9 mm)

BITS, MASONRYDRILLING – 1/4" (6.4 mm) 1/4" (6.4 mm)

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty

service in case there is a problem with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft,

your registration of ownership will serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event

a safety notification is required under the Federal Consumer Safety Act.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three

years from the date of purchase. This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.

com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to accessories or

damage caused where repairs have been made or attempted by others. This warranty gives you

specific legal rights and you may have other rights which vary in certain states or provinces.

In addition to the warranty, DEWALT tools are covered by our:

1 YEAR FREE SERVICE

DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time

during the first year after purchase.

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9280, DC9360, DC9180,

DCB120, DCB127, DCB201, DCB203 and DCB361

3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DCB200, DCB204, DCB205

DEWALT BATTERY PACKS

Product warranty voided if the battery pack is tampered with in any way. DEWALT is not responsible

for any injury caused by tampering and may prosecute warranty fraud to the fullest extent permitted

by law.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer

for any reason, you can return it within 90 days from the date of purchase with a receipt for a full

refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products

sold in Latin America, see country specific warranty information contained in the packaging, call the

local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing,

call 1-800-4-DEWALT (1-800-433-9258) for a free replacement.

Déﬁ nitions: lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de danger pour chaque

mot-indicateur employé. Lire le mode d’emploi et porter une attention particulière

à ces symboles.

DANGER: indique une situation dangereuse imminente qui, si elle n’est pas

évitée, entraînera la mort ou des blessures graves.

AVERTISSEMENT: indique une situation potentiellement dangereuse qui,

si elle n’est pas évitée, entraîner lapourrait mort ou des blessures graves.

ATTENTION: indique une situation potentiellement dangereuse qui, si elle

n’est pas évitée, entraîner des pourrait blessures légères ou modérées.

AVIS : indique une pratique ne posant aucun risque de dommages corporels

mais qui par contre, si rien n’est fait pour l’éviter, poser despourrait risques de

dommages matériels.

POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL OU DE TOUT AUTRE

OUTIL DEWALT, COMPOSEZ LE NUMÉRO SANS FRAIS : 1-800-4-DEWALT (1-800-433-9258).

AVERTISSEMENT : afin de réduire le risque de blessures, lire le mode d’emploi de l’outil.

Avertissements de sécurité généraux pour les outils

électriques

AVERTISSEMENT! lire tous les avertissements de sécurité et toutes les directives.

Le non-respect des avertissements et des directives pourrait se solder par un choc

électrique, un incendie et/ou une blessure grave.

CONSERVER TOUS LES AVERTISSEMENTS ET TOUTES LES

DIRECTIVES POUR UN USAGE ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se rapporte à votre outil électrique à

alimentation sur secteur (avec fil) ou par piles (sans fil).

1) SÉCURITÉ DU LIEU DE TRAVAIL

a) Tenir l’aire de travail propre et bien éclairée. Les lieux encombrés ou sombres sont

propices aux accidents.

b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, tel qu’en

présence de liquides, de gaz ou de poussières inflammables. Les outils électriques

produisent des étincelles qui pourraient enflammer la poussière ou les vapeurs.

c) Éloigner les enfants et les personnes à proximité pendant l’utilisation d’un outil

électrique. Une distraction pourrait en faire perdre la maîtrise à l’utilisateur.

2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ

a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais modifier

la fiche d’aucune façon. Ne jamais utiliser de fiche d’adaptation avec un outil

électrique mis à la terre. Le risque de choc électrique sera réduit par l’utilisation de fiches

non modifiées correspondant à la prise.

b) Éviter tout contact physique avec des surfaces mises à la terre comme des tuyaux,

des radiateurs, des cuisinières et des réfrigérateurs. Le risque de choc électrique est

plus élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à l’humidité. La pénétration de l’eau

dans un outil électrique augmente le risque de choc électrique.

d) Ne pas utiliser le cordon de façon abusive. Ne jamais utiliser le cordon pour

transporter, tirer ou débrancher un outil électrique. Tenir le cordon éloigné de

la chaleur, de l’huile, des bords tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se servir d’une rallonge

convenant à cette application. L’utilisation d’une rallonge conçue pour l’extérieur réduira

les risques de choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil électrique dans un endroit

humide, brancher l’outil dans une prise ou sur un circuit d’alimentation dotés d’un

disjoncteur de fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur réduit les

risques de choc électrique.

3) SÉCURITÉ PERSONNELLE

a) Être vigilant, surveiller le travail effectué et faire preuve de jugement lorsqu’un outil

électrique est utilisé. Ne pas utiliser d’outil électrique en cas de fatigue ou sous

l’influence de drogues, d’alcool ou de médicaments. Un simple moment d’inattention

en utilisant un outil électrique peut entraîner des blessures corporelles graves.

b) Utiliser des équipements de protection individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection comme un masque antipoussière, des

chaussures antidérapantes, un casque de sécurité ou des protecteurs auditifs lorsque la

situation le requiert réduira les risques de blessures corporelles.

c) Empêcher les démarrages intempestifs. S’assurer que l’interrupteur se trouve à la

position d’arrêt avant de relier l’outil à une source d’alimentation et/ou d’insérer un

bloc-piles, de ramasser ou de transporter l’outil. Transporter un outil électrique alors

que le doigt repose sur l’interrupteur ou brancher un outil électrique dont l’interrupteur est à

la position de marche risque de provoquer un accident.

d) Retirer toute clé de réglage ou clé avant de démarrer l’outil. Une clé ou une clé de

réglage attachée à une partie pivotante de l’outil électrique peut provoquer des blessures

corporelles.

e) Ne pas trop tendre les bras. Conserver son équilibre en tout temps. Cela permet de

mieux maîtriser l’outil électrique dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de vêtements amples ni de bijoux.

Garder les cheveux, les vêtements et les gants à l’écart des pièces mobiles. Les

vêtements amples, les bijoux ou les cheveux longs risquent de rester coincés dans les pièces

mobiles.

Specyfikacje produktu

Marka:	DeWalt
Kategoria:	Wiertarka
Model:	DC901

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z DeWalt DC901, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Wiertarka DeWalt

DeWalt DWD450 Instrukcja

14 Października 2024

DeWalt DCH033 Instrukcja

9 Października 2024

DeWalt DWD216G Instrukcja

8 Października 2024

DeWalt DCD445 Instrukcja

8 Października 2024

DeWalt DW235G Instrukcja

8 Października 2024

DeWalt DC987-XE Instrukcja

7 Października 2024

DeWalt DW922K2 Instrukcja

7 Października 2024

DeWalt DCD932 Instrukcja

7 Października 2024

DeWalt D21717 Instrukcja

7 Października 2024

DeWalt DC930 Instrukcja

21 Września 2024

Instrukcje Wiertarka

Najnowsze instrukcje dla Wiertarka

Ozito BDP-500 Instrukcja

15 Października 2024

Einhell BM-G1100 E Instrukcja

14 Października 2024

Sun Joe 24V-DDK-LTX-PNK Instrukcja

14 Października 2024

Black & Decker GC1800 Instrukcja

13 Października 2024

Rupes BH 252R Instrukcja

13 Października 2024

Makita HP2070 Instrukcja

13 Października 2024

Makita DHR263ZJ Instrukcja

12 Października 2024

Black & Decker BDCDE120 Instrukcja

10 Października 2024

Gamma BH-1500W Instrukcja

9 Października 2024

Flex IW 1/2" 1500 18-EC Instrukcja

9 Października 2024