Instrukcja obsługi Definitive Technology ProCinema 6D

Definitive Technology głośnik ProCinema 6D

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Definitive Technology ProCinema 6D (7 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/7
O W N E R ’ S M A N U A L
THANK YOU
for purchasing the Definitive Technology ProCinema 6D System. This high-performance six-speaker
system is designed to deliver equally superb sound for home theater and music. Please read the
instructions carefully to familiarize yourself with the speaker system.
PLEASE INSPECT FOR SHIPPING DAMAGE
Each loudspeaker leaves our plant in perfect condition. Any visible or concealed damage
most likely occurred in handling after it left our plant and should be reported at once to
your Definitive dealer or the shipping company which delivered your loudspeaker.
REGISTER YOUR NEW DEFINITIVE TECHNOLOGY PRODUCTS AT
definitivetechnology.com/register
PROCINEMA 6D SYSTEM Overall Frequency Response: 22 Hz – 30 kHz Recommended Amplification: 10 – 175 watts/channel
PROCENTER 6D CENTER CHANNEL
Dimensions: 10.5” W x 4.25” D x 4” H
Frequency Response: 55 Hz – 30 kHz
Efficiency: 89 dB
Nominal Impedance: Compatible with 4 – 8 ohm outputs
Driver Complement: Two 3.25” BDSS bass/midrange drivers
coupled to two 3.25” pressure-driven
planar low-frequency radiators, 1”
Pure Aluminum Dome Tweeter
Recommended
Amplification: 10 – 175 watts
PROSUB 6D SUBWOOFER
Dimensions: 10.38” W x 13” D x 13” H
Frequency Response: 22 Hz – 150 Hz
Driver Complement: One 8” woofer with polymer cone,
one 8” infrasonic radiator
Built-in Amplifier: 250 watts RMS
High Pass Filter: 6dB/octave speaker level at 100 Hz
Low Pass Filer: 24dB/octave continuously variable
(40 Hz – 150 Hz)
Power Consumption: 60Hz 100-120V, 2.1A
PROMONITOR 6D SATELLITE SPEAKERS
Dimensions: 4” W x 4.25” D x 7” H
Frequency Response: 65 Hz – 30 kHz
Efficiency: 88 dB
Nominal Impedance: Compatible with 4 – 8 ohm outputs
Driver Complement: One 3.25” BDSS bass/midrange driver
coupled to one 3.25” pressure-driven
planar low frequency radiator, 1” Pure
Aluminum Dome Tweeter
Recommended
Amplification: 10 – 150 watts
PROCINEMA 6D SYSTEM OWN
PROCINEMA 6D SYSTEM OWNER’S MANUAL
channel +(red) speaker wire (high-level) out on the back of
the ProSub 6D.
5. Wire the – (black) terminal of the left ProMonitor 6D to the left
channel – (black) speaker wire (high-level) out on the back of
the ProSub 6D.
6. Repeat steps 4 and 5 for the right ProMonitor 6D.
7. Set the low frequency filter control on the back of the
subwoofer to approximately 10 – 12 o’clock. Please note that
the exact frequency will depend on many factors including
specific positions of the speakers in the room, so you might
experiment with a slightly higher or lower setting to achieve
ideal blending between the sub and the satellites for your
particular setup. Listen to a wide variety of music to determine
the correct setting for this in your system.
8. Set the subwoofer level control to approximately 12 o’clock.
Please note that the exact level depends on many factors
including your room size, positions of the speakers, etc. as well
as your personal listening taste, so you might experiment with
the subwoofer level while listening to a wide variety of music
until you achieve the ideal setting for your system.
9. Wire your center channel to the center channel out on your
receiver (or center channel amplifier) and your left and right rear
surround speakers to the rear channel outputs on your receiver
or rear channel amplifier (taking care that all speakers are in
phase, i.e. + (red) to + (red) and – (black) to – (black)).
10. Set the bass management system of your receiver or decoder
for “Large Left and Right Main Speakers,” “Small Center,”
and “Small Rear Surround Speakers” and “No Subwoofer.”
All the bass information including the .1 channel LFE signal
will be directed to the main left and right channels and into
the subwoofer giving you all the benefits of Dolby Digital.
OPTION FOR METHOD 1 HOOK-UP
In addition to the hook-up as described above, you may use an
RCA-to-RCA low level cable to connect the LFE/sub-out on your
receiver to the low-level LFE/sub-in on a ProSub 6D. Set your
Speaker Setup to “Large Left and Right Main Speakers” and a
“Subwoofer” and “Small Center” and “Small Surrounds.”
METHOD 2
1. Wire the left front ProMonitor 6D directly to the left front
channel of your amplifier or receiver and the right front
ProMonitor 6D directly to the right channel of your amplifier or
receiver taking care that the speakers are in phase, i.e. + (red)
to + (red) and – (black) to – (black).
2. Use an RCA-to-RCA low-level cable to connect the LFE
subwoofer out on your receiver to the LFE input on your subwoofer.
3. Wire your center channel to the center channel out on your
receiver (or center channel amplifier) and your left and right rear
surround speakers to the rear channel outputs on your receiver
or rear channel amplifier (taking care that all speakers are in
phase, i.e. + (red) to + (red) and – (black) to – (black)).
4. Set the Speaker Setup of your receiver or decoder for “Small
Left and Right Main Speakers,” “Small Center” and “Small
Rear Surround Speakers” and “Yes Subwoofer.”
5. Set the variable low-pass crossover to 150 and set the
subwoofer level control to 12 o’clock. Please note that you
can set the subwoofer level either by turning the subwoofer
level control on the back of the subwoofer or with LFE level
adjustment in your receiver. We suggest setting the subwoofer
to 12 o’clock and then making fine adjustments to the
subwoofer level using the LFE level control on your receiver.
METHOD 1
1. First, wire the + (red) terminal of the left channel speaker wire
output of your receiver or amplifier to the + (red) terminal of the
left channel speaker wire (high-level) input of your ProSub 6D.
2. Next, wire the – (black) terminal of the left channel speaker wire
output of your receiver or amplifier to the – (black) terminal of
the left channel speaker wire (high-level) input of the ProSub 6D.
3. Repeat Steps 1 and 2 for the right channel.
4. Wire the + (red) terminal of the left ProMonitor 6D to the left
PROCINEMA 6D SIX-PIECE
SURROUND SOUND SYSTEM
This system is designed to be used as a 5.1 Dolby/DTS surround
sound home theater.
WHEN MOUNTING
THE SPEAKERS ON A WALL
• The speakers can be mounted on a wall using the
keyhole hook on its rear panel.
• When you mount the speakers, be sure to install
them properly and securely.
1. Screw in one self-tapping screw (commercially available
5/32 inch / 4mm to 3/16 inch / 5mm diameter) into a
wall that has sufficient strength to support the weight
of the speaker,or into reinforcing material on the wall.
2. Hook the keyhole hook on the back of the speaker
onto the head of the self-tapping screw.
• Check that the head of the self-tapping screw hooks securely
into the keyhole hook hole.
• Do not attempt to install this product onto a wall made of material
that may crumble easily, such as mortar or decorative plywood.
Doing so may result in the screw pulling out and speaker falling,
causing damage to the speaker or injury.
• Do not install the speaker using other methods such as nails or
double-sided tape. The nails may become loose due to vibration or
the double-sided tape may peel off due to prolonged use, causing
the speaker to fall.
• Be sure to fix the cables in place so that they cannot be pulled or
tripped over by accident.
• Be sure to check that the product is safe after installation. Please
note that we cannot accept any liability for accidents, etc. that occur
as a result of where or how this product is installed. If you are
unsure of how to install this product safely, request a professional
contractor do the installation work.
CONNECTING YOUR LOUDSPEAKERS
FIGURE 3 – WIRING AND POLARITY
Strip 0.25” (6mm) wire.
1. Unscrew binding post and insert wire.
2. Tighten until wire is secure.
Identify markings on wire and assign +/-.
Ensure that the speaker is always connected
to the receiver or amplifier+ to + and – to –.
+
-
1
2
Receiver/Amplifier
Satellite Speakers

Specyfikacje produktu

Marka: Definitive Technology
Kategoria: głośnik
Model: ProCinema 6D

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Definitive Technology ProCinema 6D, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Definitive Technology

Definitive Technology

Definitive Technology Dymension DW-45 MAX Instrukcja

8 Października 2024
Definitive Technology

Definitive Technology Dymension DW-65 MAX Instrukcja

8 Października 2024
Definitive Technology

Definitive Technology Dymension DW-65 PRO Instrukcja

8 Października 2024
Definitive Technology

Definitive Technology Dymension DC-80 MAX SUR Instrukcja

8 Października 2024
Definitive Technology

Definitive Technology Mythos LCR-75 Instrukcja

7 Października 2024
Definitive Technology

Definitive Technology Mythos LCR-85 Instrukcja

7 Października 2024
Definitive Technology

Definitive Technology Mythos LCR-65 Instrukcja

5 Października 2024
Definitive Technology

Definitive Technology Mythos ST Instrukcja

3 Października 2024
Definitive Technology

Definitive Technology ProCinema 1000 Instrukcja

22 Września 2024
Definitive Technology

Definitive Technology BPVX Instrukcja

21 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024