Instrukcja obsługi Dell Dimension 4400

Dell Niesklasyfikowane Dimension 4400

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dell Dimension 4400 (59 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/59

Dell™Dimension™4400

Technical Overview

Controls and Lights

Solving Problems

System Codes and Messages

Technical Specifications

System Setup Program

Adding Parts

Documentation

Hints, Notices, and Cautions

Abbreviations and Acronyms

For a complete list of abbreviations and acronyms, see the Tell Me How help file.

Information in this document is subject to change without notice.

©2002DellComputerCorporation.Allrightsreserved.

Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and Dimension are trademarks of Dell Computer Corporation; Intel and Pentium are registered trademarks of Intel Corporation;

Microsoft and Windows are registered trademarks of Microsoft Corporation; Adobe is a trademark of Adobe Systems Incorporated.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation

disclaims any proprietary interest in trademarks and trade names other than its own.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision

Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited

viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

May 2002 Rev. A04

HINT: A HINT indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Back to Contents Page

System Codes and Messages

Dell™Dimension™4400

Diagnostic Codes

POST Beep Codes

System Messages

Diagnostic Codes

Your computer is equipped with four diagnostic lights, which are labeled "A," "B," "C," and "D" on the back of the computer. Each of the four lights can be

yellow, green, or off as shown in the following table. When the computer is turned on or restarted and it is functioning normally, the lights flash during POST.

After the computer starts, the lights remain green to signify normal computer operation.

If a malfunction is detected and the computer fails to start, the lights display a code that identifies the problem. Write down the diagnostic code displayed and

look it up in the following table.



Diagnostic Code

Definition

Corrective Action



Power up default.

Make sure that the computer is connected to a known working electrical outlet, and then check

whether the front-panel power light on the power button is on or off. If the power light is off, check

the power supply. If the problem persists, see "Contacting Dell" in the Owner's Manual for instructions

on obtaining technical assistance.

See "Safety Instructions," and then remove all cards.Ifthecomputerstilldoesnotstart,see

"Contacting Dell" in the Owner's Manual for instructions on obtaining technical assistance.



System board is receiving

power, but the BIOS is not

executing.

Set the configuration jumper to Maintenance mode, and restart the computer. Exit and save changes

in the system setup program. Turn off the computer and reset the configuration jumper to Normal

mode, and then restart the computer.

See "Safety Instructions," and then remove all cards and restart the computer to determine if a

resource conflict exists. If conflict exists, see "Resolving Software and Hardware Incompatibilities." If

the problem persists, see "Contacting Dell" in the Owner's Manual for instructions on obtaining

technical assistance.



Recovery mode from BIOS

failure.

Set the configuration jumper to Maintenance mode and restart the computer. Exit and save changes in

the system setup program. Turn off the computer and reset the configuration jumper to Normal mode,

and then restart the computer.

See "Safety Instructions," and then remove all cards and restart the computer to determine if a

resourceconflictexists.Ifconflictexists,see"Resolving Software and Hardware Incompatibilities." If

the problem persists, see "Contacting Dell" in the Owner's Manual for instructions on obtaining

technical assistance.



Microprocessor has failed a

BIOS test.

If the problem persists, see "Contacting Dell" in the Owner's Manual for instructions on obtaining

technical assistance.



Memory failed to be sized or

enabled.

Reseat the memory modules.Iftheproblempersists,see"ContactingDell"intheOwner's Manual for

instructions on obtaining technical assistance.



PCI bus failure has occurred.

See "Safety Instructions," and then remove all cards and restart the computer to determine if a

resource conflict exists. If conflict exists, see "Resolving Software and Hardware Incompatibilities." If

the problem still persists, see "Contacting Dell" in the Owner's Manual for instructions on obtaining

technical assistance.



Video controller failed to

initialize or respond.

If the computer has a video card, reseat the video card. If the problem persists or the computer has

integrated video, see "Contacting Dell" in the Owner's Manual for instructions on obtaining technical

assistance.



IDE bus failure has occurred.

Reseat the drive cables. If the problem persists, see "Contacting Dell" in the Owner's Manual for

instructions on obtaining technical assistance.



USB port or a device

connected to it has failed

initialization.

Disconnect the device from the USB connector. If the problem persists, see "Contacting Dell" in the

Owner's Manual for instructions on obtaining technical assistance.

POST Beep Codes

If the monitor cannot display errors or problems, during POST the computer might emit a series of beeps, or beep code, that identifies the problem. The POST

beep codes are listed below.



System Messages



Other failure.

See "Contacting Dell" in the Owner's Manual for instructions on obtaining technical assistance.



Computer has started and

turned over control to the

operating system.

No action is necessary.



Beep

Codes

Possible Cause

Corrective Action

A memory refresh failure occurred.

Reseat the memory modules.

Memory parity cannot be reset.

Reseat the memory modules.

A failure occurred in the first 64 KB of memory.

Reseat the memory modules.

The system timer is not operational.